D.I.Y. - How To Install And Wire LED Halo Projector Headlights On A Jeep Wrangler

In this video I show you how to install and wire Oracle Lighting 7" High Powered LED Headlights With Halos, on a 2004 Jeep Wrangler TJ Rubicon. If you have been debating on replacing your OEM Jeep Headlights, this video will help make the decision. The before and after footage is literality a night and day difference. The Halo rings alone are brighter than the OEM headlights!
To begin, we bought the Oracle Lighting 5769-001 7" High Powered LED Headlight Pair with White Halo, from Quadratec. To remove the headlight housing, we use a T15 Torxs bit. There are 3 screws holding the headlight outer bezel. After the bezel is removed, there are now 4 T15 screws that hold the headlight housing ring. Once the ring is removed, we remove the headlight connector. We then place in the new LED Halo headlight. Next we lock it down with the housing ring, and then the bezel. From here you can plug the new LED halo headlight right into the OEM connector. We then test the light to make sure it is working. The Halo part of the headlight is not connected to the main wiring plug. There is a red and a black wire coming from the connector. So in order to wire the Halo portion of the headlights, we take a long red wire, and run it through the front grill of the Jeep. We then solder the long red wire to the red wires, coming from both headlights. Next we crimp the black wires, to a ground bolts in the engine compartment. Next we cut the main red wire, and splice in another red wire. This wire will run to the fuse box in the engine bay. We then solder a Mini Add-A-Circuit Holder, to the red wire that we just added to the main red wire. We use the Fuel Injector fuse to power the LED Halos, as this is the fuse we found that only has power, when the engine is running. If you want to be able to switch the Halos on and off, you could wire it to a switch, but for me, this works just fine. The Halos will only be on, when the engine is running. That is it for the install. The next part of this video is the before and after footage. We show the headlights turning on and off, also driving down the road in different lighting conditions.
#ledheadlights #howto #jeepwrangler #jeep #mikegoldengarage #mikegoldengames #haloheadlights #automotive #mopar #jeeptj #rubicon #jeephaloheadlights
All the parts we used are listed at the bottom of this video description.
► SUBSCRIBE! ► kzbin.info...
Support my LIVE streams: Donations will appear ON STREAM
DONATE - streamlabs.com/mikegoldengames
I just updated my Merch Store, now on Teespring! Check it out and let me know what you think of the new design! mikegolden Explosion by subscriber, Boon - teespring.com/stores/mikegold...
Shot in 1080p at 60fps
I hope you enjoy. If you do enjoy this episode please hit the like button and consider subscribing.
My Discord - / discord
My Instagram - / mikegoldengames
My Website, mikegoldengames.com
Also be sure to like my Facebook page to stay up to date on when I am streaming and what is going on with the channel in general. / mikegoldengames
Order the Headlights here -
www.quadratec.com/p/oracle-li...
Precision Screwdriver Set With Tweezers, 32 Pc -
www.harborfreight.com/32-piec...
110PCS Solder Seal Connectors, ELECTRAPICK Solder Heat Shrink -
www.amazon.com/Connectors-Ele...
Mini Add-A-Circuit Holder -
shop.advanceautoparts.com/p/l...
Terminal Set, 520 Pc -
www.harborfreight.com/electri...
1500 Watt 12 Temperature Heat Gun -
www.harborfreight.com/1500-wa...
Metric Combination Ratcheting Wrench Set, 7 Pc -
www.harborfreight.com/7-piece...

[@brodiemcnair9600]

Thank you fro the help mike. I did not know you had another account. Keep up the great work up on both channels

[@SwordInc]

Thank you Brodie! I'm glad you enjoyed this content!

[@skiddysm]

Thanks for telling me about the white being cheaper in my state front lights have to be white only !

[@jacobbrown8561]

Mike Golden Garage thank you feeling the FAST SIMPLE Video... HELPED me A LOT for my 2009 Dodge Nitro. Dodgr Nitro "Grill Removal" Is REQUIRED to Even Remove/Replace LED/Halo Head Lamps. EZ-PZ to "Route Wires" on ALL 2008-2012 Dodge Nitros.

[@ruffo1026]

Perfect video, you help me so much

[@SwordInc]

Thank you so much, I’m glad I could help!

[@ruffo1026]

Brother you should make more videos of your jeep if you still have it, you help people like me who acquired one without experience too much

[@karijennings8369]

So you’re the only video I’ve found helpful, I have a xj and it came with the pos and neg wires as well just not as long do I need to get extensions and hook it up the way you have?

[@SwordInc]

Yeah I would say just some some extra wires and solder them

[@williamlaplaca9899]

What kind of wire can I use as an extension. Does it need to be a specific gauge or will any low voltage stereo wire work

[@closmurda]

How did you correct the high beam angle issue? I’m about to buy a 99 TJ and will be looking to buy these lights. Thanks.

[@SwordInc]

Thank you for asking the question. I just realized I never edited the part two video where I show how to adjust them. Lol. I’ll work on getting that. Idea done this week if it help you

[@stephenhagen234]

I'm buying the Oracle headlamps without the halo. I just want brighter, farther reaching headlamps as I drive home from work at night on the highway and I don't need all the bells and whistles. Just something that I can see better at night.

[@SwordInc]

That’s a great choice! The led headlights are way way better than the halogen

[@skiddysm]

Only 9 more dollars for the halo.... be dumb not to get it

[@Liamhannam]

So does fuse tapping into the fuel injectors not cause the fuel injectors to work weaker? Im sure it wouldn't just my OCD wondering haha

[@SwordInc]

Still haven't had any issues. My understanding is the same amount of electricity would flow through, as there is a separate fuse added.

[@GenVirtu]

How are your lights holding up in 2021. Do you have problems with condensation in the lights?

[@SwordInc]

So far so good! No issues as of yet

[@arieldebin1385]

Great video, easy to follow all the way up to the fuse box. Only problem is in my 2006 TJ I don’t have a fuel injector fuse (in that space I have clutch override). I tried the fuse extender in every fuse slot it would fit and either the halos don’t work, or they’re always on. Do you have any suggestions?

[@arieldebin1385]

Update in case anyone else finds themselves with this issue (is it the right/best answer, who knows, but it works!): ended up attaching an inline 10A fuse, attached a male connector to the end and plugged that into one of my open relay slots that apparently is switched. Tucked everything, including fuse, into an open gap at the end of the fuse box and called it good! Still very much appreciate this video!

[@pavanhegde1825]

@@arieldebin1385 Could you please explain more on this. I have 06 TJ and was planning to do this activity. I have the haadlight withHalo and turn signal lights ready. But not an expert with wiring. Do I have to buy more fuses? What else is needed? Appreciate your details here.

[@arieldebin1385]

@pavan hegde it is difficult to explain details without being able to use pictures, but I will do my best. If you’re looking to have the halos turn on every time you start your ignition (as Mike does in the video) I would start by wiring them exactly as he does in the video, including using the fuse extender and seeing if any of your mini fuses in the engine fuse box are switched (meaning they only provide power to the halos when the key is turned on, versus always providing power). Your fuse box might look and/or be wired differently than mine, so i think it’s a good place to start. If like me you end up not having any switched mini fuses, you can try my approach. I purchased an inline fuse holder (like these www.amazon.com/gp/product/B081DHT8Y7/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1) and a 10A ATC fuse (the bigger ones like this www.amazon.com/gp/product/B000MMH1QW/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1). I followed Mike’s video in connecting the two halos with an extra red wire, then connected one end of the inline fuse to the red wire connecting both halos using heat shrink connectors (just like Mike does with the fuse extender beginning around 10:38 in the video) and attached the other end to a male spade connector (like these, but the larger yellow size from wirefy www.amazon.com/150-Wirefy-Male-Spade-Connectors/dp/B07QF1DXHY/ref=sr_1_3?crid=3V2ZUDEBBY23Z&dchild=1&keywords=wirefy+male+spade+connector&qid=1632960200&sprefix=Male+connector+wirefy%2Caps%2C163&sr=8-3). This male spade connector I then plugged into one of the openings on the far right of my fuse box, where the large black relays are plugged in (this is what my fuse box looks like, I plugged the spade into one of the openings in the bottom right corner, www.bonanza.com/listings/2006-06-Jeep-WRANGLER-3-8L-Engine-BAY-FUSE-RELAY-Box/768969641?goog_pla=1&gpid=341761184097&keyword=&goog_pla=1&pos=&ad_type=pla&gclid=EAIaIQobChMI5MjVzrGl8wIViv_ICh2-swpMEAQYBCABEgJt7_D_BwE). The bottom right option ended up being switched for me so now my halos turn on with the engine, then it’s just a matter of finding a way to tuck all of the wires and the inline fuse out of the way (make sure you give yourself plenty of extra wire to work with). I hope this is helpful!

[@pavanhegde1825]

@@arieldebin1385 Thanks a lot for taking time to explain this. Very helpful.

[@pavanhegde1825]

@@arieldebin1385 I was watching a video where you don’t need to add fuse at all. He just spliced the wire that goes to Blinkers and Parking lights.

[@ricardoportillo273]

Did you remove the "acces.2 10A fuse" for better fitment..???

[@SwordInc]

No, the adaptor fit just right

[@anthonyperez5227]

Did the red wiring you connected them with come with the kit?

[@SwordInc]

Any of the wire that was loose did not come with the headlight kit. Just get some extra wire from a local shop

[@joeshaw2181]

Should the halo Led be wired to the brights or low beams?

[@SwordInc]

If you want the Halo on only when the headlights are on, then sure wire it to the low beam. I have it wired to the ignition, so when the engine is on, the halos are on

[@steveblankenship2413]

my high beams are up in the trees, but my low are right where they need to be, never get people flashing at me, I did the tape on the wall trick and I beleave it was 25 foot back to aim them

[@SwordInc]

What headlights are you using?

[@steveblankenship2413]

@@SwordInc iam not sure of the name brand, I realy dont care about the high beams the low gives me all the light I need, I will be hooking my halo lights up to be daytime running lights

[@SwordInc]

Ok, sounds good

[@falcon2093]

Would be cool if you put oracle lights on FJ crusier

[@SwordInc]

I’m sure they make them for an FJ

[@mynameisciko4885]

My toyota FJ40 also use this daymaker and its looks sick and bright

[@medinaorlando1]

Are the halo supposed to be on the daylight wire or the main nite wires?

[@SwordInc]

Isn't it one and the same? I might not understand what you mean.

[@samgruvr]

I've got the same lights.. and tapped the halos into the parking/blinkers. The halos blink with the blinkers but don't come on with the parking lights.. any thoughts?

[@SwordInc]

I’m not sure tbh. I was confused by how they acted too. We had to try 3-4 different fuses before it worked. Lol

[@directedbydon]

Sam did you ever figure this out? My black and yellow isn’t working for my halos either

[@jodytrujillo7994]

I just watched your video hoping to learn how to wire my halo lights but you skip the part I need to know which is how you connect the red and black wires! ! ! ! 😡😡😡

[@SwordInc]

I showed how if you watch the full video. I don’t see what you mean

[@jjvwguy2489]

Are those not upside down cause high beam on the bottom

[@SwordInc]

No, the high beam shoots upward

[@mattrichter1737]

Have you had any issues after running it from the fuel inject

[@SwordInc]

No issues as of yet. Daily driven since install too

[@terrellronin1370]

Dont know if you guys gives a shit but if you are stoned like me during the covid times then you can watch pretty much all of the new series on InstaFlixxer. Been binge watching with my gf for the last couple of days :)

[@carlkai9832]

@Terrell Ronin definitely, have been using instaflixxer for since november myself :)

[@korbinkylo1921]

@Terrell Ronin yea, I've been using instaflixxer for months myself :)

[@diegocalvin1571]

@Terrell Ronin yea, I've been watching on instaflixxer for since december myself :D

[@amazonledlights]

Hello,I am the manufancture of LED headlights and like your video. Would you be willing to test them? Please reply to me if interest.

[@SwordInc]

I would be interested. Thank you for considering the channel!

[@amazonledlights]

@@SwordInc hi, I have sent the message to your email. Plz check it.

[@Wine-N-Steak]

Is it possible to dim the Halo headlights?

[@SwordInc]

No

[@Wine-N-Steak]

@@SwordInc Do they make dimmer Halo headlights?

[@SwordInc]

@@Wine-N-Steak I'm not sure, but probably not for most

[@Wik432]

hello mike

[@SwordInc]

Hello Wik!

[@Wik432]

@@SwordInc I never knew u had a second channel lol

[@josephlahood4647]

Left amber parking lamp burnt

[@SwordInc]

Yep

[@michaelsmith9078]

Wow - TERRIBLE WIRE ROUTING. You've placed single-wall (hot) wires through small openings with sharp edges. Engine and road vibration will easily cut through the insulliation shorting them out and creating a total mess. NOT GOOD. Better is to use nylon spacing clips.

[@SwordInc]

Thanks for the tips!

[@davidrobinson6353]

Flexible feeding tubes would have been ideal for your cables nice and neat very tidy heat resistant easy to hide out of site cable ties for fixing .👍👍👍🇬🇧🇬🇧🇬🇧