DEI Avital / Viper Car Alarm and Remote Start Wiring In Detail

In this Video I Go Over Car Alarm and Remote Start Wiring In Great Detail.
Be sure to also watch my 5 part series / playlist on the installation job from start to finish.

[@stanleyonishi3314]

Thank you soooo much. Super helpful video. I like how you break everything down step by step. I have a greater understanding and feel more confident to tear apart my dash.

[@craiggus365]

I was an Avital dealer/installer from 1994-2000, deja vu...LOL I never had a comeback on an Avital, some of the older Excalibur units, not so lucky. Truth be told the guy before me was not so great at wire management and I'm sure he caused most of the issue I had to deal with. Nice to see the new wiring setup, I've been using crimestopper or Prestige on my side jobs and I've been good so far but I only do them as a side job now. Thanks for the informative video(s!)

[@legendtrevor7284]

i realize Im kinda randomly asking but does anyone know a good site to watch newly released tv shows online?

[@gabrielaustin940]

@Legend Trevor Flixportal :P

[@legendtrevor7284]

@Gabriel Austin Thank you, signed up and it seems like a nice service :) I appreciate it !

[@gabrielaustin940]

@Legend Trevor you are welcome xD

[@brandon9271]

I have a 5305 so this video should be VERY helpful. I can't imagine they changed that much.

[@trav885]

Hey did u install ur alarm yourself? I have a 5305 n I been trying to get as much info as I can on installing it but don't seem to be that much out there for that particular alarm

[@Volvo8Fifty4Life]

Great video, very informational. Thank you for sharing this wonderful information!

[@PD82]

Great video! I recently replaced the vehicle battery on a 2014 kia sorento. When i went to plug in the negative cable on the battery, with keys in my pocket the vehicle started on its own. The only way i was able to shut it back off was by cycling the ignition from off to on. I disconnected the plug to the ignition switch connected the negative cable to the battery terminal and it did it again. Completely bypassing the ignition switch. Any suggestions on how to fix or reset? Thanks.

[@davidtimmerman3121]

thanx for an informative video! i was hoping for an explanation of the function of all the wires on the satellite relay box. i will peruse your other videos to see if it's there somewhere. also anyone reading this, any help would be welcome. i'm working on a custom car where the remote start equipment is being used for something else and knowing the function of these wires would be the clue i would need.

[@imyourhuckleberry7148]

Thank you so much! I was able to install my 5303 successfully because of this video! I wish you had explained the heavy gauge relay wiring because the installation instructions confused me with all the auxiliary 12v (I ended up with 4 wires tapped into one constant 12v) and aux starter connections. Also I could not find information on how to determin if you need a relay for the doors or not, or if you need a relay for the lights or not. Could you please explain how to determin in a particular car if it needs relays in either of these or not?

[@robertrockatowski5352]

I have a strange question at least to me. I’ve had this system installed for a while and what it keeps doing is flagging the brown brake plus wire as being missing. I don’t believe that’s a necessary component however, the remote startle usually work for about a week and then it’ll stop and flash code 6 at me. Now it says brake light plus but I’m not sure how to wire that because it’s not giving me a specific detail. If I’m supposed to see positive voltage on this lead, am I supposed to wire to the ground wire or the hot wire and if I do the hot wire, do I need a diode. Seems to me without one I’m gonna pop something in the system .

[@fernando651]

i just did a viper 5204 in a 2004 corolla. it went smooth but i spent hours trying to figure out why it blinks 7 times in MTS mode and 8 times in auto mode.. finally figured out with some help that i mixed up the black/white wire with the white/black wire!! the wires are so thin its hard to tell which color is stripe and which is wire color.

[@SpiTxAciD]

Wow subbed! Thank you, this is gonna help me rewire my car a bit better than i already re did haha

[@Lesscoelectronics]

Im glad to hear it helped.

[@oodles86]

So in order for me to connect a positive alarm wire to a negative car wire, I'd have to use a relay?

[@danieltemper9953]

Thanks brother explained clearly

[@mauricioalonso7378]

if all I want is to upgrade to a newer remote starter same brand. do I need to re wire everything or can I just replace the box

[@viasat1058]

Hello, my remo started get stuck on startup ( starter gets going after it starts) any suggestions ? Thanks

[@russrocket2883]

I just installed a Viper alarm system 5305v and I need some help on a couple of issues, first the alarm goes off as soon as I turn key on. Second, the starter stays engaged during remote start, I think on this one I just got to get system to learn tach but cant get their until I fix first issue. Any help would be appreciated.

[@TuanNguyen-bq4kf]

Hi sir.. we bought a car and has this system but no remote because the vehicle was a repo. How do we order another remote? Thanks!

[@youngsumma]

im having issues with my viper smartstart 5706v that Best Buy installed in my 2010 accord coupe. I just recently swapped out the stock radio for a pioneer radio head unit. prior to installing I had to disconnect the (-) battery terminal. After I got everything installed I started getting low voltage warnings on the viper fob. now the smartstart won't turn the engine on. do you think it could be the low battery? 2. does smartstart have any dealings at the radio? (I wouldn't think so, but im just trying to make sure) please help.

[@robertrockatowski5352]

Having trouble with my alarm system. Every time I add the plus brake white wire that’s required by the alarm it shuts my alarm down. Everything but the windows and door locks. If I disconnect the wire, my remote start works fine. It works for a week and then I have to reset the alarm. It’s specifically for the positive brake light input. Once I attach the positive brake light input, it shuts the auto start down come completely until I disconnect that lead. Is there a specific way other than tapping into the brake light lead?

[@Lesscoelectronics]

You must have the wrong btrake wire, if it has +12v on it, it wont allow rs to operate at all, recheck that wire

[@masterofnone7846]

10 years later!!Interesting!Why do some cars u have to cut door wire in half for factory alarm to work?

[@artistlomo507]

Where does the orange wires goes ? It says ground when armed

[@jordinrubingh8500]

I have a 2007 ford fusion with the viper 4105v, the only thing I cant figure out is how to shut off the factory alarm with viper remote unlock? Thanks for any help. It will unlock the doors but as soon as you open the doors the factory alarm goes off.

[@LifeMuch]

Can you break down removing this alarm? I have a Viper 500. Cam will turn over and run, but only if I pedal the gas. I’m pretty sure it’s interfering with the VATS system on my 93 Cadillac Fleetwood.

[@jorgehernandez1970]

Hello my friend!! Im planning install a viper 3105V on my 09 chevy express, comes with no power locks and no remote either so i still need baypass to perform the job?? Thank you!!!

[@Lesscoelectronics]

yes, that van has a passlock anti theft system in it

[@DanielTurnbow]

yes i have an avitol 3300 , i noticed my yellow wire popped out of clip? it is for igniton is that why my car will start with alarm goin off, because that wire popped out and how do i get it back in :)

[@RobertBrown-ow8di]

Do you have wiring diagram for 2017 kia forte and compustar 7900as alarm what wires goes where

[@anandrattu]

Hi I just changed my starter, I disconnected the negative terminal of battery, after that my viper 5706v remote starter is not working, lock unlock is fine, if I put the ignition on with key and start with remote , it start, can u please help me????

[@angelcosme2127]

Im having trouble with the green wire. Im not sure where to wire it. Do i have to wire it to 5 other wires, so i can wire and diode to each purple (dome/lock car wire) wire in each door and tailgate? I have a screen that shows which door is open. Its a 2017 4 door jeep jk. Thanks.

[@Lesscoelectronics]

This should help: (I'd use the yel/wht myself...) All Door Trigger / Dome Light YELLOW/WHITE (+) UNDERDASH LIGHT OR PASSENGER SIDE KICK PANEL, HARNESS TO THE REAR OF THE VEHICLE Driver's Front Door Pin VIOLET (-) DRIVER KICK PANEL DOOR HARNESS BLACK 14 PIN CONN, PIN 4 Pass Front Door Pin VIOLET/WHITE (-) PASSENGER KICK PANEL DOOR HARNESS BLACK 14 PIN CONN, PIN 4 Driver's Rear Door Pin VIOLET/GREY (-) PASSENGER KICK PANEL, HARNESS TO THE REAR OF THE VEHICLE Pass Rear Door Pin VIOLET/YELLOW (-) PASSENGER KICK PANEL, HARNESS TO THE REAR OF THE VEHICLE Trunk Pin VIOLET/ORANGE (-) PASSENGER KICK PANEL, HARNESS TO THE REAR OF THE VEHICLE

[@tremerus1]

Do you know if a Avital 3305L could be installed as a remote starter?

[@kevinacevedo1928]

I have the keyless lock but I wanna know to which cables I have to connect them to make my doors unlock everything I unlock my car

[@jakubbozyk5582]

I have viper 4105V remote starter , there is yellow wire ( ignition out to alarm) what is that use for ?

[@ej9236]

So if I’m not using a remote start or connecting to ignition I don’t need to use the yellow wire?

[@uptownsfinest1598]

I recently removed a avital from my car because I was selling the car , the orange wire was split into 2 and connected to 2 wires any reason why they did that ?

[@kevinhutton1353]

I got orange acc output to red/black on ignition Harness 200ma acc output to black/orange on ignition Harness which needs a relay then I have Red fused 12v ignition 1 input and Pink ignition 1input/output which one do I connect to ignition Harness then I have 12v constant input do I connect that to 12v ignition Harness or other 12v soure then where do I connect Red/Black fused 12v acc/starter input Green Starter input (key side of the starter kill) Violet Starter output ( key side of the starter kill)

[@preetdhillon764]

Thanks

[@hughjasse3375]

Thanks for your videos. I managed to go from nowhere to alarming up a basic daihatsu hijet alarm with a really basic ebay alarm that looks a bit like this. Landbo LB-100D. All works fine except I never used a green/orange 2 wire harness that close/open electrical safety, and have fob functions. What are these wires? Thanks.

[@Lesscoelectronics]

is there an install guide for it?

[@hughjasse3375]

@@Lesscoelectronicshi, there is, but it's so basic that I ended up following you Viper type installs to get it working. I actually found a Russian guy showing an install test with the same one, under the name tsk-100, but identical alarm. And he had a door actuator attached to it. All in Russian, but I know what the harness is now. I'm not using an actuator, manual locks, but I saw you have a video for that too, so maybe next project for me. Cheers.

[@mrchevy20011]

Hey love your videos !!! Hoping you won't mind answering a ?. I am hooking up a viper 5704v to a 2006 rav4 and the viper says to cut starter wire on vehicle and connect H3/4 violet wire to car side . And H3/5 green to key side Now my ? Is do I need to cut starter wire or can I just use the output wire spliced into starter wire??? Thanks in advance ...

[@Lesscoelectronics]

do as you mentioned, just be sure the remote starter's starter output wire winds up on the starter side so when the alarm is armed and you remote start the power will be applied to the starter side, NOT the key side

[@phillipfletcher7442]

Where you get the vehicle wiring daigram for what car or truck.

[@Lesscoelectronics]

email us for one at [e-mail]

[@cheetoztk]

Hey less I have a viper 5204 security and remote start which wires go to which for the remote start? Thanks

[@Lesscoelectronics]

I have a video for finding all your wires, the video is called free wiring info. watch that. that's where all your answers can be found.

[@cheetoztk]

Do u have a video or know how to program the viper so that It can remote start a manual. I tried remote starting my car and it gave me a mts error. One more thing do I need to hook up any of the smaller wires to the bigger remote start wires? Thank you

[@elitecleaning217]

Having a hard time installing a avital 5303 in a 2000 yukon denali How can I get in touch with you?

[@Lesscoelectronics]

call 904 342 5491

[@evo7883]

Ive been trying to get my viper 5706v working and installed it with a db3, alarm works door locks work, but no remote start, flashes 8 times. I believe I need to install that toggle switch for the nss but I do not know where it goes or what it wires into. Could you explain how to wire it up. Thanks

[@Stormnorman15]

I just picked up a Viper 5706v. I’m trying to understand if I need a DB3 for my 2001 Honda CRV?

[@IksinskiTomek]

how much Amps in average this remote starter will drain from battery?? Without remote starter power consumption in my car Honda Civic is about 0.04Amps. After remote starter installation battery drainage will be about 0.10 Amps, more, less ? Any specification in that matter??

[@jowens7896]

I have the same brand remote start only system im gonna install on a 2005 dodge Dakota the key is not chipped and it has no alarm system and no keyless entry any tips would be appreciated but my main question is where should I ground the neutral safety switch wire

[@Lesscoelectronics]

I always ground the neutral safety along with the black/ground wire.

[@jowens7896]

Ok thank you and your videos are a lot of help i bet i watch 15 videos today learning tips and techniques and im gonna use your wire in the drill trick to keep my wires neat

[@horacioaraujo4620]

Hey i just installed a avital 5301L . the remote start turns on but it keep giving power to the starter even after the engine is on. Did i miss something?

[@Lesscoelectronics]

try learning the tach signal maybe?

[@harveybarnes19]

hey buddy my brother wired his remote starter though his fuse box 08 chevy silverado a year ago still no probelms-he cazy or what?

[@Lesscoelectronics]

that is pretty weird

[@biker0110]

I have a question. I was wondering if it was possibly to program a Avital 5303 remote to a viper main harness. I don't know what model the viper harness is yet I have to pull my dash off because of where the guy installed it at its in a stupid place. It's almost all the way up behind my gauges. Before I pull the dash completely apart I wanted to figure out if it's even possibly to program my avital 5303 remote to the viper wiring harness. Will you please let me know much appreciated thanks.

[@Lesscoelectronics]

tell me the other units model number so I can answer accurately

[@biker0110]

Lessco Electronics OK I'll let you know here shortly after I get the dash apart to get to the harness.

[@biker0110]

Lessco Electronics I have a viper 500 esp main harness I'm wondering if my avital 5303 remote will program to it?

[@biker0110]

Lessco Electronics I'm honestly thinking about just ripping the hole alarm out and just installing a new one. Because the way this one is set up in my truck it's all cluster fucked under the dash. Wires are running everywhere and it's a pig sty underneath my dash. What is one would you prefer for a 96 F 350 diesel?

[@ALLCAPS]

What if I just wanted the tilt sensor? Do I need to install of of this extra stuff??

[@Lesscoelectronics]

No, not at all, thats totally fine

[@ALLCAPS]

@@Lesscoelectronics it has been very long, would you recommend any other security system other than Viper that can deliver a great tilt sensor? (:

[@harlymcruz8128]

Hi I have which your DEI avita/viper car alarm and remote start wiring in detail and the 5 part series. I'm going to be installing the the viper 5204v on a toyota solara 2001 I'm having some trouble figuring we're to connect these wire Main harness 6pin connector H1/1 red : (+) 12vdc constant input = white or white/red (+) H1/2 black : (-) chassis ground = ground H1/3 brown : (+) siren out put = siren H1/4 white/brown : parking light isolation wire - pin 87a of on board relay = not use H1/5 white : parking light out put = light switch H1/6 orange : (-) 500ma ground when armed output = not in use Remote start 10pin heavy gauge connector H3/1 pink : (+) ignition 1 input /output = black/yellow(+) H3/2 red/white : (+) fuse (30a) ignition 2/flex relay input 87= Connect to white or to a +12v constant power H3/3 orange : (+) accessory out output = blue/red (+) H3/4 violet : (+) starter output (car side of the starter kill ) = red(+) H3/5 green : (+) starter input ( key side of the starter kill ) = red(+) H3/6 red : (+) fused (30a) ignition 1 input = h3/2 H3/7 pink/white : (+) ignition 2/ flex relay out = red/white (+) H3/8 pink/black : (+) flex relay input 87a key side (if require ) of flex relay = not in use H3/9 red/black : (+) fuse (30a) accessory /starter input = h3/2 Thanks

[@jordanhernandez1762]

Hello I have a avital 5303 and I was wondering I have a 2 pin wire that says horn and connects on h4 of the alarm. would that be the siren connection?

[@Lesscoelectronics]

+Jordan Hernandez the brown wire should be the siren output wire

[@jordanhernandez1762]

Ok thanks

[@SWFLJetSkiRiders]

Where's that trick for manual trans you mentioned ? Thanks man

[@Lesscoelectronics]

search manual transmission in my channel, you'll see it there.

[@o.hdz15]

I have a 2011 Sierra with no fob , do I need a key bypass for this to work ?

[@Lesscoelectronics]

Yes, You definitely will need a bypass

[@trav885]

How do I or where do I go to get information and instructions on how to install an Avital remote start alarm model 5305L in a 02 Chevy Silverado 1500 2WD? Can u post a video on that please? Thanks in advance

[@Lesscoelectronics]

easy, just email me [e-mail]

[@trav885]

@@Lesscoelectronics hey I emailed u. Been waiting on u to email me back. Haven't heard anything from u

[@littletoy01]

I have a viper remote that got installed by dealer. I was wondering if you can help me I have the 5902 when the truck is cold it starts just fine but when it warms up it wont start as if its not getting enough fuel ,2000 Dakota . with key starts every time. Hope you can help me . Thanks.

[@Lesscoelectronics]

+littletoy01 try relearning the tach signal

[@littletoy01]

Thanks for your help but can you tell me how to do that I am two hours away from closest place. Thanks.

[@Lesscoelectronics]

get the install manual online and follow the instructions to reprogram the setting(s)

[@jesusvelez7929]

How to install a Avital 3100 on 2021 F150

[@isaiconchas2602]

I have a viper 4105 remote security alarm that I installed myself on a 95 eagle talon 5 speed manual. when I remote start the car the starter stays spinning. if I start the car with the key and remote start takeover, it works just fine. however if I try to remote start the car, the starter will keep spinning and the only way I can turn it off is with the remote start button. there is a feature called antigrind which requires the use of a relay but am not sure if this is the issue. any help would be appreciated oh also, I have a set of door lock actuators on the car and was wondering how I would wire them to the alarm.

[@Lesscoelectronics]

+Isai Conchas for the grinding, you can fix that by relearning the tach wire. as for anti grind you wire that just like a starter kill

[@isaiconchas2602]

Thank you lessco! I learned the hard way that the alarm will not relearn a tach signal unless the original is deleted first. Did that and it started just fine. On another note, I have a set of door lock actuators that I got off ebay, they may be made by omega so I'm sure you are very familiar with the wires/polarity. Can I wire the green and blue wires from the actuators straight into the alarm door lock harness, or will I have to run the green and blue wires from the actuators into the cars factory door lock/unlock wires? Thank you so much for your videos, they have helped me countless times. Your knowledge is amazing, thanks again!

[@Lesscoelectronics]

sure, you can use the blue and green only, the other wires arent needed unless you are after central locking. best regards

[@isaiconchas2602]

+Lessco Electronics I am going crazy trying to figure out this central door lock actuator situation. I wired the blue and green wires up to the viper door lock harness and I'm getting nothing. do I need a relay, or is there an issue with the remote. I can hear the viper alarm click when I press the unlock/lock button but nothing gives. also, learning the viper remote is different from the others. the viper 4105 uses an auto learn feature to configure the remotes, instead of your typical cycling through channels approach please help lessco, I need to get this put back together but I'm stuck with trying to figure out these locks.

[@isaiconchas2602]

+Lessco Electronics I used two five prong relays and am using the wiring diagram from 12 volt. however, everytime I press the lock button it keeps blowing the fuse. can u please tell me if I am wiring the 2 relays correctly?

[@ggoakeem]

Got any vid got the 4103?

[@tolerbearALTII]

Hey. Can you make a video on how to get your dei remote start off of 24 hour cycling and stuff like how I keep accidently programming my car to start at a certain time? Thank you soooo much! God bless you sir.

[@Lesscoelectronics]

Allen Toler that feature can b turned on/off through the 2 wau remote. download the manual for your system for free at directed.com all you need is there in the owners guide

[@ej9236]

I have the viper 3105 I'm hearing conflicting info on the green and violet wires. I have a 2006 mustang and from what I'm seeing on tech sheet there negative dome supervision . So I only use the green or violet not both correct ? Appreciate any help . Eric

[@Hydemaintenanceman]

I'm replacing an actual 5303 with exact model. Can't find anything or anyone who can tell me what plugs go where. I know it's an old video but maybe if you have the time can you at least send me a pic or post a pic/diogram?

[@johnkosheluk1041]

Hi my name is John I usto be a dei cirt i installer I am going to put the top of live viper 2 way coler remote in my 2018 Hyundai elantra my question to you is do thay make pip harnesses for my car

[@Lesscoelectronics]

fortin does

[@kevinhutton1353]

very helpful but didn't show the heavy gauge wires I sent u an email earlier this video cleared most of it up but not all if u could email me

[@Lesscoelectronics]

+Kevin Hutton which one is giving you a concern?

[@reeisessit]

Do i need to connect the parking light output for a EU vehicle? Here in EU the parking light is not to the turn signal's.

[@Lesscoelectronics]

it is always optional

[@kevinhutton1353]

sorry I was driving earlier and couldn't explain better

[@jowens7896]

I got the unit hooked up but it acts as though i dont have any power to the remote start it doesnt do anything when i hit the button my dakota has 3 12v power wires do i need to use all three i took both red power wires from the unit and wired them together to the red 12v wire on my truck any ideas. Could i have your email address so i could ask that way

[@Lesscoelectronics]

my email is [e-mail]

[@bossboxchevyog6900]

Hooked up remote start sometimes starts fine other times the starter stays engaged what could be wrong

[@Lesscoelectronics]

whats the model starter kit youre using?

[@bossboxchevyog6900]

Lessco Electronics 4105v

[@bossboxchevyog6900]

Lessco Electronics 4105 viper

[@uptownsfinest1598]

I have a question hopefully someone knows the answer . I have avital remote start in my car already it stopped working ive tried everything to reprogram it and what sucks it when it did work I didn't hear a horn or nothing when opening or locking doors so its hard to tell if I am reprogramming it . if I was to buy a different brand would the wires be the same colors ? That way I can disconnect one wire at a time and connect the new one ? Does anyone know ? Im hoping its like switching a radio and just matching the colors im not cheap just broke lol to spend taking it to a professional

[@maxcala78]

Can you please make a video how to connect vsk100 bluetooth to a 5706v?

[@Lesscoelectronics]

:I we'll see

[@kevinhutton1353]

starter ignition acc 2 what size relay do I need

[@Lesscoelectronics]

+Kevin Hutton those are relayed outputs as is on most models with the 12 ga output wires. only on the older ones with the thinner ribbon types require additional relays wired in to power the circuits. I hope I said that well :/

[@itolond]

wheres your trick video for diesel and manual stick ?

[@Lesscoelectronics]

kzbin.info/www/bejne/mmSvaWaPbsd3qNU

[@iantolond1548]

Lessco Electronics great looked at the video. My scenario is a handbrake on is ground. Off no circuit. I assume this will need the solenoid?

[@MkhanEmkay]

Hi, could you please help me locating wires for Honda odyssey 2006 Remote start installation, i am struck half way in the install process... I have Compustar CM800 + Honda SL3 Bypass. I have connected / located most of the wires, but i am not able to locate the below: (1)Parking Lights (+) - Wiring says Driver Fuse/Relay Box 17 pin plug - Red/Black I could not find the wire with that color, i saw a bunch of connectors but could not locate the 17 pin connector (2) Power Lock - Pink /Black ; (3) Power Unlock - Green - The wiring sheet says Pass kick or MICU (which one is MICU 30pin plug please ?) Can you help me with the above wires please and could you point me to the connectors - here are the images to the connectors - Image 1 - oi40.tinypic.com/16iiq1.jpg -Image 2 - i44.tinypic.com/2vkdpxx.jpg Thank you .

[@HEAVYMETAL0209]

Great video! Helps a lot. Old hornet alarm stopped working. Time to replace it with Anvital 5303..

[@donaldjohn223]

You never mention anything about the antenna

[@Lesscoelectronics]

I didn't think it was worth mentioning, What is your question?

[@PedalTheGlobe]

If you cannot understand the antenna that needs no hardwiring you are likely in over your head.

[@estebanmartinezlozano6133]

Exaton

[@m3lloy3llomama]

help me please!!!!

[@TheJfunk91]

HELP! Hooked up everything. It works BUT the starter keeps on going after engine starts from button. Do i need to use the valet to program it? (Brave First time installer)

[@horacioaraujo4620]

TheJfunk91 did you fix this im having the same problem ?

[@suhaibchobi]

can i do a 10 seconds timer output from this unit ? am planning to do a roll-up windows when locking the car .

[@Lesscoelectronics]

No, to get that buy a 528t or a comparable pulse timer

[@suhaibchobi]

Thanks ! can u do a review on the Avital 5305l ? i cant understand the user manual of it.

[@ZynovFTW]

Is the Avital 5305L and the Viper 5706v wiring the same? I have an Avital system that was professionally installed. If I replace the brain of the avital system with the viper brain system, along with the antenna, will everything be plug and play?

[@downjesse]

I have the same question

[@johnlara3568]

I need replacement remote for avital2100. Will any viper remote work to replace damaged remote?

[@1965dbc]

Martin your great just by spending time on break down on installation . Do my homework first on AR3 also found detail wire location for my install. discover ar3 has set default fortin or idatalink bypass. kinda disaapoint with either bypass it's will only do bypass unless firware change options. will call you soon. I'm on the road as truck driver time is everything. david cruz kinda wish bought different system or ask you the best fit with option but to late I'm not going to send back

[@jorgehernandez1970]

Never mind!! I just find it out on google!!