Cycra Probend Handguard Install Guide / 2022 Honda CRF 250 RX / MAX'S MOTO SHOP

In this one I install the Cycra full wrap handguards onto my 2022 Honda CRF 250 RX if you have any questions leave them in the comments below thank you for watching

[@ethanausten5968]

These hand guards look so sick on a KTM enduro bike 🔥

[@leewiles3075]

Did the spacer and longer bolt come in the kit? Also, do you think it would fit a 2023 CRF 125 big wheel?

[@bueller48]

I'm in a pickle with my mine. I have some pro taper risers on my pastrana bars that are outboard of the original bar clamps and makes it where there isn't room for the bar clamps of the cycras. I gave up once but maybe I'll try again but maybe I'll have to get different risers.

[@lukefish7562]

About to add some to my 300L. Very helpful. Appreciate it. 🏍💨

[@Maxsmotoshop]

Glad I could help. Thanks for the support.👍

[@BlazinBlades]

For me its all about wind protection and taking the hit when you drop the bike. Short levers are another choice for those riding in warm whether who want more feel

[@Maxsmotoshop]

For me it’s wind protection and I’ll like to fall over on a big hills lol

[@loismartin269]

My bacon needs to use those big things that goes inside the handlebars How do you do that it’s not working it’s just spinning for me in circles

[@sparky_zap69]

Question, how do you get the OEM hand guards off the bike, and what did you do for the lever bolts after? Did you have to use a spacer to take up the space from the plastic mount for the hand guard?

[@Maxsmotoshop]

The stock hand guards are held on with a zip tie and the bolt that holds the lever on as well once you remove the star Ken guards you can put the original bolt back in but it will stick up a Waze or you can order the lever bolts for the 250 R

[@sparky_zap69]

@@Maxsmotoshop yeah, I tried that but it wouldn’t slide over the clutch perch. Guess I’m gonna have to pull the perch off the bar to get the guard off the bars lol

[@brianmurray5696]

Did you just order the 250r lever pivot bolts to get ride off the flag hand guards

[@Maxsmotoshop]

Yes👍

[@stephanelarose2359]

Very useful démonstration for à beginner like me ! do they fit on crf 300 rallye thx !

[@Maxsmotoshop]

👍

[@Gudindio]

Really needed this vid

[@Maxsmotoshop]

glad I could help👍

[@Slampiece88]

Just FYI, these do not fit well on a 2019 Suzuki RMZ250 unless you get handlebar risers.

[@npluvscars2548]

Do you have to get new bars to put the guards on

[@Maxsmotoshop]

No, these are stock bars

[@db1988]

I've ran full wrap hand guards for over 20 years but last year one broke off in a race and I noticed the side with no bark buster felt less feed back and have recently stoped running them for this reason Im torn because I love the protection the give but the drop in feed back threw the bar is undeniable. Especially for someone like me that suffers from carpal tunnel.

[@Maxsmotoshop]

That’s a good point I know myself I like to fall over and hit trees so I’m going to give these a try for a little while 👍 ride safe

[@noahbanewicz8287]

@db1988 This might be a little late but I would try to run flags instead of full wrap around. They give less protection but provide the same bar flex like feel.

[@onewheeler4697]

did you get the 7/8" or the 1 1/8" ? thanks

[@Maxsmotoshop]

I got the 1 1/8 for the fat bars that come on the bike

[@coltondarland7017]

Do you know if the 250rx handguards fit on the 250r?

[@Maxsmotoshop]

Yes they will👍

[@dregsta]

Can you do a fork maintenance for the rx?

[@swingingforgold5743]

There’s not a lot of maintenance to do bleed the air pressure out once in a while and keep them clean and do not blow water up into the seals other than that if they start leaking you’ll need the seals replaced

[@Maxsmotoshop]

👍

[@dregsta]

@@swingingforgold5743 in the Honda manual is says to change the fork oil after the break in period which is 3.5 hrs if im correct. I assume to take out all the metal shavings

[@binoy501]

Can i install g2 throttle tamer with this

[@Maxsmotoshop]

Should be able to

[@jamesbaca6359]

where do I get the spacer?

[@Maxsmotoshop]

They come with The hand guard kit

[@IwishyouwerehereI]

no shot mine didn't come with the bar part:(

[@Maxsmotoshop]

Double check the part you ordered and make sure it came with all the pieces if not return it👍

[@IwishyouwerehereI]

@@Maxsmotoshop i bought them from cycle gear they weren't in a plastic box they were in a plastic bag and the bar wasn't in there i scanned the bar code and i couldn't even find the mode of cycra hand guards

[@bkmz5414]

такие же себе на Honda xr250 поставил

[@seminioni]

You need much bigger screwdriver in the next time bro