Delta Single Handle Faucet Cartridge Replacement

[@mariepierre-paul379]

I just replaced my faucet cartridge. Thank you so much. I followed your instructions to the letter and it only took 15 minutes. Thanks again for a great video.

[@DirtFarmerJay]

Glad to be of help!

[@womanofsubstance8735]

You mentioned turning the water off downstairs, but there are also valves under the sink which most people would use. It might be good to mention/show that, too.

[@jamesowhitman]

I spent days trying to figure out how to fix my issue. This video showed me exactly what I needed. Thanks for the help!

[@DirtFarmerJay]

You're welcome! Best, DFJ

[@kenclubb8677]

Jay, I have a Delta 978-DST that was dripping, just like yours. I watched your video several times, felt that you presented an informed and detailed process and decided to replace the cartridge myself. I planned to remove the cartridge and take it to Lowes to get the exact match. I live in Central Illinois and our water is hard and limey. After removing the set screw and lubing the hole with penetrating oil, I managed to get the handle off. I got to the 7:24 point in your video and noticed that you could remove the bonnet with the wrench by holding the base with your hand. My bonnet did not move. My wrench was rounding the points and the base was moving in the hole. I both soaked it with Lime-Away and lubed it. I resorted to using pipe wrenches to hold the base and turn the bonnet. The plastic base was slipping and stripping and finally cracked under the torque. The plastic base is hollow and held to the underbase with 2 screws - that stripped out. Now I was going to have to replace the base/hose assembly; or so I thought. The product schematic on Delta's website does not list a part number for the base/hose assembly. It cannot be purchased separately. Nor can just the handle assembly. Long story short: I have purchased a new Delta kitchen faucet - to be installed. I think that there is a design flaw in the plastic base assembly that does allow for a metal piece and place to hold it with a tool. BTW, I was completely unsuccessful in unscrewing what was left of the base from the bonnet. I finally cut the bonnet off with a hacksaw and found lime buildup. I don't think even a professional could had unscrewed that bonnet. I have pics if you're interested.

[@DirtFarmerJay]

Wow, it sounds like you've had quite the experience! If you'd like to send pictures and "talk" more about this, send it to: [e-mail].

[@perrymerkel6638]

I have a low self-confidence level when it comes to these things, but I followed the instructions, sometimes putting it on "pause"…but bottom line is double thumbs up, works like a charm. One thing I would like to add, I called Delta directly and they sent me a new replacement cartridge free of charge, no hassle.

[@DirtFarmerJay]

Great to hear of your success Perry Merkel. It's our goal to help people become self reliant when it comes to home repairs and issues. Keep watching and commenting! Best, DFJ

[@sonnysoldies5288]

Thank you...Delta will send you the cartridge for free which is a big money saver.

[@DirtFarmerJay]

Sonny's, thanks for the info! Best, DFJ

[@gregoryburkhead7813]

Why would they send one for free

[@Melanie16040]

​@@gregoryburkhead7813 Because, if you purchased them new, they have a lifetime warranty.

[@ydozaicirt]

Thank you for such clear instructions! I think I'll be able to do this myself with your help.

[@geokateflury4103]

Great Job! We have that style Delta faucet in Oil Rubbed Bronze, and it's be working for over eight years. I contacted Delta to check which cartridge I needed, and they sent me one for free. I agree that showing the cut-offs under the sink is a good idea. Also, I read that it's good to flush the supply lines when you change the cartridge.

[@howardlenzer7549]

Well done - it's funny how if you haven't seen how to replace the cartridge in these units the job seems a bit intimidating/impossible - but a brief helpful tutorial is great - just what i need to get the job done - thanks a bunch.

[@Deee423]

You’re amazing!!! We’ve been living with the faucet dripping like this for way too long and I was able to fix it in 30 minutes! Thank you!!!

[@DirtFarmerJay]

Glad it helped, Dee! Best, DFJ

[@kimberlydaniels209]

Excellent instructional video. Thank you for taking the time to put this together. Often times I surf the internet to find "how to videos" and rarely do I ever comment, but its high time I give praise where praise is due. Thank you again and God Bless!

[@DirtFarmerJay]

Glad it was helpful, Kimberly. Thanks for watching and writing! Best, DFJ

[@kathrynmcdaniel9679]

Your video was great. I followed your instructions and replaced the cartridge with 100% success! Your video gave me the courage to try it myself!Total cost $37…Thank you so much!

[@DirtFarmerJay]

Excellent, Kathryn! Glad to be of help. Best, DFJ

[@laurenplaza1700]

Excellent Video and tips. I was able to fix my sink in about 45 minutes. No more leaks and thanks to the Dirt Farmer for his guidance.

[@DirtFarmerJay]

Excellent. Glad to hear it!

[@marcsparber8936]

Thank you so much for making this video. You've made it so easy. I hate plumbing but I followed your steps and everything works perfectly. Now. I subscribed for your videos. Thanks again

[@advicemaster1365]

Thank you! Went to Lowes, got the right part, did the job in 15 minutes!

[@DirtFarmerJay]

Advice Master, our pleasure. Glad to help. Be sure to visit our website and store as well at www.dirtfarmerjay.com! Best Regards, DFJ

[@StingFlight]

Excellent job with the video, including good sound quality for the severely hearing impaired! Carry on!

[@DirtFarmerJay]

Glad you enjoyed it!

[@vickiabbott3838]

Just got a new Delta faucet back in August similar to yours. The single handle is already so stiff, I can see the base flex, plus, it usually doesn't turn the water off on the first try. I have to turn it off and bring it down straight. I got a new, free, replacement cardridge from Delta. I think I'm going to attempt this myself rather than have another charge from the plumber. Can't believe you got 10 years out of yours! I'm hoping this new one is better, but my gut tells me it's not gonna be.☹

[@NAM-qv3ou]

Nice easy guide for Delta Single handle kitchen faucets. Great job. It works. Let's hope it stops the big leak we had in the kitchen.

[@DirtFarmerJay]

Fingers crossed here, NA M! Let us know how it turns out there for you! Best, DFJ

[@carolynkjerting9100]

Fantastic video! You made me not afraid to start this project and it seriously took 5 minutes! No more leaky faucet! Thank you so much!

[@DirtFarmerJay]

Wahoo! Viewers like you are what makes our day. I'm glad you were helped by this video. Keep watching and writing! Best to you, DFJ.

[@AdamMayor]

Great video thanks! I watched another video that had the handle and cartridge on the side of the faucet and while similar, was just different enough to cause me a little confusion. I was very glad to find your video as yours is identical to mine (except the color). I got almost 6 years out of my original cartridge, but the replacement is working great. I picked it up at Home Depot for $35. No more leaky faucet - thanks again!

[@DirtFarmerJay]

Awesome Adam Mayor. Glad we could help you to "Just Do It Yourself". Keep watching and commenting Adam. Best, DFJ

[@Niviatab]

Thank you so much for this video; i am so glad i found you. I was about to make a purchase of a new kitchen faucet since it was dripping. The dripping was fixed by changing the faucet cartridge! Thank you, thank you so much! 🙂

[@DirtFarmerJay]

Glad it was helpful!

[@francisphenry]

Great video, I wish I had seen it first. If you call Delta, they have a lifetime warranty and they will send you all the parts to make this repair absolutely free.

[@DirtFarmerJay]

Thanks for sharing, Francis Henry! Best Regards, DFJ

[@princeinflorida214]

Same for Kohler.

[@jrh1068]

That's what I did. I had the model number and a copy of the original receipt (good to keep when a "lifetime" warranty is offered).

[@ShirlyLyubomirsky]

Best tutorial ever. You are an exceptional teacher. Thanks.

[@DirtFarmerJay]

Wow, thank you! Aw garsh. We're glad that we were able to be of help to you. Best Regards, DFJ

[@keninfarinato1177]

Very well done! Clear, concise, and just what I needed to quiet my sink and all the complaints about it! Thank you.

[@DirtFarmerJay]

Glad I could help Ken Infarinato. Keep watching and commenting. Best, DFJ

[@darylslegh7946]

Wow! What a great video that explains every step so well. Made an intimidating project go so smoothly!! God Bless you Jay!!

[@DirtFarmerJay]

Thanks Daryl Slegh. Glad we could help. Best to you, DFJ

[@ashleymoore6067]

Thank you so much for this video! I’ve never done anything handy before, but I was able to follow your easy instructions and fix my annoying sink fast! Such a huge relief.

[@DirtFarmerJay]

Ashley, glad it was helpful! Best, DFJ

[@colleenmclaughlin5732]

I got the filter off, cleaned. Replaced going to the right. Whoops now it is leaking . Lord I miss my husband. I guess I will wait till my son in law comes to town. He will be in town Thursday. Thank you for your input.

[@DirtFarmerJay]

You got this! Colleen, thanks for being one of our viewer family and taking time to write. Sorry for your loss as well. Best, DFJ

[@wellersco]

This video was super helpful! Got my faucet fixed in no time. Thank you!

[@DirtFarmerJay]

Kudos to you Kelly Valdez for successfully taking on the repair. People like YOU are why we do what we do! Best to you, DFJ

[@happyhomeprojects]

Thank you, your input is greatly appreciated. You've helped us grow over the years and we look forward to more videos.

[@DirtFarmerJay]

Our pleasure!

[@martinschulz9381]

Well explained. I just needed a little refresher coarse.

[@mgbursell449]

GREAT video, short, detailed, and easy to follow. Thank you !

[@DirtFarmerJay]

Glad you enjoyed it!

[@billhayes6743]

Great helpful video. Easily learned how to replace cartridge for similar Newport Brass faucets. THANKS

[@DirtFarmerJay]

Glad it helped! Thanks for watching and commenting. Best to you. DFJ.

[@bruceclark4430]

Good video. Fixed that drippy faucet in no time. Thanks.

[@DirtFarmerJay]

Excellent!

[@evaravenwood1283]

EXCELLENT STRAIGHT FORWARD INSTRUCTION! Thankyou DirtFarmer Jay!

[@DirtFarmerJay]

You are quite welcome.

[@user-ix7sv2lk8i]

Great tips! Just don't drop the little tiny handle screw! We tried to tighten the handle for the longest time and couldn't figure out what was wrong! LOL It was missing that itty bitty screw! Thankfully, we found it in the sink

[@DirtFarmerJay]

Thanks! Glad you found that missing critical part. Best, DFJ

[@dawnmcmillion9077]

Super helpful! Just saved us a bunch right before Christmas. Thank you so much.

[@DirtFarmerJay]

You are so welcome Dawn. We appreciate that you took the time to leave us a message. We love to hear from our viewers. Glad we were able to help save you time and money.

[@212bag]

Great video. I was unsure about the hot water limiter control, but you cleared that up. 👍

[@DirtFarmerJay]

Glad it helped, Bill. Best, DFJ

[@adamread7507]

Thanks for teaching me these new skills, sir.

[@kasperaquatics]

DFJ, thanks for all the great and informative information that you share. We really appreciate your knowledge.

[@DirtFarmerJay]

I appreciate that! Thanks for taking time to write. Best, DFJ

[@RobertBallMagician]

great video. I have one on the angle next to the faucet spout. It is a little tricky, because it goes in on an angle. but my second try I finally got it.

[@superdobette]

And may I add to this video, if you are the original owner of your house they have a lifetime warranty, Delta do stand behind their products. You call them or in my case I sent them an email and they ship you one for free. With crappy shitty water that I have in 9 years owning my house, I'm at my third one that I have to change because it's dripping again. Great product I swear by Delta products.

[@MollyHanmerTheMidnightTokers]

Great video, thank you. Took me hours just to get the calcified pieces apart!

[@DirtFarmerJay]

Wow! Good job persevering until you got it fixed. There is something very gratifying about "just doing it yourself". Best, DFJ

[@cindysipes9130]

Hi. Any tips for getting the calcified joint loose?

[@MollyHanmerTheMidnightTokers]

@@cindysipes9130 I don’t have a magic solution sadly. I tried vinegar, decalcification fluid, hot water, and tapping on the rim. In the end I had to have a friend hold the base of the handle with one wrench (to avoid twisting the base and damaging anything underneath) while I twisted the handle with another wrench. Took two grown women and a LOT of elbow grease! Good luck, it takes persistence.

[@patrickmannion4952]

Thank you for posting this. I had some difficulty getting the handle to come off. I ended up loosening that screw to the point of it coming completely out. Ended up getting the handle off, did the switch-out, but found upon putting it all back together that the inner threads on the handle were damaged / stripped. I couldn’t tighten it back up. Really pissed off.

[@patrickmannion4952]

Finally found the right groove. The casting on the inside of the handle was not flawless, so the threads were not perfect

[@DirtFarmerJay]

Patrick, sorry to hear of the challenges you've had with this. I got your follow on message as well. If you still need to work on this, reach out directly to Delta and tell them what is going on. They generally warrantee all the parts and will send you new items at no charge. Let me know how this all ends up. Thanks for watching and writing! Best, DFJ

[@lkc3061]

Well explained for a novice to follow.

[@wlovett4]

Great presentation. Clear instructions, well organized, pleasant presentation. Kudos.

[@DirtFarmerJay]

Thank you kindly! Did you actually replace your faucet cartridge or just watched so you'd know how to do it when the time comes? Glad you watched and thanks for commenting. Best to you, DFJ

[@JohnBogner]

Remember the set screw cap

[@DirtFarmerJay]

Thanks!

[@TimothyMammenga]

Thanks for the great video.

[@DirtFarmerJay]

Glad you liked it!

[@alanbrinton4659]

Excellent video. It was as simple as you made it look. Thanks!

[@DirtFarmerJay]

You're welcome, Alan. Thanks for watching and writing. Best, DFJ

[@joestewart8914]

In a condominium building the hot water supplied to your apartment may come from a water heater that services the entire building. This is where you must pay extra attention to the limiter switch on the faucet replacement valve. Why? Because the water in such a system is required to be very hot in order to prevent the development of bacteria in the system that can cause disease. Limit the temperature of the water being discharged from the faucet to prevent scalding. Simply adjust the switch with the valve joystick set to "hot" prior to reinstalling the faucet control handle.

[@DirtFarmerJay]

Joe, these are some GREAT insights! Thanks for taking time to share them and get out the word about this. I've learned something and that is one of the things I really like about this interactive medium. Thanks again! Best, DFJ

[@tim1778]

very thorough and helpful- thank you!

[@DirtFarmerJay]

Thanks for watching and commenting Tim Wade. We love to promote ways that people can "Just Do It Yourself". Best, DFJ

[@haroldprice1030]

Thank you and KZbin! I thought I was going to have to get on my back and unscrew something from under the sink!

[@eshnirvicks]

Thank you. You saved us a lot of time.

[@DirtFarmerJay]

Great to hear! Best, DFJ

[@stevenw2866]

Thanks. Very clear and helpful.

[@DirtFarmerJay]

Thank for watching and commenting Steven W. Best of luck to you with your faucet repair. Kudos for being a "just do it yourself" person! Best, DFJ

[@howardskillington4445]

Nice job.

[@billbrannon]

Thanks, now I know how to disassemble without breaking it.

[@DanKastrul]

Thank you! Well done video, very clear instructions!

[@Chakri_MSS]

Thanks a lot! It really helped me. Your instructions are very detailed…

[@DirtFarmerJay]

Thanks for watching and commenting Chakradhar Charya M. Did you "Just do it Yourself" on this repair? If so, CONGRATULATIONS! Best to you, DFJ

[@Chakri_MSS]

@@DirtFarmerJay yes sir. I did it myself following your instructions exactly. In fact, I did not have an adjustable wrench so I purchased it from Menards and finished the task. My water faucet is wonderful now. Thanks!

[@gerryalmendares4004]

Simple great!

[@DirtFarmerJay]

Glad you think so!

[@theastewart6721]

Many thanks for a great video. We’ve had a disaster trying to do this. I appears that we are missing parts! Thanks again!

[@DirtFarmerJay]

Sorry you're having such a hard time with this! Guess you'll be EXPERTS when you are finished! Best, Dirt Farmer Maggie

[@theastewart6721]

Thank you! They are sending a replacement faucet so we will be without a faucet for about 2 weeks!

[@jwpettit]

Delta replaced mine free since it has a lifetime warranty.

[@mitchellmanning7887]

Thanks for sharing

[@robdonna1000]

well done dude. Very helpful. Thanks

[@DirtFarmerJay]

Glad it helped, Robert! Best, DFJ

[@shirleysitzlar8074]

Thanks, very nice!

[@sammin8836]

Thank you so much!!! you're awesome👍👏👏👏🙏.

[@DirtFarmerJay]

Happy to help!

[@poriland41]

looks easy but sometimes it is impossible to remove the cartridge retainer cylinder because it was welded in place to the lower plastic casing, maybe because hard water deposits. I recommend using some plumbers grease on the plastic threads before you put back the cartridge and retainer. In my case I had to throw away the whole valve and buy a new one.

[@DirtFarmerJay]

This is some good information. I like the grease idea before installation as this eases removal during service in the future. I use PTFE tape on metal and plastic plumbing threads not only for sealant, but for easy removal later. Eliminates "seizing." Thanks for writing! Best, DFJ

[@JerryAndJulieMusic]

Great video. I recently put up a video on my channel of a Pioneer faucet that we had installed by a "handyman". We purchased it brand new from him for $156.00 plus his labor $85.00 he took out our old faucet and took it with him. Installed the new one it was leaking! He thought he got it to stop. He left that night was gone about 20 minutes then it started leaking again, so I called him back. He came right back. Looked it all over and he figured it to be the ceramic cartridge. So he left and came back the following morning. He installed the part. It didn't leak. Now, it has been in about 3 days and tonight it is leaking again!!!!! Well 3 strikes your out! Or we are. Now we have a new faucet with faulty parts and are out all that money!!!! We just called an actual plumber and we are awaiting for him to return our call. It is really frustrating. Any suggestions???

[@DirtFarmerJay]

If it's an actual Delta faucet, you can call Delta and they will send you replacement parts with no charge. The first place to look is the ceramic gasket. Look at the end of the gasket (that looks kind of like a monkey face) for any debris in it like sand (if you live in a rural area) or for any damage (Like maybe when installing it, the rubber gasket was nicked by the plumber with a screw driver, etc.) If you discover any defective parts, you can order new ones from Delta at no cost. Hope this helps! Best, DFJ

[@JerryAndJulieMusic]

@@DirtFarmerJay Hi Jay, and thanks for your advice. Well, the plumber came out and he tightened up everything that the handyman did. So another $85.00 later we discovered that was all it was. Great it got fixed!! However, the plumber took it upon himself to also tighten other things under the sink and for good reason but after he left my J- Bend that wasn't leaking started to leak. My hubby was beside himself to be out over 300 dollars on two different guys and still have something wrong a leak. So I said that's it and I took it off myself. It was gunked up with hair and other nasty stuff. After cleaning it out I put it all back together and a couple hours later a few drops. That kept happening. So I said we just need a new one. Went and picked up a new J-Bend and I installed it. A small drip so I had my hubby tightened it with his hands and ever since I'm leak free!! 🤪😃 What an experience!! I use to be married to a plumber so I knew a little about it but never actually did it myself but I'm proud that I was at least able to stop that leak. Thanks again for your advice. Now crossing fingers and toes that our bathroom sink stays leak free. When that plumber was tightening things he also went to look at our bathroom too. He turned that hot and cold water valves and they dripped water from both handles. We bought an older home that had a handyman doing repairs. He changed that bathroom sink himself and the left side handle turns the opposite way from the cold. It's always something 🙄 😒

[@christinamorrison7112]

Thanks Dirt Farmer Jay!!!!!

[@hblee88]

Wish I watched this tutorial first. Should have just "replaced" cartridge instead of attempting disassemble/lube etc. (as suggested by 1st watched video - wasted hours). Thanks so much!

[@DirtFarmerJay]

Glad it helped you Harrison Lee. Thanks for watching and commenting. Hope you will become a regular DFJ watcher! Best to you. DFJ

[@calideb4437]

You did a great job teaching us how to change the cartridge on the Delta faucet. I have the new cartridge ready, can take the handle off (turning off the water beforehand). But, I cannot get the brass "nut" to come loose. I've used an adjustable wrench and a cylinder lock. I've been aware to only untwist the nut - no go. Any suggestions what could loosen it? I'm guessing there's hard water residue... Thanks Jim!

[@AndrewDolanABD]

I'm in the same boat! Did you solve the problem? If so, how? If not, what did you end up doing?

[@calideb4437]

@@AndrewDolanABD Hi Andrew, I tried the vinegar (which is a great solution to many problems, ie hard water deposits, plugged shower head holes, etc). But, that wasn't the case. I ended up having a plumber come and even he couldn't loosen it. He ended up having to remove it in such a way that it would be damaged & then replaced. I hope your situation doesn't turn out the same. Good luck!

[@jrh1068]

Same problem, but not resolved yet. I found that Delta has some bonnet removal tips here: support.deltafaucet.com/s/article/Bonnet-Nut-Removal

[@chrisharris4457]

Delta faucets are lifetime warranty and will send you parts for free

[@jdgolf]

How do you remove the faucet handle if the set screw is stripped and in tight?

[@DirtFarmerJay]

John, that can be a challenge, and it may be that you end up having to replace the handle if the set screw and the threaded hole is damaged beyond repair. Of course, try to avoid that. To get the screw out, you're going to have to use an "E-Z Out" (that is a brand name) type tool (it is really known as a screw and bolt extractor) that allows you to drill a small hole into the set screw, insert the EZ Out and reverse the set screw back out. You can search online to find sources. I hope this helps! Best, DFJ

[@aaronvance7372]

I have 978-sssd-dst which is from 2012. The black piece that came off with yours, did not come off separately. It came off with the bonnet.

[@jddeefo1022]

My delta's a bit different. I can't seem to pop that chrome piece that encases the cartridge off. The plastic piece holding it down won't flex enough to allow the chrome piece to pop off. Any suggestions. I think my unit is 20yrs old.

[@ertonski]

LOVED your presentation. Our faucet also has to be in an exact position to stop the drip. My 1/8” Allen was a little loose, and I double checked the size. When I tried to remove the screw, the Allen wrench rounded the opening. I also tried metric Allen’s, to no avail. I tried an extractor, and it too stripped the Allen head. Any pointers on removing the screw? Since I’m not sure how long the screw is, I did not drill into it before I tried the reverse threaded extractor.

[@DirtFarmerJay]

Ernie, sorry I didn't see this sooner. I hope you got this resolved. Sorry to hear of the hassle. Two things. I think I would use some type of rust desolver lubricant to see if you can get the threads of the set screw to release easier. You'll need to drill in about 3/16" to get a grip on the set screw with the screw extractor. Easy does it, so you don't damage the square shaft of the cartridge. Let me know how it turns out. Best, DFJ

[@bradw1261]

I was able to take the top faucet handle off easily enough. But getting the bottom of faucet handle off was problematic. I watched a youtube describing exactly how to squezze the rubber gasket prongs inward in order to allow you to pull the bottom of faucet casing up and off. However it does not seem to work. The rubber prongs are brittle and seem to be breaking off and the housing still won't lift off and over. Any suggestions would be appreciated.

[@jaydavid53]

Hey Farmer Jay! Good video 5 minutes in and you haven't disassembled anything yet!

[@daviddombrowiak3522]

Is the same cartridge used for touch activated faucets??

[@worldreport7490]

Is there any benefit to flushing the system while the cartridge is removed?

[@timniu3478]

#DirtFarmer Jay, Thank you for this video. I watched several different ones to find the faucet that was closest to mine and came across yours which was extremely helpful. Much appreciation!

[@DirtFarmerJay]

Glad it was helpful! Thanks Tim Niu for watching and commenting. We appreciate hearing from our DFJ viewers. Best to you.

[@RogerPack]

May want to add Delta to the title...

[@DP-vp2qr]

I changed out my delta cartridge for a dripping faucet a few weeks ago. It’s worked for a few weeks but Today i noticed the faucet dripping again. Had to open the faucet and had s really strong release of water suggesting a lot of pressure built up. I closed faucet again and dripping stopped. However I also noticed water was also coming under the kitchen sink via hole kitchen faucet was installed. I opened faucet up and tightened bonnet ring around catridge a quarter to half turn or so. Is it possible the bonnet wasn’t tight enough snd water was flowing back under the sink and causing the dripping?

[@Care2WorldBuild]

Getting a different issue. I stalled the new diverter, and water still comes out of the sprayer and handle. The handle won't turn off.

[@imaginejet]

So my plumber apparently did more than finger tighten the brass part. Does it matter if the whole brass part & the black piece underneath turn too? I'm still trying to loosen it to get the brass part off 😮

[@DirtFarmerJay]

You only want the brass retainer nut to turn. You may need to get a medium sized adjustable water pump pliers to grip the bottom portion so you can rotate the top nut off. Be care when doing this not to mar the bottom portion. I hope this was helpful! Best, DFJ

[@kristinboatright938]

When using the adjustable wrench on the bonnet, are you just putting it on the tip top hexagon part or also the part with the threads? I can’t get mine off

[@DirtFarmerJay]

Only the hexagonal part of the brass retainer nut. You may need to get a medium sized adjustable water pump pliers to grip the bottom portion so you can rotate the top nut off. Be care when doing this not to mar the bottom portion. I hope this helps, let me know how this turns out!

[@himanshuvarandani4671]

Jay - my faucets bonnet nut is tightly jammed and won’t open. I tried putting a rag with half n half vinegar/water to soak around it and also tried wd 40. Any other suggestions?

[@Rani15MD]

would the cartridge also cause low water pressure? I cleaned the aerator and that was not the problem, but I still have low pressue?

[@DirtFarmerJay]

Esha, thanks for asking. This is a process of elimination. You have started at the last item in the chain of water delivery, and you'll now need to work backward. It's possible that cartridge is clogged and is delivering a low volume of water. You can remove it, and soak it for a half day in a bowl of vinegar to see if that helps. If not, then look at the shut off valves. Turn off the valves, then undo the line from the faucet to the valve (at the faucet end) put the ends into a pitcher, and turn them on, one at a time to see if you are getting full volume delivery. If you are, the faucet IS the problem. If you are not, then that is a more significant problem. For now, just start here. Another clue is if there is low pressure only on the hot or cold side. Let me know how this turns out for you. Best, DFJ

[@WaxPaper]

Five times, I've replaced the cartridge on this brand. Three times before I repalced the whole thing through warranty, and twice with the new one. I don't know if it's an inherent aspect of this handle style, or if the brand is just terrible, but it's a pain in the butt.

[@DirtFarmerJay]

Wow, I'm sorry to hear of the poor experience you've had. Delta is a mid-range consumer grade product, widely distributed and readily available at big box and small chain home improvement, hardware and plumbing stores. Their ratings are favorable, but from time to time, someone (lucky you!) has a bad experience. I'm curious - do you have problems with any other plumbing components? It almost sounds like high alkalinity or acidity. Yeow. Best Regards, DFJ

[@WaxPaper]

@@DirtFarmerJay Our water is pretty hard. You really think that could be the reason? There's a water softener in the furnace room, I think you have to put salt in there or something. Never used it.

[@jeffmurphree2937]

In your description, it states "Delta provides free replacements." When I click on the link, it lists the part for $47, but mention on it being free. How do I get this part for free?

[@michaelping5835]

I have the same faucet. Do you notice it is difficult to shut off unless you find the sweet spot? Is there a fix for this?

[@michaelping5835]

Just FYI i replaced the Cartridge and it seemed to fix it. I must of gotten a bad one right out of the box since it was included with the faucet. I bought It at Home Depot. Still waiting for Delta to get back to me about a replacement. Thanks for the helpful video.

[@lolasmith8912]

I am having problem trying to remove the screw with an Allen wrench in the handle. The screw are way too tight. I have tried using WD40 to lime away. Yet it’s still not coming off…. Any suggestions will be helpful. Thanks

[@DirtFarmerJay]

Let's see if we can help. First, and no insult is meant here, make sure you are turning the screw the correct way to loosen it. To the right will tighten, to the left will loosen. That's the "righty tighty, lefty loosey" ditty you've probably heard. We are referring the the arc of the of top of the wrench or tool. Assuming you are going the correct way, then I would try getting a can of Blaster® Penetrating Catalyst. You can get it at your favorite big box store/retailer, as well as many auto part stores. It does a better job than WD-40 in breaking loose stuck fasteners. Also, as a last resort, you can insert a allen key into the fastener head, hold onto it with a pliers, and use a lighter to heat up the allen key and transfer heat into the screw. When its good and hot, douse everything with cold water. Sometimes the thermal shock will do the trick. Let me know how this turns out for you. Best, DFJ

[@boston6781]

Hi, I understood the video. But I can't remove the nut that's holding down the cartridge. If I apply too much force, it begins to rotate. Any suggestions?

[@DirtFarmerJay]

Yes, they can really get stuck. I'd apply some penetrating oil spray and get that into the threads of the nut and let it sit for a couple of hours. Try to remove the nut again. If no success, more oil, repeat until the nut breaks loose. Also, be sure to isolate the torque on the cartridge body by using a large adjustable pliers on the bottom portion. Wrap the body with a rag so you don't scar the finish. Then use a tight fitting large "Crescent" wrench on the top nut to loosen. The tight fit will avoid rounding off the nut. Lastly, make sure you are turning the nut the right way to loosen. It's easy to get it wrong. Rotate the nut counter-clockwise/left. Let me know if this helps!

[@Vanguardsman]

DFJ - Is the flow restrictor located in the base that accepts the new cartridge? Thx.

[@DirtFarmerJay]

No, it's a slider on the top of the new cartridge. On the model shown, it's an orange tab. Best, DFJ

[@nicolebuckner516]

After I removed the screw from the handle, tha handle does not pop out, what could the problem?

[@DirtFarmerJay]

Nickole, give me a bit more explanation. Are you saying you removed the set screw from the main handle and you weren't able to remove it? If so, it's likely that there is calcium build up that needs to be broken apart with gentle but persistent upward force. Let me know if I understood your question correctly. best, dfj

[@varnk]

I tried fixing our faucet, which is the same as this one. For the life of me, I could not get that brass fitting to turn off, and I cranked hard on it. I even tried to use a second pipe wrench to hold onto the bottom black fitting. Not sure why it is so hard to turn off. The faucet is only 3 years old. Any advice on why I'm having such trouble getting the brass fitting off? Also, one other thing. That outer decorative cover just twists off. You don't have to pry the tabs to get it off.

[@DirtFarmerJay]

Varnk, thanks for watching our video and writing. That is quite the challenge. As you know, brass is somewhat soft, so lots of pressure can damage it. Is it possible you have a reverse-threaded unit? That's really reaching, but what you are trying now isn't working. Assuming you have a typical set up, the other thing that I can think of is using something like Blaster Penetrating Oil and see if you can get the threads to release. It is strange that your faucet is only 3 years old and this has seized so bad. If you have a lot of minerals in your water, it can really weld things together! Let me know how this turns out! Best, DFJ

[@jrh1068]

Same problem, but not resolved yet. I found that Delta has some bonnet removal tips here: support.deltafaucet.com/s/article/Bonnet-Nut-Removal

[@andrea.rivers]

So probably $35-40 for parts and saving what? $150-$200 for labor? This is amazing and I'm fairly certain I can do this. I have this exact faucet. Hopefully I can find the parts locally.

[@DirtFarmerJay]

Thanks for watching and commenting Andrea R. If you cannot find the parts locally, you can order them from ereplacementparts.com. They carry a huge variety of parts and are fast at shipping to you. Let me know how it goes by emailing me at [e-mail]

[@geristalica-si9jx]

Don't forget to tell people to put back that tiny decorative piece you put in the sink where you covered the drain with a washcloth

[@kristinboatright938]

What is the black thing under the trim package called? Mine is broken.

[@DirtFarmerJay]

I believe you are referring to the mounting gasket. You can get one from Delta - they may not charge you for it. Or, someone like ereplacementparts.com may be able to help you out. Best, DFJ

[@adriennegregorowicz4325]

Help!!! The lever wont come off. Even after I’ve fully removed the set screw. Won’t budge.

[@DirtFarmerJay]

I'm sorry it took so long to get back to you. I have found when things get stuck like this the best thing to use is a penetrating oil product that you can spray in the stubborn area and let it set. The penetrating oil works its way in and lets the parts release from each other. Have you already addressed this issue and got it repaired or are you still grappling with it? Let me know how this turns out for you. Thanks for watching and writing! Best, DFJ

[@dawnenadavidson6948]

Can that piece you replaced also get plugged up causing very low water flow?

[@DirtFarmerJay]

DawnEna - for some reason, this didn't show up until now in the middle of a thread. Sorry to ignore you! Indeed, it is possible to have calcification take place to the level that water flow is restricted. In this case, you could try removing the cartridge and submerging it in vinegar or a citric acid mixture to see if you can dissolve it. It's not a sure shot, though, as the acid solution may not get into the areas that affected. Let us know how this turned out. Best Regards, DFJ

[@SomeKidYouHate]

@@DirtFarmerJay I watched your video because I couldnt figure out why my sink had low water pressure. Followed your video, took the old cartridge out and submerged it in a mason jar with 1 part vinegar and 1 part water. I gently shook it for a couple minutes, reassembled, and now my sink has great pressure again. Thanks so much for your video.

[@peterexline]

I cannont unscrew the vrass at the top of the sheath holding the element

[@DirtFarmerJay]

Make sure you are turning it counter clockwise and maybe some WD40 or Blaster to lubricate the threads so it will let go. Best to you, DFJ