design a single angle section for a tension member of a roof Truss to carry a factored tensile force of 25 kn the effective length of member is 3 meters
@juhisingh76627 ай бұрын
Thankuiu souvh sir ❤❤❤
@civilworld7 ай бұрын
You're welcome
@saheb_kurkure2 жыл бұрын
👍🏻👍🏻👍🏻👍🏻👍🏻
@civilworld5 ай бұрын
👍👍👍👍👍
@CVBEAAhmadAZEEM10 ай бұрын
why u subtract bolt hole dia in calculating Lc in beta value as u not did in previous videos. Pls clear this doubt
@civilworld10 ай бұрын
Because already we calculate the length and the bolt holes are in circular so that I subtract the value. Which is helpful to reduce the cost. Think in a practical way
@banothakhila26242 жыл бұрын
super sir
@civilworld6 ай бұрын
👍👍👍
@UdayKumar-th5oy2 жыл бұрын
How u take ultimate tensils stress 400 ... In this prblom... 🤔
@civilworld2 жыл бұрын
By using IS Code 800:2007
@Sharafat001 Жыл бұрын
Sir how to provide the edge distance? (40)
@civilworld Жыл бұрын
If it is machine made plate it should not be less than 1.5 times the hole diameter if it cutting edge or sheared 1.7 times hole diameter
@s.t.h.jcreation3344 жыл бұрын
Sir 12.7-r value in steel table I have not found that plz tell me in which page and table no that will be help us to found him .
@civilworld4 жыл бұрын
There are so many steel table books are there you can take near by value which you referred the steel table.
@s.t.h.jcreation3344 жыл бұрын
Yes sir but in steel table that radius of gyration ISA 90*60 value in r- 12.7 but ISA 100*75*8 r value in unequal angles I can't found 12.7 so IAM confuse that value in ISA 100*75*8 -r in another value .ty so much sir for replying me and sir clear my doubt I am so confused
@civilworld4 жыл бұрын
@@s.t.h.jcreation334 Actually it’s a practical subject so many values and formulas were developed practically. Thanks for watching and supporting my channel
@s.t.h.jcreation3344 жыл бұрын
Yes sir I am so glad for you thanks for solving my problem .but sir can I use this 15.9 value in steel code 100*75*8 .becouse it's value188.67
@civilworld4 жыл бұрын
@@s.t.h.jcreation334 yes you can take 15.9 also.
@bharathreddy18453 жыл бұрын
Sir how we will get ISA values?
@civilworld3 жыл бұрын
Refer steel tables book
@bharathreddy18453 жыл бұрын
@@civilworld page number?
@civilworld3 жыл бұрын
You just go through Angle sections page ISA will available
@KAAO-zc8tc3 жыл бұрын
Least radius of gyration value for ISA 100*75*8 is15.7 sir but ur using value is 12.7 sir y
@civilworld3 жыл бұрын
I'm considering the minimum value
@KAAO-zc8tc3 жыл бұрын
OK sir tq
@blessysugunagodsservant44873 жыл бұрын
What is d sir
@snehabr5929 Жыл бұрын
Before uploading a video make sure everything is visible!
@civilworld Жыл бұрын
Thanks for the feedback, please let me know which part of the content is not visible to you.
@rajeevsorokhaibam14504 жыл бұрын
In question it says, effective length is 3m.. What does that imply??
@civilworld4 жыл бұрын
3m is the Length of the member. Which is used in calculation of deflection
@civilworld4 жыл бұрын
By referring steel tables book sp 6 we will get the thickness value
@him_diaries_073 жыл бұрын
Sir, Plzz provide pdf of it
@civilworld3 жыл бұрын
Sorry actually I don’t have it now. Anyway send ur mail I’d if possible I will do.