Snowthrower / snowblower won’t start? Step-by-step walk through on how to clean a carb (carburetor).

[@tasteslikepennies2549]

You could not have made that any easier. Extremely instructional video. Thank you very much for this!

[@DavesSmallEngines]

You’re very welcome!

[@facereader99]

Good job. I was looking for a video to see if there is a sail type governor in this engine. Your video clearly showed that it does not. Thank you.

[@rogermcdonald1607]

Dave very good narration of the process as you work on the machine! Video is good and audio. You are learning as we all are. 🇺🇸👍Roger

[@DavesSmallEngines]

Wow, thanks!

[@williampayen4508]

Wish I saw this video before I bought a new carburetor.I have the same exact machine.Gas was coming out the carburetor I changed all the gaskets but still leaked.I might of just needed a good carburetor cleaning.Thank you for this video.

[@fillslawncare]

Hey Dave, if I was in your shoes, I would disassemble the whole carb completely upon cleaning (removing the spring, needle, rubber seat). I have sometimes found that any strong chemical cleaner can soften that rubber Tecumseh seat and cause the carb to not function properly. Just a recommendation. Don has a video on how to re-install the spring back on those tecumseh floats 👍. Really easy Remember that before you buy ANY machine, it's good to see it at least start when spraying the intake or adding gas to the cylinder. Also wouldn't hurt to carry a spark plug checker with you just in case. That can all be done before handing over the money 👍. Usually I see a carb access port on that particular model of snowblower but seems like it doesn't have one. Did you try to carefully remove the carb studs with a torx bit ratchet before removing the cover? Sometimes that works.

[@DavesSmallEngines]

Hey Fill! Great points. All good info. I didn’t want to do a full tear down of the carb given this is an extra step far above most people’s level of capability. I figure if I can fix something with the least amount of possibility of error as possible, more people may be empowered to give it a try themselves. I do have to say, I haven’t seen that video - what a poor student I am! The sensor safe MAF sensor cleaner is also rubber safe, but I agree with you on that point. I did try to get at the torx bolts prior to removing the cover but it was a tight fit. I also wanted to clean up under the shroud to prevent rust in the future. Thanks for watching and commenting - I appreciate it.

[@erwinpierce1136]

Qick easy fix , no parts required . Good Job

[@DavesSmallEngines]

Thanks Erwin!

[@stellarproductions8888]

That sparkplug looked really terrible, at first I thought the engine had no spark. And while the carb didn't really look dirty, as you found out, that leaves you in a false sense of security. Often times its the varnish you don't see, like in the main jet or emulsion tube. Good job cleaning it out, she fired up and ran real smooth after. I think the owner should be pleased. Good video!

[@DavesSmallEngines]

Thanks for watching Stellar! I look forward to your comments. Thanks for watching!

[@stellarproductions8888]

@@DavesSmallEngines Thats very kind of you to say, and I really appreciate that! I always take my time to write comments to nice people that I know will appreciate them, and take the time to reply. Never change buddy, your awesome!

[@DavesSmallEngines]

@@stellarproductions8888 cheers , hope you’ve kicked that flu!

[@patmer2087]

Thanks for the info. I have a toro gas single stage and a toro 60Volt. This spring, I will be tuning up the gas one then sell it and buy another Toro 60volt. I’m getting tired of babying that carburetor! Most say u will spend more on batteries but battery tech is exponentially improving. Mine has gone thru 2 seasons and no problems whatsoever. Either waste time and energy (which is very important for an old arthritis laden man like me) or spend some dough for the “plug n play” ease of use of cordless. Which has now rivaled the power of gas believe it or not! (Talking about Toro 2 battery self propelled single stage)

[@markshuput5228]

I run non ethanol in all my small engines. Always run the fuel completely dry when storing it for summer. Great video!

[@abigrunner209]

Me too buddy. But here we are…😂

[@yparam98]

Excellent video! My MasterCraft snowplow is working again, thanks to you!

[@warrenhoffman653]

Great informative video. I have the same machine only a 3.5 HP. If I ever have a problem I know where to look. Thanks.

[@DavesSmallEngines]

Thanks George!

[@warrenhoffman653]

@@DavesSmallEngines 👍

[@carlmuoio216]

To stroke less internal parts best motor for this

[@nashguy207]

Great job on the repair Dave. It seemed to be running well after you cleaned the carb!

[@DavesSmallEngines]

Yes, thanks

[@Mike-ig2zq]

Great vid Dave. Really appreciate your approach for the average person.

[@DavesSmallEngines]

Thanks Mike - that’s the exact angle I’m after!

[@pchili4]

Nice work Dave! Good clear video👍

[@DavesSmallEngines]

Thanks Stihlman!

[@nrmwntrs]

Nice work Dave, always a good feeling when it starts after a little work!

[@DavesSmallEngines]

You got that right!

[@131nfrank]

Those are some mint wheels 👌 great video

[@DavesSmallEngines]

Thanks 👍

[@thomasstreetman8066]

Thanks for the video. Can you do another video explaining the difference between a one/two stage or single/dual stage snow blower? Thanks.

[@DavesSmallEngines]

Great suggestion! I will see about making one with the guru @donyboy73

[@ryans_small_engine97]

Good video Dave

[@DavesSmallEngines]

Thanks Ryan!

[@QuaabQueb]

Those little 2 stroke MTD snow throwers are awesome machines! I always same them when I can, and you get good money for them because they work well. The major flaw is that stupid baffle on the intake of the carb that directs the intake upward. Why they put it like that I cannot understand. I ALWAY put the baffle on pointing down. Most people leave the machine outside for at least some period of time and water/snow inevitably makes it's way in there and causes problems. You will not kick up any snow that will make it in to the intake of the carb with the baffle pointing down.

[@DavesSmallEngines]

Wow that is a great tip. I will flip the baffle 180 degrees on the blower, and I will do the same on my blower too! I have a 5hp Toro (suzuki motor). Thanks!

[@themowerman]

Good video mate.. stay safe

[@DavesSmallEngines]

Thanks, will do!

[@tasteslikepennies2549]

What are you using to spray into the jet? Is that starting fluid?

[@tasteslikepennies2549]

Never mind mass air flow cleaner car cleaner Etc had to hit rewind

[@DavesSmallEngines]

You bet!

[@grimaceize]

Excellent video and very helpful! Thank you...

[@DavesSmallEngines]

You’re welcome!

[@apatterson8128]

Thanks, Dave. Informative video.

[@DavesSmallEngines]

Glad it was helpful!

[@kevat310]

LOL!! At 1:50 bits of acorn come flying out!! Great vid!!

[@DavesSmallEngines]

Thank you!

[@carlotlouis6331]

WELL DONE

[@stoolie10]

That carb was not that bad other than some small bits of crud inside. I recently cleaned a toro about like that but the carb looked like burnt coffee inside, running great now.

[@DavesSmallEngines]

Right on!

[@billkrause4585]

New Subscriber here, Donyboy73 sent us. I like Bruce's Shop channel too on KZbin.

[@DavesSmallEngines]

Awesome Bill, thanks!

[@Aiden_playz]

i have the exact opposite problem it starts but doesn't shut off

[@goldhunter9641]

Dave tell your buddy if he likes the older equipment such as the old Sears stuff, then he should look into The Gravely Brand Equipment like their, Walk byehind Machines, Riding Mowers/Garden Tractors and Attachments.. It's all gear driven and operated machinery... I'm a fan of John deere but Gravely was probably the best built Lawn and Garden Equipment as far as being powerful and long lasting equipment

[@DavesSmallEngines]

I have never heard of that name. Was it available in Canada? He doesn’t like the older stuff - he just wasn’t financially able to get something newer - now he has this blower!

[@goldhunter9641]

@@DavesSmallEngines Gravely was originated and built in West Virginia and sold all across America, from the early 1900s and I'm thinking somewhere around the 1920s up until the mid 2000s and they were a little Expensive When buying them New but definitely Worth the Money.. There is a lot of Gravely owners in Canada but I'm not sure if they were ever sold New by dealers up there.. Gravely is a very good quality built machine, that lasts a long time.. Nowadays, the Pre-owned Gravely Lawn and Garden Equipment can be fairly affordable in many areas but quite pricey in a lot of areas as well

[@DavesSmallEngines]

@@goldhunter9641 that’s awesome Sam. I will keep an eye out!

[@Ron0963]

Nice Work Dave. No Part$ Required. ^5

[@DavesSmallEngines]

Thanks Ron!

[@stevesmith6058]

Whenever you clean the carburetor with carburetor cleaner or brake clean take the rubber seat out of it or it’s gonna swell up

[@DavesSmallEngines]

I'll do that from now on!

[@dukesworld3020]

good job, extra cash!!!

[@DavesSmallEngines]

You know it!

[@1981DEEPSORROW]

How to mix 50:1 fuel

[@kevinbrooks1104]

2.6 Oz 2cycle oil / 1 gallon premium gas

[@marcelcanuck]

looked like there was water on the spark plug

[@marcelcanuck]

@@hshsgjakanss good call 👍

[@DavesSmallEngines]

Yep!

[@kathykeyser9416]

If I had all the equipment and the nerve to fix it and not mess up, I would. Mine works but has a terrible leak and lost all the fuel. At the repair shop now.

[@ncrdisabled]

are you trying to take Donny boy job?

[@DavesSmallEngines]

No Sir! I only make videos on stuff he hasn’t covered. His videos are far more comprehensive than mine. I just like helping out when I can!!!

[@131nfrank]

First

[@DavesSmallEngines]

second