dbx DriveRack PA2 Custom Speaker and Amplifier Setup

[@mondragonargelful]

I just bought it and tested, Very good bass quality even in my own setting. I think I have to sell my other processors to save space. I can save 5u in my rack. Highly recommended!

[@theaztecwarrior1190]

Now this was specific as hell thank you I been trying to figure it out all day 😄

[@richardreid1865]

Ehheiedueupwpo❤e❤❤❤❤❤❤❤koodjidosksjeooeejjeoepehfiwideir😅😅oeowjeueieoee😊r 😊r😊rleoeoeiri woo o o o

[@matthewnsiahkyeremeh1876]

I really like this product. Drive Rack is good use for good sounds

[@Sample_Ama_Entertainment]

Can you please re-post - minus the background noise?

[@the5rbeats42]

I just got mine today excited to try it tomorrow

[@kevindavis3603]

AWESOME WAY TO HOOK UP YOUR MOBILE DJ AMPRACK SYSTEM!!! ( LOVIN IT)

[@sdmackpictures]

This saves a lot of time. Thanks.

[@einjarjar]

Ha! They mixed up bandwidth and quality factor (Q). Way to go! The Q values should have been Q4.8, Q7.2 and Q3.6.

[@joeljarvela]

your sub rarely can cope with 100kHz like mentioned in video... :)

[@nounix]

dear dbx professional - please tell us when you will release a 64 bit version of this app for Mac! After Mojave - from Catalina onwards - no 32 bit apps are supported. They are "history"/"outdated". Now the next Mac OS is coming out (Big Sur), and we have held out from upgrading from Mojave in order to still be able to use your PA2 app. But we really need to move on with the "times". Please confirm when the 64 bit version will be available so we can download it! Thanks!

[@nounix]

HELLOOOOO????.....

[@josephasci]

You should DRIVE RACK every sound system!...at least for limiting!.....protect your gear!!!!!

[@GazMakaveli]

I have a question please. I’m a mobile DJ looking at purchasing one of these to further tailor/enhance/limit front of house sound. The remote app also appeals to me. My system is 2x EV EKX-12P active tops and 2x EV EKX-18SP active subwoofers. The DSP control on these speakers have the option to system-match the crossover i.e. the high pass for the tops can be set to EKX-18SP (or other EV models) and the low pass for the subs can be set to EKX-12P (or other EV models). Would I be able to route the signal flow/configure the settings in the DriveRack so the above is maintained? I don’t want the DriveRack crossover controls to supersede the speakers’ system-matched settings. N.B. The outputs on EKX subwoofers are hardwired as a thru output (no DSP out) i.e. they’re always sending a full range signal (see this video explanation - EV ELX200, EKX & ETX Crossovers | How they work and why they are not good options for column arrays - KZbin). Any help appreciated.

[@arjunsree583]

Driverack 260 or PA 2 which one is better in perfomece??.. Please kindly reply

[@medovasar2072]

Hello, if we have mixer QU-16 MAIN LR output going to the input DBX DriveRack PA2 and from there output to the amplifier that connect to the 4 Bose MA12 spks. To ring out room with 4 AKG C7 mics, should we do it at the Mixer PEQ or use on DBX DriveRack PA2 what's called AFS (Advanced Feedback Suppression) Fixed option not LIve? Also perform the AutoEQ on DBX DriveRack PA2 rather than using Mixer Channel PEQs. Any suggestions here! Thanks much!

[@Markkrochuk1979]

Can you add delays for the bass and mid bands?

[@musamusmanfubesi826]

I have a question.... Does it have destroy feedback or does it have feedback destoyer effect?

[@djnoji8638]

Have you all done a video with the array setups yet?

[@georgeogrady449]

How that work with other crossover as 2 channel a and b

[@VREditz07]

Dbx pa2 me left & rait chhenal low output Mel ta he to setting problem solve me bro please video upload karo

[@King_Lante]

How do i set up if i dont have RTA MIC

[@King_Lante]

Please I don’t have RTA mic how do i set up

[@davidmcdonald3614]

Awesome video. Was considering purchase, this convinced me.

[@samk294]

How about the gain input where would I set it at 100% for high and low 100%???

[@charlemaignebolongon7562]

Maam, sir im only asking about your product ,especially drive rack PA 2.. how i can avail this item. ?

[@DeeJay_IMB]

I just got the PA 2 Friday. Does your unit freeze? When I run the setup wizards I get please wait in the main screen, and it disconnects from the router. I have to unplug and plug it back in. Do you think I have a bad unit?

[@djpedromixhouston]

can you upload the video minus background music to distracing. thanks i just bought dbx pa2

[@djnoji8638]

What about a line array speaker or something like the Evolve 50

[@adarshgupta8491]

Sir I can use driver rack on custom made speaker

[@TelmoMonteiro]

You can

[@albertsolorio5464]

Hello I can i setup up using RCF 12’s

[@aaronm9353]

Wow, you must have quite the product on your hands if you’re manufacturing subs that can produce 250kHz. I take it you had PA systems for dolphins and other members of the animal kingdom with extended frequency perception beyond that of humans in mind. Pleased to hear dbx are stepping up to the plate as the first audio manufacturer to recognise the experience of live sound for more than just us mere humans. 😏

[@thennekcdcdthennek6417]

an idiot watching a "tutorial" and suddenly becomes a genius becuase of a "k" accidentally added on "hz" you should comeback to your animal kingdom idiot.

[@obijuan8466]

Having just purchased this unit, why haven't you at least updated all the speakers made by your corporate owners? My PRX800 series setup has been out for a few years now, and should have been included at release.

[@John48778]

How to setup for Behringer amplifier? Not in list amplifier

[@vohmii]

Please, can you post a video on how to connect two or more dbx driveracks to a mixer?

[@Ahla-et]

Unfortunately you can only connect one per mixer

[@ahmedmakhareta985]

My speaker sheet say LP TYPE for highs is bypass and i don't found it in type list what can i do now?

[@kubx718]

i have 2 ev zlx 15 inch powered speakers and a mackie 8 channel mixer but im getting terrible feedback from my speakers when i use two shure wireless mics will this help and eliminate my feedback issues?

[@ScotStevens]

Yes it will. While nothing can correct bad mic placement or mic technique, the PA2 has 12 notch filters that use the RTA mic, sold separately, to listen for feedback while you increase your main gain, after a baseline sound check.

[@timothywanjohi5248]

Help me set up Nexo PS15 speaker settings into driverack PA2 kindly,

[@lanphanh]

Does anyone know if the new PA2 firmware will support Preset the QSC K12.2 with the QSC KS112 subwoofer?

[@abhihugar7383]

How many power amplifier can I dazichain from two output of drive rack pa2 &dbx drive rack 260?

[@protasov-by]

I like functional of this device but doest it possible to turn phase of signal in degrees from 0 to 359? or I need other device?

[@sanjayjpr1981]

Please make this video again without any background music.

[@vadlasreenivasulu8888]

Can we use home purpose

[@sappk4908]

i have QSC K12 for tops & QSC K181 for subs, where should i set the LIMITER at in the app? And where should i set the COMPRESSOR at in the app? Any advice and tips would be much appreciated FOLKS!

[@Tingeltangeltek]

🧐🤔😅@4:20 - yea, Nothing suspicious here, default 100khz(!) LP X-Over for the subs sounds good to me 💁‍♂️

[@johnlackner1193]

DBX - please take out or bring down the music in the background so we can focus on the dialogue better.

[@smalllinerecords7398]

😂

[@DJANDRESXL]

I need help please, I have 4 JBL XLR 100 and 2 SUBS double speaker 18", 2 amplifiers Qsc 1450 and one Crown XLi 2500. I want to connect them and make the set up with a DBX Pa2 but I can't find the proper configuration, could you please help me? Where can I find instructions? I want a 2 ways with mono subs configuration. Thanks a lot.

[@OLDM4N-DE]

If i only have Studio Monitors, which is it then for connect ? High, Mid or Low ?

[@DJANDRESXL]

May I use the 6 outs of dbx pa2 in the next way: 1 out mid and high stereo, second out sub Mono and third out stereo full range? Thanks. My equipment is 4 JBL 125, 2 subs JBL double speaker 18" 2 Qsc 1450 and 1 Crown XLi 2500 Amps, if I may, where can I find the instructions. Than you so much.

[@mr81quangnguyen]

Can I use another brand rta mic other than dbx? Thanks bro

[@AVportau]

preferably not... an RTA mic is matched to it's system... i can't see a Behringer RTA mic being exact to a DBX but probably half ok on it's own Behringer unit... it's worth buying the correct mic rather than buy, try, and then cry and fork out for the real thing.

[@nounix]

what are the main differences between the pa2 and the venu360?? What will the venu360 do for ne that the pa2 wont?

[@TelmoMonteiro]

Good question

[@Johnycable]

The Venue has 3 inputs, for example if you wanted to run subs on aux thru the 360's extra input for separate control

[@cristianravelli4204]

hola faltaria alguna explicacion en español en la pagina.

[@DJNexuz1]

Would anyone help me setup my elx115p to the drive rack? Pleas or help understand if they are settings for my speakers? Or would if i had to customize the setup? Thanks

[@djfoxhype758]

Is There A Way To Save Or Lock My Custom Settings After I'm Done Setting Up The DriveRack PA2 ?????????

[@davidpruitt2338]

How will this work with Peavey PV115D powered speakers. This speaker is not in the library. How do I set up gain?

[@earthling808]

Because your speaker is powered you would only use the DriveRack crossover if you are adding subs. There is another video for setting gain. You will have to use the input meter on the back of the speaker instead of the meter on a amplifier. If it were in the list you would only have to provide the input knob setting of your speaker into the DriveRack. Follow the directions in the 'setting gain' video and use your speakers input knob as if it were the amplifier knob. The only problem is that you will hear the pink noise at full volume. You could cover the speaker with a heavy blanket while you are setting its gain as described in the other video.

[@xTatshx]

mouse pointer?

[@vita-da-evaso6507]

Is It possibile to use it to set different Type of Soundsystem, for example fiesf pa is from JBL and second One from Rcf... How Is It possibile to Equalize them together ?

[@AVportau]

i used mixed brands of speakers. this only works if they are all together used as one large PA. it wont work for 2 different sound stages or directions. set the DBX DriveRack crossovers for what's recommended for your speakers. if you don't know then 20kz-120/160hz for subs and 120/160hz - 20khz for mid/highs should work ok in a 2way split to full range tops. 120hz - 20khz if you're using 15" tops and 160hz - 20khz if they are 12". 3 way is a little trickier coz you need to know your high crossover point for both brands. then use the RTA mic to set the eq. don't have the RTA mic? then you have to use your ears... highly recommend the RTA mic which will autoeq any combination of speakers you throw at it to suit any room you work in... just make sure your crossovers are set... and only works on a single FOH direction... if the brands are separated it wont work... ahhh i had an idea!... if speakers are separated you could technically use a 2way speaker system, subs and full range highs, then run a 3way setup in DriveRack with lows doing subs... mid set to full range using the x-over band pass filters doing JBLs... and high set to full range filters doing RCF. you should be able to separately manually eq each set of outputs whilst still having the anti/feedback and compression on all outs... the RTA mic autoeq wont be any good in that kind of split setup though.

[@angelpham5801]

Hated the background music.. barely can hear anything.

[@SrDelbioLima]

It means your system isn't well adjusted. lol.

[@nomore25]

I can hear clearly

[@omarroye6244]

How can I configure this to run a 5 way setup? Horn Tweeter High mid Low mid Subs All on a separate amps

[@AVportau]

sounds like you'll need 2 driveracks for that.

[@catcookcode]

I can plug JBL monitors?

[@jeanwislybrisma2538]

Good work bro

[@thehungariankid]

DSPs can add delay due to the time it takes to process the signal. This can be detrimental when mixing two tracks. What is the delay in ms between the mixers monitor output and the DriveRack

[@martijnvv8031]

It's a tiny delay, but you can hear it...... my workaround for this 'problem' is very simple, I just connect the booth output from my mixer to a separate amp (that signal of course doesn't go thru the DBX) and have two monitor speakers very close to me. You can also use powered speakers as booth monitor if you don't want to haul an extra amp.

[@sonidosensacionlatinamemom254]

muy bien tutorial, graxias ??si mis amplificadores no stan n la lista q ya trae de fábrica q pjedo hacer

[@r0m4nt1k]

+Guillermo Vazquez Hola Guillermo no soy un gran experto en esto pero lo poco que te puedo ayudar es que si no estan tanto tus speakers como tus amplis entonces busca la opcion custom, tambien decirte que aunque esto suceda puedes tomar cualquier preset como referencia ya que en su mayoria las speakers de hoy en dia tienen mucho de similar vale? revisando espesificaciones de ambas, por ejemplo si tienes X marca pero ves que es muy parecida a la jbl o qsc poes asi creas tu preset basado en ese mismo. Espero te haya podido colaborar en algo. . .

[@wirelessdj]

Thank you, that explains a lot.

[@joelbradley5731]

hi would you recommend this to use with a pair of turbosound subs Milan 18" and RCF 12" art712 monitors? will this make a big difference? thanks

[@mrjn5786]

hey but what if i have a 3 way powered speaker already. where should i connect it in 3 way output of driverack??? pls answer me. Thank you! :)

[@earthling808]

If you have a powered speaker that has separates amps for lows, mids and highs then you don't need to use the crossover in the Driverack. If you only have one input on the speaker and you want to use separate subs then you would use the DriveRack in Bi Amp mode (2 way) and use the Mid/High output for your speakers. So you wouldn't use the DriveRack in 3 way mode. Your powered speaker is already separating the lows, mids and highs.

[@Emmanuela598]

can I connect powered speakers (qsc k10) and non powered speakers (peavey sp5 vis. peavey pv 500 amp) onto the one driverack pa2

[@niklasg4777]

+Edward Mann Yes!

[@jeanwislybrisma2538]

Thank you bro ,Good job

[@Shreesamarth.Sound..]

Help me my pa2 bass drops ???

[@MinionRocks]

ROFL !! - 4:07 - "Our subs are able to reproduce frequencies from 40Hz to 250KHz" !!! I guess no dbx engineers had approval over this video. It's OK though, because they set the low pass at 100KHz. Go marketing go !

[@lml1501]

+Minion Rocks ha ha, I looked for a comment like this when I heard it myself.

[@johnred1]

I caught that, too. Salesmen at work.

[@MrJmp810]

I only have 2 qsc powered speakers. Would this be a worthy investment or should i go a another route?

[@paulscire5763]

Don't waste your time or money. You don't need to this much processing power to run a pair of powered speakers. Besides, the powered QSC stuff sounds really good right out of the box. If it ain't broke, don't fix it! Good luck, dude.

[@ScotStevens]

While QSC speakers are awesome (I use them in my rental fleet), they are incapable of placement and room correction which the PA2 excels at (as long as you get the RTA mic, sold separately). This one device makes your speakers sound like they are being operated by a true sound engineer.

[@ludman2299]

Scot Stevens Question to Scot....I have k12.2's....May I ask you how you're setting up your speakers in the driverack?

[@earthling808]

You would only be using the DriveRack in full range mode but the Auto EQ function is extremely helpful and fast to tune your speakers to the room. Instead of just ringing it out by ear.

[@dotatv6506]

I only have 2 speaker . Would you pls tell me how to connect them to the pa2

[@Slicklickz]

+Richard Ta Use the high outputs.

[@electrosound4595]

which one is best drive rack venu 360 or pa 2. pls tell

[@atlargegroupllc2694]

Venue 360 way more options

[@SEELEYJP]

why would you fool around with the para eq , before you auto-eq ???? its all gonna change after you rta the system/room

[@earthling808]

The parametric EQ settings that are shown are for the passive speakers if your particular speaker is not in the library. That sets the speaker itself to its flattest response if it were in an anechoic chamber. This is necessary because you are bypassing the internal crossover of the speaker. Those EQ settings come from the speaker manufacturer. Once the speaker itself is set to flat then you continue with auto eq using a measurement mic in the room to counteract room resonance.

[@ghandikpesona1270]

seting sobwoofer dbx 260.gagal

[@diegodeejay4120]

Podrían hacer algún vídeo en español ??🤷‍♂️

[@KellyMercerhfx]

It's hertz for the lower end, not kilohertz. 100 hertz, not 100 kilohertz

[@danielbrooks3452]

I've watched the setup Video for the DBX PA+2 on KZbin. In the video the person is using two JBL high/mid speakers and Two JBL subs with Crown amps. My first question is how do you use two amplifiers for a High/mid speaker. The two Neutrik speakons on the back of the speaker are to go from the amp into speaker and then out of the speaker to link to another speaker. My second question is in the video the speakers, subs and amps are not in the preset list so the person goes into not listed list. How do you no what frequency the speakers are and how do you no which is the correct butterworth bessel and linkwitz Riley filters to use.

[@earthling808]

First: When you are bi amping or tri amping as in this video the crossover is in the DriveRack so separate cables come out of the back of the unit for each band of frequencies. The output cable for the highs goes to the amp for the highs. The output cable for the mids goes to the amp for the mids. From the mid amp a cable is connected to the Low/Mid input of your speaker and from the high amp the cable is connected to the High input of the speaker. However, it sound like your speaker is not biampable, if it only has one input for both mid and high drivers and a parallel output for another speaker then it has its own crossover inside the speaker. Some speakers allow you to move a switch to separate those drivers and bi amp the speaker. Then one input would be for mids and the other would be for highs.Second. In the video he doesn't go into a 'Not Listed List'. He selects 'Not Listed' from the list. All of the settings that are input after that have to come from the speaker manufacturer of the speaker you are using. This is only necessary for passive speakers that are being biamped because you are bypassing the internal crossover.

[@Markkrochuk1979]

Can you run rca adapters to xlr for the input and then xlr to rca for outputs?

[@martinchinchilla3421]

en español donde veo los tutoriales

[@albertobaro3909]

Wow . very nice

[@ruzzellmelgar8882]

New subscriber here

[@jairmendes8753]

porque nao fas vidio aula em portugues brasil

[@lml1501]

you have some super hybrid subs.

[@martijnvv8031]

@ 3:24 Please update the app and REMOVE that lock on the x-over tab !!!! It's extremely annoying !!!

[@Shreesamarth.Sound..]

Sir plezz India hindi language setup help me

[@almas7123]

Help. What exactly is this for? Is this a crossover? Why not use just a standard crossover Someone explain, thanks !

[@Ahla-et]

It is basically a crossover with a little extra things bulit in

[@Frank5]

Subs are in Hz not kHz !!!

[@josalc84]

Update the freaking app to work with iOS 11

[@marcosduarte1237]

Falta explicação em português. Brasil

[@Unknown93]

kkkkkkkkkkkkkkkkkkkkkkkkk cara, vc precisa aprender inglês, 99% das empresas de áudio no mundo trabalham com sistemas nesta língua, sem contar os treinamentos, tutoriais, etc Para de ser preguiçoso e vá estudar kkkkkkkkk

[@blessingschirwa5745]

Nice video but next time reduce the volume of the background music

[@Shreesamarth.Sound..]

Sir plezz Dbx PA2 setup in language Hindi

[@koyechitthu1709]

Good

[@Levikeyboards45991195759]

muito bom

[@ajiteshdebnath3120]

😮

[@madurajaya8125]

Dbx 480 😬😬😬🤔🤔🤔🙏🙏🙏

[@pravinvaja5479]

wow

[@barrettabney]

Goodness sakes alive. Please remove that horrid music from the video. Had to stop watching this video due to the music level and annoyance.

[@nguessanbrunoaby1682]

Bonjour svp en français

[@oldstnick137]

,can't here the person talking

[@hnongsreylen5651]

បកភាសាខ្មែរ បកប្រែភាសាកម្ពុជា

[@bighum70]

Can’t here!!!!