Will Dad's Favorite Tractor Ever Run Again? Part 1 Installing The Crank Shaft and Mains!

[@garethstott]

'Now Mom don`t be yelling at dad about this' 😂😂

[@seancombs499]

Like how Dad is letting all you guys be involved in putting it back together. Like ya said you two have done a lot on them ole two cylinders dad can prob put it all back in is sleep lol. Glad to see it going back together bud

[@peteschiavoni]

So happy to see dad’s baby going back together. A full resto will be great.

[@garybarrett6581]

wish l could of ran into you at Rantoul We had our D17 D there plowing!!! l will be watchin!!!!

[@randybedker1584]

When you work as hard as you guys do you gotta have some fun with all your money..😂😂

[@jazzerbyte]

It will all be worth every penny in the end when the old iron is in top tune!

[@garethstott]

Great to see you passing on the hands on experience to the next gen.

[@Spitter-ud8jd]

Torque spec. on a John Deere 720 main bearing is [German] which = Goot n Tight.🍻

[@roberthocking9138]

LOL I loved the red hand painter 😂 , well done guys. For a minute there I thought you were putting it in without assembly lube 😬

[@jonathancrissinger2301]

Thanks for explaining the various things about the little parts and pieces. It makes it more interesting to watch.

[@danw6014]

$4,000!? Don't say that. I've got a 730 diesel waiting for a complete overhaul. One thought I had for setting the crank in place without marking up the journals. 3M vet wrap would protect them without leaving any adhesive behind. The other thing I like to do is use aviation gasket maker on the gaskets. I put a very thin film on and I think it seals any deformities in the metal plus holds the gasket in place because it gets tacky after a few minutes. Just my $2.00 because two cents won't buy bubble gum anymore. Great video. Can't wait to see the rest of the series.

[@georgejones-nz1qg]

If you make a serious crop, you've about got to overhaul them old popping Johnnies every winter.

[@charlietanner6211]

gotta love them to put that much in one

[@tylershumaker4152]

Glad you were happy with the crank shaft. That had some of the nicest splines, I've seen on a diesel crank

[@wademizelle3433]

Great video, a lot of old timers watching. Can’t wait for the next one. Thanks

[@dirtgrainsteel]

Glad you enjoyed it thank you!

[@CaryGuyer]

Very well presented and detailed how to video on that particular process. You will have that thing running like a top when complete.

[@garymessina1609]

Great job great video thanks Brandon and George and dad and Tyler

[@johnnyholland8765]

That tractor is worth spending the money on. The rest of it is in good condition so yes. Beside your Dad has to spend his money on something for fun. His hobby just happens to be a somewhat expensive one. Just look at it as another farm repair...

[@79fordblake]

Glad to see it's going back together!! Send the pumps and injectors to Garry Power. :)

[@dirtgrainsteel]

That's exactly where they are going!

[@jeffkluesner1895]

I’m glad to see you are fixing that tractor too good of a tractor to part. I have an early model here in Iowa I would fix mine if that happened to me good luck and keep up the good work

[@brittblanton8342]

Great video Brandon, nice to see how it’s done 👍

[@oldamericaniron5767]

When working on something like that it isn’t a question of will it run again, only when.😀 I had an old friend who would say, we don’t ask it we tell it.

[@artillerest43rdva7]

great to see progress on the tractor! keep up the great job.

[@phud9657]

👍👍

[@LloydKincade-x9s]

Why didn’t you guys put a coat of oil on the bearings while installing them and torquing them down. They’ll be spinning dry till the pump gets oil to them. Maybe you did oil them but I didn’t see it being done.

[@dirtgrainsteel]

Everything got white grease...we also will leave the fuel in the stop position and turn the big engine over with the pony engine to produce engine oil pressure before we allow the big engine to start and also before I put the top plates on the crank case I dumped oil down on top the crank trust me it's good and oiled up in there before it even fires lol

[@scottreasoner6126]

Did you ever find out what caused the old crankshaft to snap in two. What if the new crank does the same thing.

[@dirtgrainsteel]

Come to find out it wasn't to un common for these cranks to bust even back in the day when the tractors were new....I've heard several reasons as to why they break number one reason the most popular reasons is lugging the engine for long periods of time which we never have but that's not to say some one didn't do it years ago and started the problem....this is a little bit newer crank as far actual build date so it probably won't be a issue ever again

[@dp8689]

Fifty foot pounds on center maine

[@dcw1540]

Any idea what made it brake?good luck.😊

[@CharlesEiker]

I was always told not to touch rod bearings with your bare hands, always use rubber gloves. Just what I was always told maybe it was bull.

[@dirtgrainsteel]

I've never been told that on engine bearings I was always told not to touch the sealing surfaces on ring seals for excavator and dozer final drives

[@rudycarlson8245]

Did you end up doing a complete engine rebuild on this tractor? What happened to it?

[@mikevaske8255]

If you are so concerned about not damaging the crank, turn your knife over, cut up, away from the crank.

[@BryanJ.Covert]

Brandon why did you throw your father under the bus by bringing up the price of that crankshaft , if you were married you would know a happy wife could be a happy life . Better luck next time dad !!!!!

[@michaelisrude]

Does it help sticking your tongue out when tightening bolts?lol

[@dirtgrainsteel]

Lol yes!!

[@bryancovert9821]

Why did you though your father under the bus ? We know that type of things are expensive .

[@scrotiemcboogerballs1981]

Glad you got the parts you needed thank you for sharing It sure was easy taking it out when it’s two pieces lol

[@Bill-xc8le]

You not putting assembly lube on those bearings?

[@dirtgrainsteel]

White grease on everything