2014 - 2018 Mazda 3 How to Replace Rear Shocks - Not a 5 Minute Job! Lower Shock Bushing Stuck!

amzn.to/49M4gKx - TRQ 2pc Rear Shock Absorber Set Driver & Passenger Sides for 14-18 Mazda 3
amzn.to/3xT0nWU - Rear Upper Shock Mount (The stock ones are aluminum and often turn to powder and crumble away) I was able to reuse them, but there was some corrosion on the stock ones.
The Part number for the Lower Stud is: Mazda Shock Mount Stud 9YA9-01-410
( I couldn't find a link for Amazon, but you should be able to find it with that part number)
amzn.to/44gGAMU - Milwaukee 2567-20 M12 FUEL Brushless Lithium-Ion 3/8 in. Cordless High Speed Ratchet (Tool Only)
amzn.to/44epXBI - Mayhew 61366 Dominator Pry Bar Set, Curved, 5-Piece
amzn.to/49M6s4J - Milwaukee 2880-20 M18 FUEL Brushless Lithium-Ion 4-1/2 in. / 5 in. Cordless Small Angle Grinder with No-Lock Paddle Switch (Tool Only)
amzn.to/4aQ9gPm - IRWIN VISE-GRIP Original Locking Pliers with Wire Cutter, Curved Jaw, 10-Inch (502L3), silver
amzn.to/3w3GFXT - Astro Tools 78314 14-Piece 3/8" Drive Low Profile Nano Impact Sockets - Metric
amzn.to/3xQuCxD - Capri Tools 3/8 in. Drive Semi-Deep Impact Sockets Set, Metric, 8 to 22 mm, 15-Piece
amzn.to/4b5jWto - MILWAUKEE'S Mid-Torque Impact Wrench 3/8" Cordless
amzn.to/4aLRKfh - IRWIN VISE-GRIP Adjustable Wrench Set, SAE Crescent Wrenches, 6-Inch & 10-Inch (2078700)
amzn.to/44bigMF - TONE RMA-13L Super Long Oscillating Ratchet Glasses Wrench, Double Side Width 0.5 inches (13 mm)
amzn.to/3WeYUUP - Permatex 80078 Anti-Seize Lubricant
amzn.to/3Qjjtf1 - Dura-Gold 7-Piece Abrasive Brass-Coated Wire Wheel
amzn.to/3UfDeFl - Permatex 24200 Medium Strength Threadlocker Blue, 6 ml (Pack of 2)
amzn.to/3U7J6R8 - GEARWRENCH 3/8" Drive Micrometer Torque Wrench 10-100 ft/lbs. - 85062M , Black
amzn.to/3Qg5SoP - CRAFTSMAN Torque Wrench, 1/2" Drive (CMMT99434)
Just a quick video showing how the rear shocks on a 2014 - 2018 Mazda 3. The owner bought the replacement parts from TRQ.
This was a very difficult job due to the fact that the bottom of the shock was stuck on the mounting stud. I ended up cutting the shock's outer lower ring and prying it off so I could use vise grips and an 8mm socket on the end of the stud together to remove it. This worked the same for the other side as well which was equally stuck. I was able to clean up and re-install the studs on the vehicle, but it might be a good idea to have a replacement stud handy in case yours is too corroded or damaged. It might also be a good idea to inspect the upper shock mounts for damage or cracks before doing this job because they all seem to corrode and turn to powder and break apart.
I also replaced the front Strut Assemblies and Lower Control Arms on this same vehicle.
Here's the link to the video for how to replace the quick struts:
• 2014 - 2018 Mazda 3 Fr...
Here's the link to the video of the Lower Control Arm Replacement:
• 2014 - 2018 Mazda 3 Lo...
Torque Specs:
59 - 77 ft lbs for the Lower Shock Nut
17 - 20 ft lbs for the Upper Shock Nuts
15 - 20 ft lbs for the Top Shock Nut
Tools Needed:
19mm socket and/or breaker bar or impact wrench with extension
14mm deep socket and ratchet or impact with extension
12mm deep socket
13mm deep socket and ratcheting wrench for the top shock mount
Pry Bars
Grinder or Sawzall or hacksaw (If yours is stuck on)
Jack & Jackstands
Torque Wrench
Thanks for watching!
Please Subscribe!
www.danthefixitman.org
www.amazon.com/shop/danthefixitman
Music used in the video:
'Unproductive Meetings' by Birocratic
As an Amazon Associate I earn from qualifying purchases.