Why Mastering to -14dB LUFS is Completely WRONG!!

[@mostillusions]

Measureing LUFs for a couple of seconds is not integrated, integrated is measuring the whole song.

[@PaulBondMusic]

Absolutely!

[@whatmusiciwant]

Right, but if the song is already at -10LUFS, it most likely isn't going down any further. So, there isn't really any point sitting through the whole thing. The only time I do that, is if I am mixing my song and want to make 100% sure where it is. For this, he's just making a point.

[@elmoreastro2929]

@@whatmusiciwant you're assuming the song has no dynamic development. If you measure short-term LUFS in a loud bit then the real integrated LUFS may be considerably lower - and vice-versa.

[@ShonnMorris]

@@elmoreastro2929 Exactly. Inegrated LUFS can only be acquired by measuring the whole song.

[@KavasPVP]

Yeah, but if you have for example a track that has build up and breakdowns of 1 minute long and it's pretty quiet (-14lufs) and the chorus goes up to -5 lufs and it's only 20 seconds long, then by measuring the full song you won't get an accurate representation of how loud each section is.

[@taloowa5800]

The other flaw is that you don’t subtract the peak level from your LUFS average. If your meter says -11 and it peaks at -3, your LUFS is -11. Chris Muth, former chief engineer at Sterling Sound. I lived the loudness wars from the vinyl era through CD and streaming.

[@Harpsea]

What peaks were being subtracted to begin. That part confused my. The RMS peaks or DB peaks or what was that?

[@remy333]

Hey Chris. I live up a few blocks north of the current Sterling location in NJ. Gehringer just recently did a tree sr master for me. Good stuff. Did you retire?

[@taloowa5800]

@@remy333 Please give CG my best wishes when you speak to him next. I let my contract at Sterling expire in 2004 but occasionally help them out. I work at home! all the best, cm

[@taloowa5800]

@@remy333 Sterling still occasionally calls me to help out with legacy gear. After leaving Sterling in 2004, I went full-time self-employed.

[@flibflob2785]

The Advice I've heard, and that somehow makes sense to me is "As loud as possible without sacrificing quality"

[@CharlesLouisRosario]

That’s right.

[@ZonedOutWaves]

Okay but how does this work for KZbin who literally lowers your track by like -3.4​-7.5 db... how the hell are these producers beating the normalization YT has set to videos?!. . I've tried ALL of this and NOTHING works. The closest I've gotten is 0.1db BUT ITS STILL INCREDIBLY LOWER THAN THE ACTUAL MASTER.... the actual master is as LOUD AS IT CAN GET WITHOUT CRUSHING QUALITY. This shit is so hard and demotivating fr. Cuz it's just a huge slap in the face when you listen back in KZbin and it completely makes you look worst than a bedroom producer. I'm at my wits end with this crap, spent hours upon hours trying to figure this out and NOBODY can give a CLEAR answer. It's all vague and I get it nobody wants to release the sauce but for FS help the people who actually have talent and potential. @@CharlesLouisRosario

[@altmanidan]

as a pro mixer I can validate what this guy is saying. I've been mastering for years with -10dBFS RMS (very close to -10 LUFS) and I never bothered changing anything when the whole loudness normalisation algorithm appeared. its not just a number, more than this usually sounds a bit over compressed a bit harsh and below this is not compressed enough. we need compression for everything to sit well together, its not just a loudness thing and -10 usually gives me the right amount of compression without adding any distortion. loud and clear

[@jagojames]

The information in this video is completely wrong. This is not how you measure loudness and will give you a false result. The -14LuFS figure is NOT a peak measurement. It is the average value (integrated loudness) across your whole song. In this way some parts can be louder than -14Lufs short term loudness (which is what he is measuring) as long as you have quieter parts to balance it out.

[@Unders]

👌correct. However his method does give a good ballpark, Quickly. Granted its not the "correct" way to do it. An i agree with you here that for the purpose of the video that would have been a better choice. As more people are familiar with measuring integrated that way.

[@malcolmmcgeorge1343]

@@Unders Sorry, I have to disagree with you. It very much does not give a ballpark figure because he is only measuring the loudest bits. This is why he thinks mastering to -14db LUFS is wrong when it isn't. Measuring the loudest bits gives him much too high a figure which is why he thinks other people are not working to -14 when they probably are if he onlly measured them correctly!

[@valdir7426]

yes it's a bit misleading. still most people take the short term LUFS and use the loudest part of the song as a reference for the whole song. that's what a plugin like ozone will do if you use the master assistant, it will only listen to a part of the song. so this is sort of a global misundestanding here.

[@VisionsMusicGroup]

Thank you. I was scratching my head watching this "fake news" as well. But I'm just a B-level bedroom artist, so what do I know compared to this professional.

[@emptyspace123]

But Izotope's article comes to the same conclusion. Are you suggesting that Izotope doesn't know how to measure integrated loudness?

[@djnaydee]

Yup. I've been mastering at -8 for many years, because from all my testing, its the loudest I can get songs without introducing distortion or artifacts and still keep that punch that hits you in the chest.

[@ghfjfghjasdfasdf]

What do you use on your master bus?

[@IanJCole]

you should be using Integrated LUFS across the track not a 2-3sec loud part so your information is flawed

[@Fritz2824]

no, just before his own measurement, he went on the website where we can see again -10 / -6

[@RobHarrison]

BTW this comment is right. You don’t measure LUFS over part of the song, the quiet bits are included in the calculation. That’s how streaming services do it and it’s in the standard.

[@Fritz2824]

@@RobHarrison it's disgusting on youtube, there's -14Lufs normalization, and it still have gap between music uploaders, some tracks are quiet, and other loud..... my track is -14,8Lufs and is quieter when i compared it with some artists, famous or not

[@RobHarrison]

@@Fritz2824 would you like me to take a look at your source audio wavs to see if I can identify cause of issue?

[@RobHarrison]

Obvs KZbin won't turn your volume up so that 0.8 is not going to come back but 0.8 isn't that different and should not be so noticeable to cause you concern.

[@danielbadideashaver4894]

Yeah, I went down the -14 Lufs road once, everything was quieter than what was out there, across the board. It's the usual gatekeeping from the music industry and it's people giving you BS info to keep themselves ahead. If you're making any pop oriented music, -7 Lufs. I don't care who says it too loud, I don't care who says it's clipping, these crabs are trying to keep me in a bucket and I refuse.

[@cheery-hex]

speaking of clipping, any reference track I pull in is +12-15db in the red in rms and -6 or so on the lufs meter. the rms makes sense but this guy is right on lufs

[@zizzleberries]

-0.30 db always and forever baby

[@KyleTB303]

-0.3 dB for the limiter threshold for room for ISP and -10 integrated LUFS at least, loud parts -5 LUFS short term. Loud music sounds more intentional and more impactful.

[@Mitsch76]

In fact you do keep fighting the loudness war. Making bad masters. "I don't care who says it's clipping." ;-)

[@zizzleberries]

@@Mitsch76 if everything's clipping, nothing is.

[@philColour]

This is largely on point. As others have mentioned you do need to play all the source audio to get the Integrated rating. Point stands though, the -14LUFS is to normalise levels across a range of material for a good listening experience - it's not a target to aim for when mastering. Also worth noting different genres call for different LUFS rating. Most pop, rock and dance music suits a level of -8 or above imo (even when 'turned down' to -14), but if you push a nu-jazz or lofi hip-hop song to that level you will likely ruin it. I think the biggest problem here is that Spotify has (or had) a guide saying that files above -14LUFS will be turned down, and that this can cause distortions or audio degradation. In my experience, having mastered 100's of songs at -8 or higher that have gone on to streaming services, none of them have suffered any noticeable loss in quality, and I think what the crux of this video is about... is that if I had mastered these songs to -14 in the first place they would not sound as clear, powerful, punchy etc.. in fact, the client would be saying, bro, why is this so quiet compared to all the other tracks I have in my collection i.e. downloaded from Bandcamp, Beatport etc..

[@marcinfilip7405]

If your mix is louder than targed level of streaming service, they will only be lowered in volume, nothing more. There will be nothing to cause distortion, or degeneraton. That alone will not affect quality of original, so there you are good to go. Transcoding may, but should not. The client, on the other hand is the one who ultimately pay your bills, so you do as they say, but mastering -8 vs -14 LUFS alone only makes one louder if you play them side by side. On the other hand if you lower -8 to -14 and play them side by side ( thats what streaming services do ) you have a lot more potential in your -14LUFS mix, because you have a lot more dB of headroom. It is up to you, if you use this potential or not, but it is there to be used. Client on the other hand knows best, and if client wants louder, louder it has to be.

[@LuLeBe]

​@@marcinfilip7405but if both songs peak at 0, but is -8 LUFS and one is -14, and let's just assume it's the exact same mix, the -8 master is more compressed, so even when turned down in volume to be at -14, it'll sound more like a "wall of sound", while the one mastered at -14 will have more dynamics. And depending on the song, one night be perceived as louder than the other. Could be the dynamic one with punchy drums, but also the crushed one with massive synth scapes.

[@benalupasir]

Lol, its a fact bro...

[@jimrogers7425]

One major contributing factor to the current loudness war was moving from tape based recording to digital. With magnetic tape, there was a “universal” reference level of 0 VU (volume units) equaling a known voltage level… in this case .7 ish volts into a specified impedance. With digital, since there was only a maximum level ceiling of 0 dBFS, reference levels now became whatever someone chose as their in-house standard, which is born out in all of the streaming services movie and programming soundtracks being all over the map. Originally, ‘zero’ reference levels were established because of the physical limitations of the medium used to carry the material (tape and vinyl can only be pushed so far before they compromise fidelity). With digital, fidelity as a goal has been compromised for data compaction and loudness. I miss ‘excellent fidelity’.

[@VictorRiley]

KZbin doesn't gain up when you're under -14 LUFS, it only brings levels down once they pass the threshold of -1 dBTP and -14 LUFS

[@niplob]

I noticed that too. I upload a song and it is way quieter than my mix, then I test download the youtube video again and suddenly it's -7LUFS again

[@timothybondaudio]

So, if you take the LUFS of the loudest section of the song, doesn't this artificially increase your LUFS value? If you measure the whole track then your peak section of -8 LUFS drops down to -10/-11 or lower depending on the track. Surely what is important is dynamic range? If you master to -14 LUFS and your peak is -5dB then that's no different to -10dB with a -1dB peak. Also, just from a musical point of view, the streaming platforms' arbitrary choice of -14dB LUFS and -1dB peak (more or less) gives us 13dB of dynamic range to use with no penalty, so maybe this is an opportunity to re-educate ourselves and the public to having music with some actual dynamics? The -8dB 'standard' was for CD production and maybe we've moved on from that? We used to high-pass everything at 40Hz to stop the needle from popping out of the record. Mastering to -6dB just squashes the life out of everything and makes it sound crappy regardless of how well done.

[@valdir7426]

that's what I'm getting from this; the streaming service will analyze the whole song; and use the integrated LUFS for the whole song to determine the "penalty". Which means the loudest part will be higher. Still it means we can have a bit of dynamic inside tracks and have loudest part at -9db or so and quieter at -18db or so.

[@aholder4471]

They are using the integrated LUFs which is basically taking the average of the LUFS over the whole track from beginning to end. Momentary LUFS is the instant loudness number that will fluctuate quite a bit. But I agree with what you are saying about dynamic range. Everyone is talking about LUFS-I and Loudness, but I think the more important number is Loudness Range, which if you look on the pro examples he had here on this video were all between 5 to 10 LU and up, and that seems like a pretty impressive numbers to me because that is the one number I struggle a little with getting that high. I know my mixes are not squashed, I mean none of them sound like Death Magnetic or anything, But I think there is still room for improvement and that last little 5% is the hardest to get and usually the thing that separates great from good.

[@davidallanmusic]

Your thinking is off. The izotope article showed the dynamic ranges of those songs.

[@popsarocker]

Exactly right Mastering to -14 LUFS / -5dBTP is no different than -10dB / -1dBTP; the crest factor is exactly the same; the LRA is exactly the same. This is literally what subtracting peak from LUFS in the video is unknowingly (or cynically) acknowledging: crest factor doesn't change if you simply turn it up

[@chrisb3389]

@@aholder4471 laughing at your Death Magnetic reference. That album really is a prime example of ridiculously bad squashed mastering. A shame, as it was musically decent.

[@moontan91]

i think -14 LUFS is still too loud for certain types of music. -8 LUFS?? that's crazy, it is songs that have no dynamic range and/or are squashed badly. Loudness can only be felt if there are quiet sections to compare it to. Pink Floyd and Led Zeppelin made amazing music that had way more dynamic range. today's music has totally gone to shit. it's music that is compressed to death so it can be listened to in a noisy environment. people don't really listen to music anymore.

[@heddshot87]

-8 is not THAT loud lol, any good mix will easily get -8.

[@moontan91]

@@heddshot87 -8 means you have no dynamics.

[@vincentvandeperre1670]

@@moontan91 psychodynamics is a thing dummy

[@Strepite]

@@heddshot87 -8 is LOUD. period

[@gregmartin6395]

LUFS can be deceiving. It depends on the musical content and how things are mixed and compressed. Compare some of those songs he mentioned with LUFS ranging from -5.6 to -9.9 and they all sound good and passable. In the end, compare, but use your ears!

[@wickydot]

in the article they never stated if the loseless files they bought were the same files that are uploaded to streaming services

[@valdir7426]

they definitely aren't; look at the difference in peak in the two tests.

[@MatthiasLindemann-hp2zr]

3:05 Most of the time, the commercials on the TV were louder than the movie, and when you fell asleep on the sofa, you jumped up from the sofa because the commercials were so loud. The TV stations used this to their advantage so that you could see the commercials

[@RobHarrison]

-14 predates the LUFS system as the LUFS calculation (over the whole song not the loudest bits) was developed to support it. Bob Katz the (yes v professional) mastering engineer was I believe pivotal to it’s development and -14 was in use via his K system K-14 long before the meter or the streaming services existed. It’s based on an 83DB calibrated room. Read up on the Bob Katz K system. I’m not saying you should master to -14 if aim is to chart a single just know that there is a lot of logic around the -14 number and it is targeting home listening and enjoyment over time.

[@astral_brain]

I have noticed that when I measure the LUFS on an unmastered song (no master bus compression or limiting) and normalize the volume to around -1 true peak it naturally ends up very close to -14 dB LUFS.

[@BrianHuether]

The best way to learn modern mastering is use service like Tidal, route the audio through your DAW, place loudness meter on the track Tidal is streaming to. In Tidal turn off loudness normalization. Now you can see loudness parameters of any track you want to reference. Integrated LUFS isn't as useful as checking individual song parts. So listen to some song and then write out LUFS for intro, verse, chorus, build, etc. No approach other than above will get you to hone in on how modern tracks are being mastered. Also run a spectrum analyzer on the track. That way you gain insight into loudness and tonal balance.

[@michaelnorth3785]

It's good to hear someone actually say it out loud .... thank you !

[@CollinShook]

Your video is much quieter than the last 5 videos I watched here on KZbin, broski!

[@milesowens3273]

askers?

[@ArcRunner]

Thank-you for pointing this out. I was first introduced to the concept of a Crest Factor by Bob Katz book Mastering Audio (1st edition circa '03 - there are newer versions) and he advocated for a K-14 standard. I've found that as I and music I love has aged, the stuff that holds closer to K-14 and K-12 holds more of my interest over time than more compressed works. Yes, that's no way to win the chart in the current market place, but I'd put the thought out there for artists to have a mix of your work available that can be mastered to -14, -12, -10, -8, etc. dB So that when you and your fans are older, you have another way to re-vitalize your work.

[@djnaydee]

Yup, when songs are super squashed they fatigue the listener much quicker. Same as youtube videos that are edited with ultra fast cuts. Within a minute or so I cant even follow whats happening anymore and just switch to something else.

[@wheel4732]

Agreed. All these songs he went through are top of the charts modern pop. You think they care about dynamics lmao? I prefer breathing room in my music, so a -12 is where I'll be headed unless I'm mastering for a specific type of music

[@Mikey__R]

This is a great option! You can press your CDs using your -8dB LUFS master, and upload your -14dB LUFS to the streaming services. Radios play from CD so you'll get the radio mix for free. You can provide B side mixes at -14 so your CD customers can still get a decent quality listening experience. Just call the A side the radio edit, or whatever.

[@XPerienceYouthMusic]

Thanks for this information

[@gearslasher7383]

It depends. If you turn on Sound Check in Apple's Music App, the program material is about -15 to -13 dB LUFS. If you turn that off, you see, what's described in the video.

[@jesseeatsbrains]

Looking at the dB change in music from the 80s to the 90s is crazy. No wonder they had their own sound back then

[@PrincipalAudio]

-14dB LUFS-Int is really silly to aim for. It destroys the aesthetic people want from a "master". When dynamics are reduced using limiting, soft saturation and clipping, it changes the overall sound, giving it more of a "dreamy" feel. For electronic genres, most people prefer this sound. Producing, mixing and mastering the same genres/styles in -14dB LUFS-Int totally changes the way it sounds. Yes, it'll sound "more dynamic", but that's NOT the way people want it to sound. Here's my aim:- Blues: -9dB LUFS-Int Rock: -8dB LUFS-Int Dance: -7dB LUFS-Int Acoustic (lacking bass): -11dB LUFS-Int Acoustic (with low end): -10dB LUFS-Int Country: -10dB LUFS-Int However, this changes depending on the tracks and production. These are just 'rough' aims.

[@Strepite]

IF they want that, they can easily achieve it in the mix while having even more control over clipping, distortion etc...

[@ruprechtsrubberglove]

Streaming services turn your -8 lufs track down to -14, and usually sounds worse than a master aimed for -14. I know from experience having a loud track that sounded great go onto the services to be flattened by the streaming normalisation

[@iamjordanpass]

DSPs only turn down your track IF the listener is using NORMALISATION

[@Trinison7]

I have consistently been uploading my Master's at around - 8 to -10 and my masters do not get turned down the way they say. The key is to have a good meter that also reads your dynamics. If your Dynamics are in the green most of the time than in the red and you send in a master of that around -8 it would sound good. Also what this guy is saying is true because I would rip audio to use as references when I master and they are around the same volume levels. Here's my chart. For instrumentals master between -12 to -10. Songs with vocals -10 to -8. However monitoring your dynamics is still key. When using reference tracks match to lufs and RMS of those tracks to your masters. That will start getting you in the ballpark by matching the dynamic range.

[@snubdawg1386]

what do you mean with "If your Dynamics are in the green most of the time than in the red ...." why should they ever be in red?

[@Trinison7]

@@snubdawg1386 MAAT makes a very good that will help when doing mixes and because it allows you to monitor your dynamic range. I will include a link so you can see how it works and you will understand what I mean UCoLCmff5dDTYVTdg4fJV4Bw

[@astral_brain]

Why do you think your masters don't get turned down? Do your songs on, say Spotify, sound roughly equally loud as everything else? If they do, which I'm sure they do, they have been turned down to -14 LUFS as everything else.

[@Trinison7]

@@astral_brain if your masters have good dynamics then when it gets normalize but the streaming services it will still sound loud. It is important to have a meter that monitors your dynamics. So when you are adding a limiter of clipper or both you can keep an eye on how the dynamics are being affected as you increase volume and depth. MAAT meter is perfect for this

[@Trinison7]

@@astral_brain kzbin.info/www/bejne/p4PZm6trlLijpJosi=dGxZDL6OCDCblIl7 a link about that MAAT meter plug in

[@shpater]

1. Acording with your own measurment, all Apple measured songs peaked to -2.5 or -3 dB. This means that Aplle attenuated these somgs level by apx. 3 db. This means that for apple services, if these songs LUFS was adjusted 3 dB lower the song would have been sound same loudnes with extra 3 dB headroom. So acording with your own the best Lufs level is around -11 to -13 dB. 2. To my understanding, the streaming services measure the laudness level of the whole song, not just a 3 second loudest level. This means that the avarage level of these songs is even lower and -14dB starts to feel more the correct number. 3. To my knowledge Apple do not bring up level of quiter tracks, just limit the maximum. 4. The Lufs measure level according with listening curve. This means that tracks with more bass and less medium can be with higher RMS level, and this explains the non flat curve you have shown of the grammy songs.

[@studioMYTH]

Again, it's not 3 seconds he is fast forwarding through the video of the measurement, it's very obvious the songs don't sound like that and he is fast forwarding through the measurement so he doesn't get struck...

[@AutPen38]

I would trust the Izotope article more than the meters of a guy running Apple music into his DAW via a soundcard and his own faders. If you buy the CDs or digital files of the chart-topping pop songs, they really do have LUFS values in single figures. The streaming services then turn them down to -14 LUFS so that they don't stand out as much alongside random songs on a random playlist. But the top pop songs really are compressed and limited to extreme levels, such that the actual masters (and CDs and WAVs) sound much louder and have much less dynamic range than music of the past. The point is that professional pop music is really loud. Spotify will turn it down, but the main reason our amateur tracks don't sound professional is that we don't compress, clip, and limit it as much as the pros do. A master at -14 LUFS just isn't compressed enough for the pop charts.

[@astral_brain]

What most people totally miss regarding loudness normalization is the reason WHY they do it. It has nothing to do with streaming services being advocates of dynamics or wanting to end the loudness war. There's one simple reason: they want their users to have a good listening experience so that they keep paying their monthly subscription fee. A good experience is not achieved if the levels between songs are all over the place. There is no such thing as a loudness "penalty". They simply match the volume of your track to everything else, and this is beneficial for all parties involved. This means you can master your song to any LUFS you want and it will still sit nicely with every other song.

[@davidallanmusic]

Nailed it. I don't understand why people make this more complicated than it needs to be.

[@joe4570]

I dont think music under -14 lufs will be turned up though. In fact I know it because classical music on streaming platforms is still very quiet (because it t3nds to be mastered under -14 lufs)

[@astral_brain]

@@joe4570 It will be turned up to -14 LUFS, or as much as the headroom allows. Here is an excerpt from Spotify's mastering guide: "If a track loudness level is -20 dB LUFS, and its True Peak maximum is -5 dB FS, we only lift the track up to -16 dB LUFS" Adding to the example above, if the original true peaks had been at -7 dB or lower, the track could have been turned up to -14 LUFS.

[@joe4570]

@astralbrain8265 presumably everyone is mastering to at least -1 db true peak though. So yes you're correct but if we assume everyone is mastering to at least-1 true peak then -20 stays -20

[@astral_brain]

@@joe4570 Correct.

[@jeffbridges6110]

I usually go for -9.0 i-LUFS and it ends up around -7.5 or -8.0 . And I don't do this by squashing everything through a limiter. But I do use a limiter in the end chain to catch any random peaks from jumping out. Good video.

[@thomashambrecht6435]

We have some customers who currently don't want to listen to music at all because everything has been compressed into standard pulp.

[@gzis6685]

Fake information that will lead your songs to worse quality when uploading on platforms with normalization applied. Yes, mastering to CD or club levels is important when you go for live performance. But these days everyone is sharing their products via yt or spotify and those are really normalized to -14. So when you upload on one of these platforms song that was mastered to higher values, it for sure has impact on dynamics, volume and overral quality. Try for yourself and youll see. Learnig by yourself is better than listening to someones opinion, who obviously isnt saying all of the information.

[@DieserEineee]

Why should we subtract the peak from the LU-I ?

[@Endless_Skyway_Adventures]

Because the assumption is that the original song was mastered at 0 and it assumes that the streaming service turned it down by whatever the peak is. In reality it was probably mastered at -1 db to account for inter sample peaks so lufs - peak+1 is probably the right number.

[@pigknickers2975]

The relationship between dB and LU is not linear, close but it is not exactly the same thing.

[@fabrikc_official]

correct me if I'm wrong but you're comparing the STREAMING LUFS Limits to a maybe digital or physical release where there are NO limits. You can't do "one master to fit them all", this you should always consider. And you really pick 2 seconds to get the integrated LUFS? Some kind of confusing.

[@EberFilipeSunlight91]

A guy here in Brazil had the information that the big big label producers always knew this, I just want to understand why!

[@RudeRecording]

For CD mastering it was always shoot -9 dB average level with a max of -1 dB to avoid clipping DAC. Note that it hasn't changed from RMS. It sounds like most of the references you cited were within a dB or so from that standard. From what I've seen is that the streaming services will adjust the level down to -14 dB LUFS but won't adjust up to that level.

[@GoogleAccount-kw1mz]

i usually create different files for each purpose. for example: artist - song title - 24 bit - 14 Lufs artist - song title - 24 bit - 9 Lufs artist - song title - 16 bit - 9 Lufs artist - song title - MP3 - 9 Lufs i've always assumed that uploading the 24 bit, -14 Lufs, -1 Peak would always sound 'full' in streaming services. but i've noticed that the compression that happens, when building up into -9 Lufs is where that "mastering magic" really shines. the thing is, every time i've tried uploading the -9 lufs - it doesn't sound as full as other songs that are mastered then brought down by the streaming services. Maybe it can be that one decibel, and I should try -8 Lufs and uploading that.. but it doesnt sound as alive as when i do upload the -14 Lufs. if that makes sense. it's nice to have the option to give away the louder version in bandcamp - or physical copies and digital .zips. and i've noticed that most songs are uploaded between -8 Lufs or -10 Lufs (using the stats for nerds option in youtube). the louder version just sounds flat compared to -14 Lufs. (In my trials of error lol).

[@RobHarrison]

This is actually what many releases seem to do now and historically too. Back in the day you'd never see the same master being used for album and single releases or for use in cinema or video backing. MP3 you really need 24bit to get the best quality but for CD you have to dither to 16. If I'm listening to the album I don't want ear fatigue at all or I'll turn it off but if I'm listening to a single then I can stand a bit more fatigue cos only a few minutes long.

[@SelfPropelledDestiny]

Set up a re-record from Spotify feed and compare the loudness of your uploaded -14 song against other similar songs. You will probably find it very soft in comparison. The bit of compression that limiting adds makes a mix sound fuller and louder, then there is headroom, EQ, True Peak, etc. Point is I’ve uploaded the exact same track to Spotify thrice, every time getting louder, and it literally does play through Spotify louder as well per documented re-recording. And that’s re-recording with normalization on btw.

[@balsampillow]

Are you saying Apple Music, Spotify, etc. DO NOT bring the LUFS down to -14? And if they do, how does that affect the sonic fidelity with LUFS at -6 or -8? How are these top tier mastering engineers prevailing when they send in -8 or -6 LUFS files? Also, are you doing peaks only in your examples or the entire tune (integrated LUFS) Would not that be erroneous or incomplete to not verify the entire file?

[@AndrewMaze]

You can turn Spotify normalisation off in your Spotify settings (just Google it). Or set it to loud mode and everything will be normalised to -11 Lufs. So he's got the point. iTunes on the other hand does not allow users to turn off the normalisation (as far I know). The only thing is matter for iTunes is -1 dB true peak.

[@ParanormalArson]

That's not even remotely what he's saying. At all. He never said anything about streaming services' normalization practices. He's analyzing hit songs and seeing what levels they're mastering at. It may be "incomplete" to only analyze a sample, but it's extremely unlikely that a song with a LUFS of -7dB at its loudest will be anywhere near -14 integrated. It may be a bit lower, but no lower than -9 or so. The point isn't that streaming services aren't going to normalize a track above -14LUFS, it's that mastering to -14 for the sake of matching the streaming service isn't necessary and possibly detrimental depending on the track.

[@valdir7426]

@@ParanormalArson "but it's extremely unlikely that a song with a LUFS of -7dB at its loudest will be anywhere near -14 integrated. It may be a bit lower, but no lower than -9 or so." that's extremely dependent on the song; but it would be cool to have a proof of that.

[@ParanormalArson]

@@valdir7426 I mean, it's really not, with the exception of MAYBE Classical and Jazz. In pretty much any form of "popular music" (i.e. Rock, Metal, Pop, Hip-Hop, EDM, etc), if you have a greater variation in dynamics than that you likely need to change something in your limiting or compression.

[@valdir7426]

@@ParanormalArson this Billie Eillish song has 10 Db of dynamic over the song; I'd be curious to know what the average is over the whole song. Anyway it's clear that the streaming service does lower the level but from -8 Db LUFS or more for the whole track to 2,5 lower than that makes it -10,5dB LUFS; so how do you account for the remaining 4 DB? that's what I'd like to understand. so integrated LUFS is part of the explanation; but if it's not enough; what is it?

[@RiverSongMusic]

Super interesting. My background is in radio - a few things I wanted to mention - radio stations (in US) typically request production to -6db, or at least they did during the decades in your chart which were the years I was in radio. Then the stations would have a compressor to even things out. Also worth a mention is radio stations (and TV too) intentionally play the commercial material louder - they do it on purpose, as obnoxious as that is. This is not always true, but usually. Now I'm producing to Spotify and learning all about LUFS for the first time in my live, even though I spent 25 years producing for radio! I think we've reached the limit, where sound quality will just suffer if people keep pushing it. I do have a question still - wondering about if Spotify "normalizes" things, in other words, if you're citing the LUFS for some top hits, do they play at that level on Spotify without Spotify "changing" the volumes? I ask because sometimes I hear Spotify changes the volume after you upload your song if it needs volume adjustment, and here you're suggesting when I listen to Spotify I'll hear a big hit and it will be playing on Spotify louder, without any "adjustment." Also I thought of one more question! If I am producing a soft, dynamic song, soft folk or even classical with a lot of quiet parts, should I allow for a quite low LUFS-I reading, -20 or something low like that? Thanks! Thanks for the video!

[@alexvelazquez3679]

good shit bud loud in clear.

[@whatmusiciwant]

Dude. I just got into shoegaze and I am currently working on my first shoegaze/alt-rock album. So, thank you for this because I was mixing to -14 and frankly, it's shoegaze I wanted it LOUDER. I mean, "wall of sound". So, thank you for this. It seems, normalization doesn't matter, what matters it what you think fits your genre/album.

[@nallibeats]

bro I can easily reach -8 LUFS integrated when mastering and it sounds loud when I export it but when I upload a song on KZbin it just becomes low as fuck compared to others on KZbin

[@stratocaster539]

Folks, I use no16 limiter which you can find free online. It allows you to compress, limit and clip your music and add more volume to bring your mixes to the desired lufs.

[@KH1DRO]

i use pro L-2

[@kobuk]

This is what Spotify is recommending today. I suspect major labels are now producing one loud master for CD and one quieter master for all streaming services but ultimately I don't care what they are doing because they released garbage for years during the loudness wars era. "Target the loudness level of your master at -14dB integrated LUFS and keep it below -1dB TP (True Peak) max. This is best for lossy formats (Ogg/Vorbis and AAC) and makes sure no extra distortion’s introduced in the transcoding process. If your master’s louder than -14dB integrated LUFS, make sure it stays below -2dB TP (True Peak) to avoid extra distortion. This is because louder tracks are more susceptible to extra distortion in the transcoding process."

[@tobysandovaloficial]

---- Garbage for years during the loudness wars era / 💯 ❤ !!!

[@MikeBrayton]

Legitimate question: Why are the pros mastering higher than -14? For something other than streaming services, right? What exactly? I get that some music sounds better with less dynamic range, and if that's the case then we should certainly do what sounds better, but it looks like the pros master every single song that way? -10 or above. Why?

[@SAZIZMUSIC]

Thank you sir. But now the big question is what will happen if we upload a song with -8dB LUFS in youtube ? Will youtube brickwall limit it to -14db LUFS and make it sound super crashed ? Or will it decrease the loudness of the whole track preserving the dynamics ? That is what i wanted to know.

[@timothystockman7533]

I've been mastering the music sets for my Internet radio station at with a target of -16 LUFS. I almost never run out of headroom. I do some basic gain riding to keep listeners from reaching for the volume control a lot. I'm guided by the indications of a TC Electronic Clarity M stereo level indicator and soon will be trying a Dorrough 280D.

[@timothystockman7533]

And by the way, who wants to emulate the crap the music industry is putting out? Their stuff would sound a lot better if they didn't squeeze the life out of it. But, these days, for the most part, people don't care about crappy sound quality. If everyone else sounds like crap, what's the incentive to be different?

[@brianholtzmusicsound]

Thanks for your diligence on this. Were the songs you analyzed subject to the streaming -14Lufs standard or were they direct from whatever distribution you can them them from? Would ones mastering level be a moot point if the streamers simply raise or lower volume to suit? Also, do you think the gain reduction (Spotify) has an effect on sound quality of an ex: -6lufs track? Thanks again!

[@gzis6685]

Of course. Just try to post it there. Then listen it in your pc and compare to the uploaded one. Youll see for yourself.

[@valdir7426]

they were obviously taken from Apple streaming service; as they had a peak at -2.5 or so. The service did apply a "penalty" but I'd say the -14 dB standard takes the whole song into account; not the loudest part; so the penalty would be a lot lower than the difference between the loudest part LUFS. or maybe there's something else going on as well I'm not sure.

[@VaughnGeorge]

Great video brother !! VG

[@Harrysound]

Can you get more than -14lufs out of Spotify

[@j.o.n.i.h]

When someone listen to your -14db lufs song without volume equalization it's going to be a lot quieter than pro records. The loudness is in the mix. When you get better at balancing your mix you notice that it's easy to get etc -7db lufa loudness. This has been the biggest struggle for me personally for so long.

[@BassBusMusic]

The full story is that they "bought" each track/album. CD/lossless media has always been mastered to louder levels than streaming. There is nothing new in that. Most people do not buy their music. They stream it. It states quite clearly in the article that streaming is set to -14 LUFS. Simple answer is master to -14 for streaming but if you intend to sell then go for higher.

[@DavidCamposComposer]

All these tracks I tested were from Apple music streaming charts. I didn't test CD.

[@abrotherinchrist]

​@@DavidCamposComposer Don't streaming services normalize tracks? I was under the impression they analyzed the whole song and took an integrated approach to how they would normalize. I think what BassBusMusic is saying is that you would have gotten a different result had you bought the CD like Izotope did.

[@mattbielasiak9599]

There also are settings, at least in Spotify that allow a listener to bypass their normalization. Which could be the case in his tests, I don’t have Apple Music so I can’t test it myself

[@garethde-witt6433]

In the early days of recording and mastering music was mixed so the needle wouldn’t jump out of the groove on a vinyl record, it’s when things went digital is when things got l stupidly louder

[@TayajohMusic]

In short, for streaming/uploading to social media: aim for -14 lufs to -10 lufs. For anything else, you can go up to a -8 lufs or whatever feels right.

[@realfingertrouble]

I master my podcast to -16db but that's cos it's a bit draining to listen at -8 or -10db for a long time. But it's a similar thing, 'pros' say master podcasts at at really quiet -23db LUFS, but that means you can't hear it on the Tube or with ear buds. Even for music podcasting, -16db is a little too quiet, but I found -14db a little too grating, but if I was more of a pop podcaster, I'd definitely bump it up. It's getting that sweet spot to not kill any dynamic range but also cut through the environment. I might go back to -14db LUFs at some point.

[@thewizardtk]

GUYS!! LUFs is essentially a measure of dynamics. Master to whatever LUFs gives you the effect you’re after since Spotify balances them all out anyways

[@scaz2181]

So can i set the limiter to make my song play at -10db long term without spotify lowering the volume of it?

[@volpofficial2k]

it just doesnt make sense, i upload a -8 lufs track to youtube and its not loud, it makes the audio quiet, please someone help

[@volpofficial2k]

@@DerSilvano wdym?

[@lacikollar64]

KZbin lower your sound to -14 haha

[@BostonKid-256]

Actually as a producer, I say each genre has its own perfect LUFS level and that's why you are adviced to use reference tracks when mastering so that you can match the LUFs range of the genre

[@clementj2005]

I'm new to mix and mastering, as a movie composer. I'm surprised by this video and take good note of it ! I'm also surprised by some comments which confuse me. You clearly show the LUFS from an analyses website and complete with a quick mesure in Logic so I don't understand why they argue that some additional maths is needed ! You know what, I will trust nobody and do the same as you did but with a measuring of an entire piece of movie music. Thanks !

[@DavidCamposComposer]

Glad it was helpful!

[@rmv9194]

You are measuring the loudest parts. Some songs I am mastering for my band reach -8 lufs in the loudest parts but have an integrated -11 LUFS level (is not that far from the -14 standard).

[@homelessballoon]

What about Dolby Atmos? Apple will not allow a mix with -8 LUFS.

[@frubo_ssg]

FYI: There are delievery standards e.g. the R128 broadcast standard ‘Loudness normalisation and permitted maximum level of audio signals’ by EBU is defined at -23 LUFS (+/- 0,5 LU) published November 2023.

[@RobertRyda]

nice one here. i agree and my magic number is and has been -9-ish, what i would say is - if you cut the subs off, you would probably measure the master at -14LUFS instead of -8LUFS

[@randallnoises]

GREAT video man! thanks a lot!! cheers from Brazil

[@lavinchi6709]

Very interesting and helpful video!!!Grazie Mille!!

[@LordBiffClips]

so will spotify mess with a -8lufs upload in any way?

[@Garry646]

it will turn down the volume at playback depending on the user settings

[@dogsam8066]

You are right, some people complain that you measure the peak loudness in real time, but the mainstream DAW can measure the overall average loudness of the audio, and the results are still very close, most of them are above -11LUFS, and none of the most popular styles of music I have tested are around -14. The only confusion is whether the audio I downloaded is compressed by the platform?

[@Beizeiten78]

The new Queens of the Stone Age record, ran through my interface and meters, has the meters in the red nearly the entire time. LUFS around -6.0. Still sounds good, but I think that’s a bit ridiculous for a “professional” mastering.

[@vidworxsfx]

@Beizeiten78 I agree, there was a Bruno Mars song, same deal in the red distorted way out of balance with the bottom end and it sounds like crap I could not believe they released this and someone said yup its good to go, As stated well many of the pros do it this way. Believe me many pros do not think it sounds good, they are just doing what the producer and label asked of them. I remember Bob Ludwig a mastering legend, said he would make 2 versions one how he felt it should be done and one that was asked of him so the client could then make the choice from there. I absolutely hate the loudness war mentality, loud is not better, sure if its done right it can sound passable but the true dynamics if the song had them will just no longer be there in the way it was intended. Take some classic music like Steely Dans Aja as an example ... the music is allowed to breath and have its dynamics kept intact, if this was mastered to -8 or some other insane LUFS it would sound like crap at least to those who know what it should sound like and are listening on a real system. So while yes its dependent on the music I do not like this whole every thing must be ridiculously loud if this one jumps off the bridge we must all jump of the bridge. Call me old fashioned but that's what your volume control is for you can make it as loud as you like. As for SAGE Audio that was ref in this video I have to say one thing and I have no affiliation with them at all, but have listened to his work and to my ear his mastering sounds fantastic open and punchy not some over compressed heavily limited mess, way more natural then most of the big release crap in my opin.

[@darrellroseborough7275]

I totally agree with Beizeiten78; loud definitely doesn’t mean better. Has the loudness competition gotten so bad that we just put stuff out there without considering dynamics? What I here is a bunch of over compressed loud bass saturated music. Loud does not particularly make your music stand out. In my opinion and my opinion only a great song and arrangement makes the song. I’m not saying make the song where you need a hearing aid to listen to but at least in the competitive ballpark. I have no problem with -10 or 12 even. Tracks can still be loud enough but maintaining clarity and dynamics.

[@aisonikamusic]

Thankyou!!! Gold advice. Remastering at around 8ish now.

[@budi_nabota_riwuga]

Here what I focus on is, more to a specific genre of music, we should not look at Lufs in general based on level, but based on music genre, I experiment, for rock music and orchestra that focuses more on the details of musical instruments so that we can listen clearly we cannot make it past -12lufs, if ballad music is a smaller instrument we can raise it to -9/-8 lufs, If jazz vocal and acoustic we can raise it to the limit of -6lusfs

[@theiammike123]

My take. The loudness war is over in a sense. Thanks to the LUFs normalization standard, not every single record from every single genre is obligated to be mastered loud anymore like in the 2000s. It's all now fully up to the producer/artist's vision and taste. In other words, we can have a Billie Eilish record and a Silk Sonic record at the same time w/out having to worry that one is better because it's louder than the other. Me, I would master at somewhere in between -14LUFs to -8LUFs integrated. And it's up to me and my client to decide what we're going for.😊 The only issue is, not every streaming is fully implementing the standard. Case in point : KZbin Music 😅

[@MaxRayMusic]

Nice take. What do you think our true peak levels should be for our masters. I was surprised to see some pro songs with +1db true peak when we are told to be -2db true peak from Spotify. I wonder if the mastering engineers are bouncing out separate versions of the masters, one louder for cd quality and one quieter for streaming services like Spotify and tidal.

[@rmv9194]

I guess they just let it clip@@MaxRayMusic

[@abrotherinchrist]

I heard another KZbin channel saying that the top engineers don't really pay much attention to True Peak. IDK if that's true but I'd like to find out.@@rmv9194

[@wumpoleflack]

I did the same exercise a few month ago and decided my target would be -8 db integrated LUFS. Not -14! You just validated what i discovered on my own. Thank you!

[@noisynerdman]

I have been coming close to this conclusion in my own feeble attempt at mastering. This has confirmed this.

[@vinylmastersgr1036]

In Greece older songs on compact disc were -16 to -14LUFS and they have so crystal clear sound, they don't distort. For nowadays -12 to - 10 LUFS it's ok but not -8 or -7LUFS. Taylor Swift and Billie Eilish are around -8 and -6LUFS. Besides, they have increased the bass and subbass and they have cut the highs from many songs nowadays.

[@georgeabraham7256]

So you are listening to the heaviest dubstep at a comfortable level and an add comes up and you nearly lose your hearing.. what is the problem?

[@ProAudioIQ]

Cool vid! Are you sure the streaming services bring level up to -14dBFS? Initially they only brought levels down. Have you found something that says that has changed and they raise it up?

[@franciscoesmanhoto8445]

I´ve just checked that with a song I mastered for youtube and they didn´t raise it up. A shame cause I was couting on that. I took it for granted... It was my fault anyway. Second step then I compared my master to an oficial Post Malone video music and they definitely lowered it down quite a few dBs to lock to -14 LUFS integrated. So that´s it. The information this guy has given is not false, but the streaming services in fact lower down the songs that have beyond ceiling LUFS. It´s all your choice to work a master louder than you really need.

[@_BangDroid_]

@@franciscoesmanhoto8445 KZbin only applies loudness normalization on some devices, desktop/web player usually but not always, mobile usually but not always, smart TV's usually not.

[@jeanmartin-g8x]

yes but wont the streaming services turn it down??

[@RadicalSurgeMusic]

Ya know? This does makes sense. Some of my songs I've mastered ended up having -14 LUFS be too quiet compared to reference tracks or listening to music in car stereos. The -7 and -8 area does a nice trim on the peak transients when maximizing.

[@josephyagappan1896]

Very useful. Thank you.

[@flinxsnicopert]

Thank ❤

[@Overxpossed]

My latest track has -9 LUFS and -1 peak. Noticed that KZbin lowered the track to around -6.9 db (a 45%), and Instagram just did not touched the levels.

[@MickDarkstar1]

Clipping. Less limiter & Master Compressor, clipping and sidechain compression is key ;) Will sound loud without killing transienst and removing dynamics

[@enkourmental]

Wondering how they get to -8 lufs when Spotify requires a master that's louder than -14 lufs to be under -2db true peak... the loudest I seem to be able to reach is -10 to -12db lufs. 😢

[@MaxRayMusic]

Hey there. So if you see in the article in the video all the pros have true peaks louder than -2db, in fact some even go as high as +1db true peak. I wonder if the mastering engineers are bouncing out separate versions of the masters, one louder for cd quality and one quieter for streaming services like Spotify and tidal, I'll research this more. Anyways, as for getting loud masters you are going to want to run your track through a clipper and then a limiter to get the loudness!

[@enkourmental]

@@MaxRayMusic yeah I think they bounce out separate masters. That would make sense because different platforms have different standards.

[@enkourmental]

@@MaxRayMusic what settings should I use on Fruity Soft Clipper for loudness?

[@MaxRayMusic]

@enkourmental hey I'm not sure as I work in ableton. I would recommend you get a proper clipper because sometimes you will need the hard clipping settings and a soft clipper won't cut it. I recommend standard clip, if you sign up for their newsletter it's only 18 bucks for their clipper. Then watch a tutorial on KZbin on how to use it and you should be golden. Then run it into a limiter at the end of your master chain and you'll get loudness you never thought possible!

[@VAIBHAVSINGHMUSIC]

how to monitor directly from streaming service to DAW plugin??

[@SolarPeel]

At University we are being taught to mix to -6dB (dbfs as per master fader meter in daw) , and then master to -12 LUFS 🤷‍♂️

[@CyanideLovesong]

-12 LUFS-I is a good balance between loudness and dynamic range. Mastering engineer Ian Shepherd recommends -10 LUFS-S (short term, loudness over 3 seconds) peak during the loudest part of the song as a starting point. That will usually end up around -12 LUFS-I for the whole song... MOST commercial music is much louder than that, but it actually wrecks the dynamic range to do that, and more and more people are waking up to that. So your university's advice is good for fidelity, but if you do this professionally you'll deal with annoying bands/managers/producers that want you to master louder.

[@SolarPeel]

@@CyanideLovesong I asked one of the lectures about this, and in short he said exactly that, although, he did mention when he sends stuff off to likes of abbey road they come back generally -9LUFS . He said recently he was struggling to get a piano piece above -10 without destroying dynamics , he sent it to a guy at abbey road and it came back -8LUFS and sounded amazing (as would be expected).

[@CyanideLovesong]

@@SolarPeel Yeah, in the end it's subjective. Also what numbers are we talking here? When you say -9, -8 ... Is that LUFS-Integrated? Or LUFS-Short Term at the loudest parts? There's a big difference. Here's an example of a song that wouldn't have the big dynamic bass that it does if it was more smashed: kzbin.info/www/bejne/foG3c5SGj99lba8

[@SolarPeel]

@@CyanideLovesong LUFS integrated. I think he said you can have short term hitting -4/-5lufs , but I might be getting that wrong! Sure that’s what he said tho. And cool I will check that video out - thanks ☺️ edit: wonder if It’s worth taking the song and putting it through a compressor to hear the reduced dynamics.. might as well hah

[@CyanideLovesong]

@@SolarPeel Wow, that is in hardcore loudness war territory and I personally prefer music to be more dynamic. I think Ian Shepherd's advice is best, but he masters more dynamic than most engineers.

[@DWHarper62]

Spotify allows any song to go to any LUFS volume you want but the default listening settings in the Spotify app is to "normalize" the audio to the -14dB level... KZbin does NOT allow any volume level and sets every recording to the -14dB LUFS... So it depends on the service that is streaming... The best is to get a nice healthy volume and let the streaming services do what they do... That being said, to see any dynamics and punch taken from a recording for the sake of loudness is a shame...

[@quelocoel]

The irony of the guy saying the "Blind leading the blind" completely got me hahahaha. Anyways, thanks for making this kind of videos so the people that actually study we can keep being better than random amateur youtube self-thaught "engineers"

[@touch182]

This is the most controversial upload in KZbins history.

[@Randuski]

Ok I’m izotope: what version of the songs were they measuring? Did they buy and download the song? Because that is a different version than what’s on streaming. Even on izotope software, “some of the best mastering software”, there is a CD, or Streaming option. Streaming is -14, CD is like -8 if I remember correctly. What izotope was measuring on that list was the “CD” version, which is what you get when you download the song. Also, when you tested on Apple Music, my question is, if you measure those songs and they’re above -14, that means that the streaming service isn’t normalizing the songs. Which they do. Soooooooo what’s up with these measurements you’re getting? It’s because you’re not measuring the integrated lufs. You’re measuring a snippet of the song. ie, not integrated

[@bakedcreations8985]

As long as you succeed at shortening the distance between your peaks and valleys without sacrificing the feel of dynamic range you might sound louder at -14 than other songs that reads -14 lufs and above I would guess. Its a matter of denseness. In other words it is not the length but the girth that matters

[@BENWORKIN89]

lmao at the last sentence.....

[@rimmersbryggeri]

In 1975 they were mastering for vinyl and loud as possible is less for vinyl than for digital.

[@taviqmasteringonline2754]

If you master to -9.5 LUFS or higher, you are killing the song and basically dynamicly re-eqing (reshaping frequencies) the track to be unrecognizable based on the original dynamics of the track and the original EQ signature. This is the true irony of making things loud. - At -10 (and in some cases -11) LUFS the music is already LOUD enough without destroying the original dynamics of the song. - A song at -8 & a song at -10 LUFS can sound as equaly as loud if they are limited to the same final peak level limit (-0.2 for example). However, the main difference that will be heard is the +2dB shift in the mid range and high-end and the -2dB shift in the lowend. - When you push a limiter that hard (doesn't matter if you are using 1 or 5 in series) you are literally dynamicly tilt eqing the song. The sound is still equally as loud, It's just our brain and ears are more sensitive to mid range frequencies and up. - Try this then level match the two by ear and see for yourself. You probably won't like the lowend. However, this is one of the very reasons why clipping because so popular. - Even with all the above said, the most important thing is not just getting to a desired level. What's more important is......how you get there.

[@Maioro77]

Does KZbin normalise to any particular LUFS? I put a music video up 6 months ago and deliberately mastered the audio "quieter" to leave it with some dynamics, it is definitely quieter than just about anything else on KZbin.

[@saardean4481]

In case new people wonder , No. same Lufs does not mean that any song with the same lufs will sound „as loud“ as another one. It is not that easy unfortunately. So don’t get crazy over it if your track is showing -8Lufs but sound much“quieter „ than the „Famous Hits“. Lufs does not take in account the Eq and overall energy balance of a song. That’s why I said what I said. There is more to sounding loud than Lufs readings

[@Brown_magick]

Thanks brother 🔥🔥🔥

[@DavidCamposComposer]

Any time

[@eafloe]

After much testing I typically shoot for around -8 integrated. Sounds great in the car to me and I use some of my favorite albums as reference. I refuse to let streaming services dictate what sounds good. If they turn it down, it's their platform so that's on them. But when it's time for manufacturing to CD or vinyl, I know my release is going to sound exactly how I want it to.

[@XanarchistBlogspot]

So stupid, digital has an 80 db + noise floor, if you want it louder turn the volume, louder with the greater dynamics of less compression actually has a greater impact as the difference between the quiet and loud sounds are greater.

[@cagrisimsek7995]

Hi, great video, what loudness level do you use on your youtube voiceovers?

[@garudasomanna]

I don't quite understand mastering at a -8 db level: do we have to push up the limiter's output gain? Would not the song sound squashed?

[@bllymusic9614]

Use clippers and saturation

[@garudasomanna]

Okay; @@bllymusic9614

[@reedy8585]

you produce at -6db so that there is headroom for the mastering (final balancing)

[@galefraney]

I didn't hear you mention what streaming service you are referring to ... for audio in music videos uploaded to KZbin, documentation says that if the audio is louder, it will be re-encoded to -14dB LUFS which can cause the audio to sound worse ... you didn't specify whether you are specifically speaking about music to be uploaded to Spotify, or other specific streaming services ...