DIY Brushless Motor Controller 40A ESC BLDC Module using MosFet IRFZ34N IRFZ44N

[@User_ycTaL]

Огромное спасибо! Собрал по вашей схеме и все заработало с первого раза!

[@S_e_r_g_ei]

Тогда подскажи пожалуйста, где вход и выход в схеме. А то, я не очень силён в электронике.

[@Virigis]

@@S_e_r_g_ei , тут похоже нужно вывести из МК общую точку обмоток и подать на её +.

[@ВадимЛебедев-ь5ъ]

Соединение звездой ?

[@Virigis]

@@ВадимЛебедев-ь5ъ , пожалуй так, но не надо вникать в назвние.

[@User_ycTaL]

@@ВадимЛебедев-ь5ъ Да, звездой. Мультиметром ищете общую точку (к ней идёт + питания) и к остальным 3 выводам провода со схемы.

[@wonderwang1585]

backside wiring of PCb is absolutely eye blinding. It makes one crazy

[@djemaiabdellah1240]

Hello, when I posted the video, I needed an explanation, and it was a little thank you

[@ryanbi]

Great man ! Very GOOD Man !

[@ErCanEverything]

Thank you very much🙏🙂🤝

[@SpinStar1956]

A helpful hint for you videos: if you will smear a very thin layer of SMD flux-paste over your solder board (not so much you fill the holes) and all component leads, you will get much quicker wetting of the solder to the connection. During a normal solder operation, you are actually oxidizing the connection because of the elevated temperature, and the solder balls-up waiting for the solder’s flux to heat up enough to become active to overcome that oxidation. Since the layer is so thin, it cannot be seen. When I make PCB’s I smear them with SMD flux-paste to keep them from oxidizing wether I tin-plate or not. I then usually wrap them in cling-wrap for longer storage. Give it a try, think you’ll like it! Anyway, great video!

[@ErCanEverything]

Thanks for the tip, I appreciate that.🙂♥️🤝 I ordered such a solder paste but have not received it yet. After receiving I want to make a shorts video.

[@timhofstetter5654]

If you're using decent solder, you have no need of doing that. Ersin, Kester, the good stuff. 63:37 or even 60:40. That wets like lightning.

[@gamesnic]

@@timhofstetter5654 There's enough people who use unleaded solder

[@timhofstetter5654]

@@gamesnic Enough? For what? To make it wet decently? News flash: it wets HORRIBLY compared to 63:37. Awful stuff, almost as bad as Archer (Radio Shack) fluxless solder from 1975.

[@gamesnic]

@@timhofstetter5654 Not my fault if you use bad solder. Mine works perfectly fine and fills the solder joint right down through the hole

[@modricamodrica4763]

👍👌 Blagodarim 👍💟💙💗

[@konohabeast]

Just what I needed, thank you so much!!

[@ryanbi]

Thank you from Viet Nam !

[@hosamabdallah2609]

that was a high quality video! I was wondering how only 3 mosfets manage the transition between the 3 phases of the motor, an explanation of the circuit would help, thanks.

[@anonymousXYZ]

Note that he connected to AC power. You can look up AC 3 Phase Induction Motor.

[@chazlabreck]

He's creating some kind of phase manipulations to get the 120 degree difference between phases..

[@abraxasivo]

No way, fake

[@chazlabreck]

@@abraxasivo yeah im not convinced...lots of dudes these days are just getting click bait,, that schematic makes no electrical sens and does not show input or output connections so it looks like it just is going in circles..

[@alerey4363]

holy muscle Batman! I was expecting a hard-drive or DVD brushless motor but you hooked up an electric vehicle even with a wheel!!! 😲

[@rimbang_]

Didn’t expect that too

[@robertonery8358]

De longe o melhor vídeo!!!!

[@ErCanEverything]

Thank you my Friend🙏🙂🤝🤝🤝

[@Tugitu]

Great 👍👍👍

[@ErCanEverything]

Thank you my Friend🙂

[@lex_kirgoff]

It’s cool, thank you very much🤝

[@0dbm]

Beautiful work , prototype is big business

[@FixitEasyDIY]

Great man! So precise!

[@ErCanEverything]

Thank you my Friend🙂🤝

[@ТехноФікс]

Круто 👍👍👍

[@ErCanEverything]

Thank you🙂

[@davman865]

reading the comments and an answer you gave about the red wire you put on the common where the three coils meet and you said you had converted from delta to star... I tell you that these motors are always in star and that for them to be in delta we must separate the three coils and remove them from the common and joining each one with the end of the other you get the delta connection...

[@ElenaShumilina777]

Super!

[@davman865]

leyendo los comentarios y una respuesta que diste acerca del cable rojo que pusiste en el común donde se juntan las tres bobinas y dijiste que habias convertido de delta a estrella... te cuento que estos motores siempre están en estrella y que para que estén en delta debías desunir las tres bobinas y sacarlas del común y uniéndolas cada una con el extremo de la otra obtienes la conexión delta... traducción: reading the comments and an answer you gave about the red wire you put on the common where the three coils meet and you said you had converted from delta to star... I tell you that these motors are always in star and that for them to be in delta we must separate the three coils and remove them from the common and joining each one with the end of the other you get the delta connection...

[@ErCanEverything]

Actually you are right this motor was star type connected, I just added the red wire as common connection. Your answer made me think a lot, but you are right, thank you👍🙂🤝

[@REPUBLIKGAMERS]

Good job Mr.

[@ErCanEverything]

Thank you🙏🙂

[@leonardocavalcantedasilva9422]

hello friend, where can I get the positive wire of the hoverboard motor, this circuit was made for him, correct?

[@ismartalluarjun]

Super excited brother

[@ErCanEverything]

Thank you🙏🙂

[@رشيدحدادة]

Great work. But in the circuit diagram, you did not indicate where the positive is placed and how much voltage please?

[@ErCanEverything]

Thank you🙂🤝 The positive cable is connected inside on common point of this star type motor. The voltage is from 8 to 18V because you have to put zener diodes between Gate and Source

[@رشيدحدادة]

@@ErCanEverything thank you

[@JacobLungu-z9x]

Amazing video I have tried and it worked now my question is why the mosfet get hot?

[@davidmorris-jones210]

Nice job. MOSFETS are great.. I use them in RF applications. So cheap considering the cost of true RF transistors.

[@ErCanEverything]

Thank you🙂

[@rusticagenerica]

How many kind of MOSFETS are there out there?

[@davidmorris-jones210]

@@rusticagenerica I replaced all my 16 (whatever mosfets they were as numbers were removed) as close by lightning static blew the amp, I saw the flashover. I used IRF520N which ended up being better but had a higher biasing voltage. Ones I corrected for the new bias gate voltage it was distortion free. The originals were a bias voltage of 1.5 or abouts as there was only 2,1 volt bias before I changed the appropriate resistors to bring the gate voltage up to 4.2. Amp is better than before now a lower input to get same out. It is a HF RF amp.

[@francogigli5108]

nice job bud! i only have one cuestion, when you turn the pot to the minimun, the power output is off?

[@RadioGubitel]

Is it possible to use any N-channel mosfets? 75N75 for example.

[@ErCanEverything]

Mine are also N channel MosFet's🙂

[@Electronzap]

Nice.

[@stanisawmuszynski8978]

Ekstra,👋

[@aguswiyantomo845]

Thank you ? Input was 12 v dc ?

[@ErCanEverything]

8 - 18V

[@biocargo]

muy interesante amigo, tienes un nuevo suscriptor, voy a probar de poner un PWM de voltaje como fuente de alimentacion y arrancar en 8 voltios. abrazo.

[@ErCanEverything]

Thank you very much🙏🙂🤝

[@Ironboyhight]

Dose it work 5v to 48 v sir

[@johnhopkins6260]

40 A no heat sink?

[@cufe2741]

hello thanks for the video, can you also make one with 80A or at least 60A (for continuous operation)?

[@anastashskal6652]

You can probably make it your self by using higher rating components, but am not sure gow efficient will be

[@MacgyverSiruma]

is that red wire from motor a nuetral winding then suplied positeve and to the board is negtive?

[@awesome3mpire405]

nice job!!! i have one question, it can go backwards?

[@DIOS-M]

Are hola sensors installed in the engine or is there an additional controller?

[@ErCanEverything]

Hall sensors are in place but I have not connected them and there is no additional controller. But I connected 1 extra cable to a common point of the three cables, this red cable goes inside the motor and is connected to a common point and that's.

[@DIOS-M]

@@ErCanEverything Do I understand correctly that transistors give a phase shift, in fact they perform the function of a hall sensor?

[@ErCanEverything]

The transistors are lined up with the help of diodes and resistors and thus the motor starts to rotate

[@DIOS-M]

@@ErCanEverything Thank you, a useful thing

[@ErCanEverything]

Thank you🙏🙂

[@JoseRomero-or1if]

На каком напряжении он работает или какие напряжения он может выдерживать?

[@jorgeacosta1198]

hola exelente elvideo de montaje voy a hacer el circuitopara ver si funciona por que lei muchos que no creen y no esplican por que ademas pretenden manejar un auto electrico o jumbo jet con un circuito de experimmentacion exito y salud

[@Edmorbus]

Thanks for sharing

[@tavomotors9814]

Greetings from Colombia, do you have a diagram or a video to make a 3000w 80A card for a brushless motor that has forward and reverse gear?

[@Alex-silva16]

Sobre o fio vermelho tem que ser dentro do motor ou tem como alimentar o circuito nos mosfet

[@actosDeGuerra]

O fio vermelho é ligado direto na bateria, é a junção de todos os fios da bobina do motor. Sem esse fio não funciona, sendo assim precisa desmontar o motor e soldar um fio pra fora pra ligar o positivo na junção de todas as bobinas. Os três fios que ficam expostos em cores será ligado o negativo que será controlado pelo circuito e o positivo é o centro de todas as bobinas que fica dentro do motor.

[@eeghtitelukintan2948]

wow..great

[@CesarGomez-gd9kd]

Wow, It´s a great project, I have a question ...what kind of motor is? 12v?, it is brushless? it was interesting to know. It have many potential applications. thanks.

[@ErCanEverything]

Was a brushless motor type Delta with 3 cables, but i converted it to a Star type with 4 cables. I connected the red cable inside to a common point of the 3 phases to work with this circuit

[@CesarGomez-gd9kd]

@@ErCanEverything Oh thanks, I appreciate your kindness,

[@el_penco_rd]

Could you please give me some finger plan of that common one? @Ercan Everything

[@FratCan]

Benzer videolarda mosfetler için soğutucu kullanılmış, sizce gerek var mı soğutucu kullanmaya ?

[@victorvictor8311]

A cordless brushless angle grinders have similar to that chip but it's very weak and cant hold much load if you can make one can hold the heat and powerful i think you can make money from that and i hope you make a video about that ❤

[@s-tazipart1750]

Is the input dc or ac?

[@ErCanEverything]

12 - 18V DC

[@serjaocvt9726]

Very Nice 🇧🇷 top ESC motor brushless

[@nhanphanthanh6374]

like this very hot mosfet

[@andrewthuku2638]

The voltage your feeding inn, is it AC or DC

[@PRANJALELE]

Could you please share the circuit diagram. How do you connected the power supply in this circuit?

[@egongunter6589]

Hallo. Könnte man die Schaltung so ändern dass man einen 220 Volt bldc Motor betreiben kann?

[@CristinaSantos-uk2jf]

The hall sensors are functions?

[@ErCanEverything]

Not without hall sensors is connected

[@chrisbullen4317]

New here. Great Video! Looking for a sensorless BLDC 3 phase motor controller for a 12 volt 850 watt motor? any plans / pc boards I can try to build?

[@luiscz777]

Hello, good video, I have a broken hoverboard. Would this circuit work for me to activate the motors in other projects?

[@flbourne1]

And a circuit diagram should include power in, POT and power output

[@isabellenivrose7133]

Thank you for the video my brother , what is the frequency of circuit ?

[@ErCanEverything]

I have not measured the frequency🤷‍♂️

[@isabellenivrose7133]

Okay !

[@isabellenivrose7133]

can you measure it for me ? Please .

[@imnotbeluga007]

Depends on current draw. Higher current will attract the rotor faster, resulting in faster switching. This speed up will continue until friction limits the output speed, and thus switching speed as well. If there wasn't friction, it would keep speeding up nonstop. So, the frequency can vary from a few Hertz to hundreds of Hertz..

[@actosDeGuerra]

Pessoal, falta uma informação importante: a derivação central das bobinas precisa ser conectado no positivo da bateria e para isso precisa abrir o motor, no caso dos motores de hoverboard bobinados em estrela. Caso ligue apenas os três fios do motor só vai ter o negativo na bobina e não irá funcionar. Para funcionar precisa de 4 fios e não apenas 3. Sendo que são 3 fases e na junção do fim de todas as bobinas será ligado do positivo. Este circuito controla o negativo nas bobinas, sendo assim o positivo precisa ser ligado direto na junção de todas as bobinas.

[@katiekumcgil]

Ok i think i sussed it out the red wire goes to the center of the star wiring it has to be added separatly ,but he doesnt tell you that ,it is possible some bdlc motors would require being changed to star wiring arrangement if they are different,

[@katiekumcgil]

this isnt a circuit id recomend for scooter or ebike as it will be extremely noisey ,like load wineing as spinning up,and will be bit jerky and erratic,due to lack of hall sensors for rotor position, but as a fail safe ,it be ok \

[@nsbharathi4402]

is it returns current product

[@robsonnunes2033]

🇧🇷Here in Brazil. Very good your project. How many amps does it support, can it run a washer and dryer motor for testing?

[@ErCanEverything]

In principle, it is possible, but the motor must have 4 cables, not 3

[@erickjuegasv5345]

Excelente video ,,estaba buscando fabricar un controlador de un motor de overboard casero ,,ya que aqui donde vivo no venden controladoras comerciales ,,,y la unica opcion es fabricar una casera como la que muestras en el video ,,la duda que tengo es servira para poder hacer un scooter electrico casero con un motor de overboard ? ,,y la otra duda es cual es el rango de voltage y amperaje con el que se le puede alimentar a este controlador casero ,,agradezco mucho si respondes mis dudas ,,,saludos desde el salvador

[@francescomerlin5371]

How many volts does the controller work?

[@franciscorodriguez-wl9nj]

hola, muy buen video,con que rango de voltaje trabaja

[@suryapatnaik5720]

Can i use 25Amp n channel smd mosfets??

[@ErCanEverything]

Of course, but you have to put a heat sink. If you want them to be more durable, you can connect additional transistors in parallel.

[@ISAACSACKEYEAGLES]

How did you manage to get your power in if it a three phase delta ànd it only three cables coming out as your supply output feed or load, May I know your positive input then ??????

[@MrEmrys24]

how does this work? is it similar to astable multivibrator?

[@nsbharathi4402]

Sir I want some details to this how much volts and amps taken by Multimeter test video to your channel 🙏🙏🙏🙏🙏

[@farshidhz1174]

is it 12V in ?

[@ErCanEverything]

Yes 12V

[@oracid]

Thank you for sharing your work. This seems to be a one way ESC. Would it be possible to make a bidirectional ESC ? Thank you from Paris.

[@ErCanEverything]

Thank you🙂 I'm thinking about it but without a microchip it's not possible.

[@Persanity]

@@ErCanEverything I assume this would mean it can't do regen?

[@imnotbeluga007]

@@Persanity It can't. But it is possible to add a switch that switches the coils from the driver to a separate rectifier, but I don't think it's worth it.

[@군포김tv8017]

good good^^

[@boasnovasonline8764]

Direct from Marituba, Pará Brazil thanks for the video, I would like to know if this controller is the battery or if it is connected directly to the electric grid? I would like you to make a 48 v14 Ah battery model is it possible? From also

[@ErCanEverything]

This circuit works from 8 to 20V

[@boasnovasonline8764]

@@ErCanEverything This circuit works from 8 to 20V but I would like to know if it is DC or DC/?

[@boasnovasonline8764]

@@ErCanEverything I would also like to know, friend, how many amps can I get from this circuit? Would it be possible to move an electric bike motor, for example?

[@ErCanEverything]

DC

[@ErCanEverything]

@@boasnovasonline8764 To drive an electic scooter you need another circuit controlled by the MCU. This is a prototype and will not run at full power

[@Dancopymus]

Hello friend, first of all, thank you for sharing. I have a question: In this type of circuit, every time you turn it on, do you have to give the motor a "push"? Or does it depend on the type of motor, such as HD or CD/DVD ROM?

[@rodrigoserna9712]

hello men, wich is the current voltage? and friend how you take the common point into the motor? many thanks for you

[@ЮрійМакаровський]

Hello, could you help me, I want to repeat your controller, but on IRF1404 transistors, please tell me which circuit components to take in my case?

[@ErCanEverything]

You can use absolutely the same scheme, the transistors are identical, even yours are more powerful🙂

[@rusticagenerica]

Where do you advice to buy those components?

[@AndrejGavriluk]

Выпаять из старого гироскутера .

[@saifmia7797]

Can i use this for 1000kv drone motor....?is it works well for this..?

[@markanthonycaintic6301]

Where did you put the positive wire the red wire input

[@ErCanEverything]

The red cable is connected inside to a common point on the motor. Such a simple circuit works only with 4 cable motors where the positive cable is connected to a common point

[@markanthonycaintic6301]

@@ErCanEverything thanks i was just making sure i was thinking about that one. Thank you

[@the-beneficiary1809]

he cnnect to the wye cnnection in the motor but how would you connect a common if it was wired delta?

[@juancinta19]

Can this run on BLDC 36v?

[@manjithalankesha1562]

What is the power? 12v? 48v?

[@ErCanEverything]

18V max

[@brucecalder7752]

@@ErCanEverything Thank you. Nice job and very instructive. I was able to make your ESC and it is working for an brushless motor from a CD player. Wondering why you say 18V max when the FETs are rated at 55vDC drain-source?

[@ErCanEverything]

yes however in this circuit zener diodes must be added between S and G

[@donnieelverjuandediosmende824]

Cool! Felicitaciones! Con 6 Mofet para 36v?

[@ErCanEverything]

Hi friend I found this controller at a very good price of $11 which does a very good job. and I bought 4 pcs. I am very satisfied with them. I wanted to let you know if you need a 36V controller🙂 a.aliexpress.com/_EQ6fwQL

[@S_e_r_g_ei]

I'm watching from Russia. Well and qualitatively done! Simple and clear! Respect to the author! But, I'm not very good at electronics. Therefore, the author, please tell me where the INPUT and OUTPUT to the motor are in the scheme?? . Смотрю из России. Хорошо и качественно сделано! Просто и понятно! Респект автору! Но, я не очень силён в электронике. Поэтому, автор подскажи пожалуйста, где в схеме ВХОД и ВЫХОД на мотор??

[@nassimkoubeissi5814]

hello is this a multipoint unipolar motor or it's a bldc motor star connected with common neutral point ? and how is the driving switching sequence produced?

[@ErCanEverything]

Hello this BLDC motor was Delta, but i turned it into a Star with a common point. And driving switching sequence becomes the help of the connected resistors and diodes. When one transistor closes the circuit gives a signal to the next transistor and begins the endless process of rotation.

[@jeanebarbosa2744]

Amigo este fio vermelho está saindo de onde ???

[@ErCanEverything]

The red wire is connected to a common point on the star type motor

[@jeanebarbosa2744]

@@ErCanEverything vc sabe fazer usando um pwm ci555??

[@mahendrasinghthakur188]

40 amp and waht volt motor cab be run? Can we run 48v motor with this?

[@rayan276]

hello friend in the case that I have a three-pin disk, how would it be, which one would not connect?

[@danishhaikal8343]

It can face how much voltage?

[@isaacmalco452]

Can I use a 10k pot?

[@ErCanEverything]

Yes

[@tcw8431]

Is it reliable to driver a 12v 1200kv rldc motor?

[@DocBen19]

Congratulations for our video, how can I make more power for this project. Like several mosfet in parallel. Please let me know.

[@ابتكاراتوتحديثاتفنيه]

اتجاه الدوران لايحدد بهذه الطريقه ممكن يذهب يسار او يمين لان السنسر ملغات ثم لم تقول مصدر التجهيز كم فولت 6 فولت او 12

[@terjeoseberg990]

The voltage probably depends on the motor, and the direction is determined by the resistors and diodes. The motor should only run in one direction. To reverse the direction 3 diodes need to be swapped with 3 resistors and installed in the proper orientation.

[@priyanthavijitha4530]

Very good give me cicuit diagram and past list please

[@ErCanEverything]

Everything is written in the description and the circuit diagram is at 2:10

[@joxebamendizabal8086]

Muy buenos tu video gracias por compartir tus conocimientos , podrías ayearme con un controlador de velocidad para un motor paso a paso gracias ..

[@bitsurfer0101]

You should use an H-Bridge for stepper motors

[@FM_soomro]

This BLDC Motor is Star Connection, if IDelta Motor, then how can I use this your designed Controller?

[@ramanarao32]

There is no protection if Mosfet shorts...but simple to implement. are you using back emf as gate drive?

[@ErCanEverything]

No protection and works without EMF signal, mosfets trigger the next one with a signal from one another.

[@Ironboyhight]

​@@ErCanEverythingDo you have any idea how change delta into star 4 face please answer

[@freeenergy8273]

Vienkārši un labi! 👍 Varbūt pamēģiniet pielikt kapacitāti 47μf uz ( D1,2,3 katodiem pret kopējo mīnusu) lai samazinātu palaišanas strāvu ieslēgšanas laikā?

[@ErCanEverything]

Thank you very much! This is a good idea, I will try it. When starting with a battery 2 times burned out transistors, then I tried with controlled current from the laboratory power supply.

[@pragatmudra8372]

Could you show it in the form of schematics plz

[@ErCanEverything]

There is a diagram at 2:10 but i forgot to add the BL motor

[@freeenergy8273]

@@ErCanEverything Sveiki! LAIMĪGU JAUNO GADU! 🎄🎄 Kā veicās ar kondensatoru , labāk ir?

[@pragatmudra8372]

@@ErCanEverything what kind of cap polarised non-polarised???

[@willtech1759]

Sir, How many watts that one? Can I use that for 310vdc 120w?

[@MichaelVx]

i see its a 4 pins not 3 pins one how can it be used for the 3 pins ones then

[@ErCanEverything]

For 3-pin control it must be with 6 MosFet's and controlled by a microcontroller. I converted my BLDC motor from Delta to Star type connection

[@MichaelVx]

@@ErCanEverything i see was having hope for an easy for the 3 pins motors to be under control like the 4 pins ones

[@dejesusmontiel526]

Tengo un motor de ventilador de aire acondicionado invertir, dice que consume 35 wats y el voltaje en la etiqueta es de 310 voltios. Este control podría servir para hacerlo funcionar? Alguna sugerencia?

[@Shahnawaz_0_]

Bro is it works for Delta connection

[@bbsunsen]

IRFZ44N kullansam değiştirmem gereken devre elemanı var mı?

[@ErCanEverything]

Sorun olmaz aksine daha dayanıklidır IRFZ44N,. Aslında ben IRFZ44N sipariş vermiştim ancak videoyu çekmeye başladığımda farkettim ki IRFZ34N göndermişler.🙂

[@yumurtalıkokrec]

@@ErCanEverything bu devre nasıl çalışıyor baya Bi araştırdım ama bulamadım

[@ErCanEverything]

@@yumurtalıkokrec Devreyi kapattıgımız andan itibaren Mosfetler biribirilerini tetikleyerek sonsuz döngü başlıyor ancak ESC ve Diğer BLDC'ler kadar verimli değil

[@yumurtalıkokrec]

@ErCan Everything sürekli belirli milisaniyeler ile flaşör gibi her sargı teker teker sıra şeklinde kapanıp açılıyormu yoksa başka Bi düzenekmi var

[@yumurtalıkokrec]

Mosfet lerin çok detaylı şekilde bilmiyorum aklımda yapılabilecek tek bir fırçasız motor var hall sensörü statordaki N kutbu rotor daki N kutubuna geldiğinde devreyi açıp kapayıp döngüye girmesi