DIY Basics - 1ch dc 5v/7-32v Relay Module switch + clean NO/NC contact eWelink - Alarms/ relays etc

DIY WIFI 1ch dc5v/7-32v OWSOO Relay Module switch with clean NO/NC contact works with eWelink app . Link to schematics below.
You can control anything from an alarm to a gas heater !
Please like and subscribe if you like the video, thanks for watching.!
Links below to some of the products i used in the video:
►Heschen 22mm LED: amzn.to/3dlDNqU
►1ch dc5v/7-32v Relay Module: amzn.to/3bhY4fQ
Link to schematics:
►ibb.co/Jmr9Y0S
►ibb.co/tLhKpPC

[@royzamora8122]

Master! Your model and explanation was crystal clear Thanks!!!

[@leonline3424]

my pleasure

[@olddanb1]

Hi LeOnline. Excellent info, thanks very much. But I'm still confused. Can this device go in line on the negative side of a 12v battery to dissable a running generator engine? Or could I fit it in series to disable the fuel pump so that the engine runs out of fuel and stops that way? This is a stopping event that i want to create. Not a starting one. Thank you.

[@siwoprabowo589]

what will happen if my input gives 12v ac voltage?

[@marionichilo7531]

Hi. do you know if there is a Bluetooth one. would like to use it on my van for a simple alarm. one side when doors open the horn goes off. thanks

[@johnnyboy0069]

Will this work with a 5 volt feed to the 7-32 v terminals. ??

[@martinlawes1]

Can I control 12v leds with this and which 2 connections would I use, thanks Martin

[@massshah]

where is that brown wire going to

[@olegdasha6518]

How many remotes can be connected to that switch??

[@randallharley6567]

Maybe show me how to pair it😮

[@succduc]

If your one is not pairing try an older phone. My S23 ultra did not work so I used a S9 instead and it worked. Also try going into pairing mode in the app the open your WiFi settings and refresh then go back to the app while it's trying to pair and it'll eventually find the device

[@JoaquinRaggio-bu2kn]

it works only in the local network or its possible to control through internet out of the network?

[@MrBobWareham]

Very nice sort of Sonoff ish then! that would be good to turn off on the bench power supply or lights

[@leonline3424]

Hi, yes, there are no limits to what you can use this device for , thanks for watching.

[@whocares8770]

Got same module. Has power, connected tonapp, can control. But device does nothing. I've tried all 3 contacts. Device works fine direct to battery.

[@leonline3424]

if you mean on the clean NO/NC no problem, that's why it's called "clean", you pass any voltage up to 220v.

[@jcody7936]

i subscribed just because this video was EXACTLY what i needed. thank you! i wonder if the wiring is the same for a 2 channel

[@leonline3424]

Thanks, yeah in the end it's just another channel so you just replicate the first one, get the power from the first contact too.

[@MsVincentC]

Hello, Very useful video and I even recommended it to a few of my acquaintances. But I have a few questions - I hope you will be able to help with the information. 1. In addition to controlling the AC 10 A, can something of the order of 12-24-32 V be output at the AC/DC output? Your example is currently with 220v 10A AC. 2. Where there is an input DC 7-32V only for the power supply of the board and does it serve or then the power supply that we have supplied in "imput DC 7-32V" can come out in the output? Thank you in advance!

[@leonline3424]

Thank you ,very much appreciated :) You can use any voltage on the contacts. I hope i understood your question, i'm sorry but did not not understand the second question.

[@andrewtremblay5697]

If I was to power a 12v LED light through this where do I plug the wires into?(

[@leonline3424]

In the description you will find the links to the wiring schematics ;)

[@touchlessgatessrinagar5408]

How to connect to google siri or alexa please make a video !

[@enghamedhamdy6670]

How much is it now , can you send it to Egypt 😊 thanks

[@burnjack291]

Can this be used with a 12v house led light number? To turn on / off (address number on the front house)

[@leonline3424]

Hi, sure,why not ? :)

[@dhky81]

Can this method be used to switch between 2 amplifers that are connected to one set of speakers or will it burn out?

[@leonline3424]

Hi, would you be swithcing the amps off and on? Beware that this has 2 single contacts, but one would be open (off) while the other closed (ON) and viceversa!. I don't think it's suited .

[@kbalabha]

The eWelink app does not recognize the device even when connected to a 2.4Ghz WiFi

[@emanuelortiz3667]

Can I use this to turn on and of a DC motor with a timer option?

[@leonline3424]

Hi , you can control anything but for the motor you should use a high-current load contactor controlled by the open/closed contact similar to this one in the following video link: kzbin.info/www/bejne/b5C4p3udl9OlqZY

[@oc8382]

I have nice rox600 slising gate. Can you please check on it manual where i have to connect Com and NO contacts there?

[@leonline3424]

9 Com, 12 NO

[@oc8382]

@@leonline3424 your are star! Thx a lot. And to power switch up from same Nice, What i could use ?

[@leonline3424]

@@oc8382 what do you intend for "power switch up from same Nice"? sorry but i'm not sure if i understand what you want to achieve :)

[@oc8382]

@@leonline3424 to take power for the switch, can i power it from gate motor nice rox600? I mean 9 cpm, 12 NO for a switch to communicate with gate, but which port from nice rox600 to use to get power for the wifi module?

[@laserfalcon]

Can the switch give info back to the app if something is on or off?

[@leonline3424]

Hi, yes, with the eWelink app you can control the device ,check if it's on or off ,and create scenes.

[@karanbhullar559]

Hyy . I want use wifi switch for 90 amp self start generator

[@leonline3424]

you need a contactor , you can use the Relay Module in this video to turn on or off the contactor or do something like in this video: kzbin.info/www/bejne/b5C4p3udl9OlqZY

[@dirkkerckhofs4781]

Mine acts as a puls, it stays on for one second and then turns off, can i change this?

[@leonline3424]

you have to change the mode with the tiny push button, if i'm not wrong (time has passed i can't remember) ,it has 7 modes to choose from.

[@Anth78p]

How many amps? Could I use this to turn on off just a 12v 160w fan? :)

[@leonline3424]

Just a 12v 160 w fan? go for it, it will hold ;)

[@Anth78p]

@@leonline3424 Tnx a lot for yr reply. Basically, I have 2 fans, 12v-80w each. These are connected to a 220v->12v power transformer. I need to make them "smart" and go on/off according to a smart temp sensor. You confirm me that if I put this relay on the 12v cable to the fans, it will work? if this relay is 12v-10amps, this would give 120w available while the 2 fans together are 180w...it will still hold? or I shall use one relay for each fan? Just to double check. Great videoes anyway ;) Greetings from Wales :)

[@gblueslover8807]

Can the 7-32v board power input be AC and DC both ?

[@leonline3424]

no

[@gblueslover8807]

@@leonline3424 I'll buy a in line rectifier for it then.

[@jagboy69]

SO what is it? AC or DC???

[@paulolemos9085]

Hi man, great presentation! Do you know if it only works with Wi-Fi? Or can it read rf frequency? Example: garage doors

[@leonline3424]

Hi There, no it doesn't have an RF feature, but you should check out my video with the RFR3 from Sonoff, that might suit you !

[@paulolemos9085]

@@leonline3424 will do, thank you very much!

[@fletch5264]

Can these be flashed with Tasmota?

[@leonline3424]

I don't think so.

[@dindigulautomationwaterpro5145]

Hi sir. Mobile App is free of cost to use long time?

[@leonline3424]

Yes there is no time limit, there are 2 versions . i reccomend it