DID I MESS THIS UP!! P42 BUILD

[@davidpugh6495]

The traditional family is very important. There is nothing better than watching your children play and grow.

[@aaronpowell4885]

Guess I've never put two and two together, I think you're right about big stache Al😅 Most of your videos I watch on the couch or in my room with full concentration. I'll be honest, was working on a saw in my shop while watching the last video and totally missed the potential problem! Mighty fine solution👍🏻

[@jimyeske8498]

When I rebuild Stihl blowers, I triple-stone hone the cylinder. The hone time is dependent on the condition of the walls. Once I have the engine reassembled with quite a bit of assembly lube, I squirt a bit of oil down the plug hole, then I spin the motor with a 13mm socket numerous times, increasing the speed a bit each time. I do that several times before reinstalling on the blower frame. I’ve had great success with that! It’s partially broken in before it ever sees a spark plug.

[@bigmoustacheal3295]

Thanks for the kindness, Tinman. I do appreciate your knowledge and your ability. Thanks for sharing. I can feel it in my bones that I will port a saw someday. Thanks!

[@longbar105d]

Love the saw shop! I spent the morning talking to Mark at Soupakoolsaws about pipes. He had nothing but good to say about ya buddy!

[@doglegjake6788]

Thanks for sharing another excellent video 🙌

[@randymorris8371]

Great video cant wait to this saw run, I think it will run great thanks for sharing!

[@EricaMTB]

You should wing the boost port to flow the mix to both sides, not over the top of the piston. Compress the depth as you open the width.

[@thebradleysoncatbirdhill6849]

The professor at his finest!!!

[@mattw5729]

Great teaching with saws and life! Thank you Sir.

[@martyrutter3630]

Some fancy work will be interesting to see the final product. 👍👍

[@wrstew1272]

Aircraft do commonly use Brass buttons on wrist pin. It absolutely contains the gudgeon pin in the piston. Circlips on yours keeps it out of the ports 😊. I thought immediately about that, if you have lathe, easy fix. The metal that you might have effected is minimal, if you kept it that quick, no way you could ruin the load area. Done deal, let er rip!

[@snowysnobdds7842]

A boost port most definitely helps. 👌

[@tomintexas817]

Thanks again for all the info Tinman😅 And I got a 046 red lever it has a little porting but seals are trash and piston skirts are shiney so I got a project for $150😊😅😂

[@aldredske6197]

Hi Tinnman!😀😀 How did you know that I have a big mustache. LOL!! But I also have the ZZ top beard to go with it. Take care buddy!!😀😀 Logger Al

[@wrstew1272]

I would have, but SheWhoMustBeObeyed whines and bitches till I trim it 😢

[@tinmanssaws]

Cause your name is Al? Lol

[@wrstew1272]

73 and have had a reasonable mustache since 1968……Randy is the common name but my friends call me Whiskers😮 😊

[@tinmanssaws]

Lol

[@rncboy2]

A guy might want to ad another plug in the wrist pin on the exhaust side as well to keep the weight a little more balanced. A thought not 100% sure that's even gonna effect it much though. Yeah it being 1 gram difference it might not effect it having that much more weight on one side of the piston

[@doglegjake6788]

That dude has the funnest job on planet Earth 👍

[@doglegjake6788]

When I'm at work , I usually have two speeds .. Stop and Reverse 🙌

[@doglegjake6788]

We are Definitely learning from the best of the best

[@KensSmallEngineRepair]

“Like sands through the hourglass, so are the Days of our Lives”

[@cynthiahoekstra7212]

Elegant solution

[@camrynrhodes798]

Thanks again Mr 👍

[@fixinanddoinstuff2134]

Just picked up a Sachs Dolmar 111 today. Winter list lol

[@tdawg8605]

Play the game take the educated chances and build a monster. TC Mahalo Tinman 🤙🤙🤙

[@fhkqdude]

I assumed you were going to run a stuffed wrist pin, I've had older saws with stuffed wrist pins and mopeds, I would only cork the exhaust side

[@wrstew1272]

A six by eight foot bump out would accept a mid sized lathe, but a ten by twelve foot one would get a big un in! Framing buddy, easy peasy 😂

[@michaelwhiteoldtimer7648]

Can’t wait to see this saw running

[@shapeshifter7753]

Ya! QD! Canada 🇨🇦 💪

[@geoh7349]

put a teflon button in the piston pin. vw guys used to do it.

[@jeffdillard8789]

Machine a little plug out of aluminum and press it in the pin on the port end

[@joebaldus3572]

Beauty. Would it be much harder to turn one from scratch? Thats what i was thinking.

[@tinmanssaws]

That's an option if a guy knew what material and how hard it would need to be to not fail.

[@GarfieldCunningham-t6z]

Do you match the transfers on the piston to the saw body as they're wider then the piston?

[@matthewewing663]

BMA….true!😂

[@marcustraber]

I got an xl76 and it came with a little red barn piston with a hollow pin. Do you happen to remember if the oem pin is hollow? Thanks in advance.

[@tinmanssaws]

I can't remember I'll have to check am old video

[@tinmanssaws]

I looked at some old vids, that model has open ends on the wrist pin .

[@marcustraber]

@ wow thanks pal! I was looking at some of your 1000 sub days trying to beat you to it.

[@JohnBrunner-ym6qj]

Yes big stash is Al here in mass

[@jasonsnagel]

I wonder if a teflon button could simply be pressed in the pin tight

[@jasonsnagel]

Mainly because if pressed all the way to the center of the wrist pin it wouldn’t throw the balance off the piston

[@kurtsteele5587]

How's the Tinman and family

[@danschuckers5281]

dan from pa. not al