A quick clip showing how to get your wing piping on speaker baffles dead straight for a professional finish.
Пікірлер: 24
@PJ-ee5mc3 жыл бұрын
Thank you so much! This was very helpful. I loved the idea of warming the piping in hot water and then hanging it with a little weight to straighten it out. I am building several high-end cabinets (in the style of Friedman) that will have gold piping. I want them to be perfect so your tips will be a huge help.
@ModulusAmps3 жыл бұрын
That's great. Good luck!
@stuartharvey3691 Жыл бұрын
that amp looks absolutely beautiful
@EnmandsBand12 жыл бұрын
thanks, that's a great idea. I have done tolex on a couple of cabinets and now I'm building two amp headshells and they need some (straight) piping...
@Les5374 жыл бұрын
Just what I needed. Thanks, boys.
@zurdoremi3 жыл бұрын
I would like to see how you do the speaker baffle cloth, piping, and gold edging on a Vox Buckingham, or Viscount, or Royal Guardsman cabinet. Thanks.
@TempoDrift14805 жыл бұрын
Damn that fucker looks slick. I'm fixing to make set of four, two stacked side by side. I think I want to make my panels flush to the front like you got going on but I guess I'll have to mock a few up and see what looks best.
@UndeadBoogie2 жыл бұрын
Brilliant!
@mrh25955 жыл бұрын
Top tip ✌️
@francisvilla10 Жыл бұрын
Great video, when you are building a hiwatt head cab, do you this trick to be able to do the angle part? This is my first time building one
@ModulusAmps Жыл бұрын
Which angled part exactly? Yes we do this on most cabs when needed.
@utahprepper89252 жыл бұрын
I know this video is over three years old so commenting may not be seen. Regardless, is there a video showing how you got the tolex so perfect around the round opening?
@ModulusAmps2 жыл бұрын
There is, i need to do a better quality one but this should help. kzbin.info/www/bejne/rJi1anqalsierqs
@kastor82744 жыл бұрын
Awesome trick ! How much clearance would you use for salt and pepper cloth ?
@ModulusAmps4 жыл бұрын
3.2 - 4mmmm all around is a very tight fit
@kastor82744 жыл бұрын
@@ModulusAmps Just to make sure I get that right. Do you mean 3.2-4 ,, on each side or for each axis ?
@ModulusAmps4 жыл бұрын
@@kastor8274 each side. Look at the thickness of the tolex, cloth and piping. I use 3.2mm Fr4 board to check gap spacing. For thicker grill cloths and tolex you may need more space. So 4mm all around is a good bet with this stuff
@kastor82744 жыл бұрын
@@ModulusAmps Thanks so much ! Well I won't use any tolex, cos its too expensive, I'll go with that structural paint. But since I will use salt and pepper I'll go for 3.8 mm .
@garymorrison41394 жыл бұрын
I want to install piping trim on a Marshall 4x12 cabinet. Does anyone have experience doing this, please advise?
@ModulusAmps4 жыл бұрын
It's installed inside the cabinet. Not attached to the baffle
@garymorrison41394 жыл бұрын
Is the baffle held in place with removable screws, visible from inside the cabinet? I have not removed the back on one of these yet. I assume the piping would be attached to the edge of the enclosure with staples?
@ModulusAmps4 жыл бұрын
@@garymorrison4139 yes you have to take the back off to get the baffle out first