DIY Carb Sync Gauge Set Calibration

DIY Carb Sync Gauge Set Calibration. In this video I show you how to calibrate a gauge set for synchronizing motorcycle carburetors.
If you found this video helpful Please Like & Subscribe, Share & post comments. If this video saved you money please send me a tip with super thanks, it will help me get paid for making these videos. Thanks for watching! Until next time!!
Some of the links below are affiliate links. If you purchase through these links, it won’t cost you any additional cash, but it will help to support my channel and might save you money on some products. Thanks!
Product Links:
ABN Carburetor Synchronizer: amzn.to/3jHOMh4
5/32 high temperature vacuum line: amzn.to/34QvOk2
Vacuum Connector Assortment: amzn.to/358o4dt
Zip Ties: amzn.to/350hBRM
Safety Wire: amzn.to/2EWrwww
Safety Wire Twist Pliers: amzn.to/3bjtBPn
Vise Grip C Clamp Pliers: amzn.to/3gMq2lO
Music:
Song
Beach - MBB
/ mbbofficial
Song: LiQWYD - Call Me
Music provided by Vlog No Copyright Music.
Creative Commons - Attribution 3.0 Unported
Video Link: • LiQWYD - Call Me (Vlog...
Song: MusicbyAden - Dusk (Vlog No Copyright Music)
Music provided by Vlog No Copyright Music.
Video Link: • MusicbyAden - Dusk (Vl...
Song
Feel Good - MBB
/ mbbofficial
Disclaimer:
Willow’s World of DIY assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Willow’s World of DIY recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, expensive electronics, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of Willow’s World of DIY, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not Willow’s World of DIY. Only attempt your own repairs if you can accept personal responsibility for the results, whether they are good or bad.
#CarbSync #Calibration

[@ExtraSussySauce]

This was an awesome tip for these cheap testers, until you popped the cover that way I couldn't understand how to get the darn thing apart. Thanks

[@absolemjackdaw6677]

Hi, I generally don't comment on videos, but I just wanted to say Ive got the same vacuum gauge and I was about to give up on it, but your tutorial gave me back some hope ! Will definitely calibrate them now. Question, do your knobs to turn the vacuum on or off have a lot of play too ? mine have some play on it ...

[@WillowsWorldofDIY]

Yes the vacuum adjustment knobs on mine have some play as well. I'm glad to hear that my video gave you some hope. When this gauge set is calibrated it works good for syncing the carburetors. I hope this is helpful. Thanks for watching!

[@nathanaelfrye829]

Do I have to do this to be able to sync my carburetors

[@wobblesandcars]

I have this same gauge set. Thank you for your video. Iam syncing carbs on a 84 Honda 700 (magna) The adapter pieces on my carbs thread into carbs. So the narrow part connects to the gauge hose. Got any good tip on how to keep that narrow part and hose, tight? The ring clips don't work well in that application, same with zip ties :(

[@WillowsWorldofDIY]

I press hoses on firmly and they usually stay on the narrow part of the connectors, but if that doesn't work I use safety wire wrapped around the hose and twisted tight or use small hose clamps. I hope this is helpful. Thanks for watching!

[@grabovica75]

Hi Willow, could you pls show me where to find flusher reley on Yamaha R6 rj03 and how to change him. Thanks

[@WillowsWorldofDIY]

The flasher relay is located under the driver's seat on the right hand side near the right hand seat mounting bolt. the relay has an electrical connection and you will need to unplug it and plug in the new relay. It's really easy to replace the flasher relay and it only takes about 5 minutes. If you need more help please email me and I can send you an electrical schematic showing you exactly where it's located. My email address is in the about section on my Channel home page. I hope this is helpful. Thanks for watching!

[@fsociety4829]

Hi willow , what is the diameter for this specific hose you used for the calibration ? and the t adapter , can you provide some links?

[@grabovica75]

Hi Willow, could you please show me where to find flush relay on Yamaha r6 rj03 and how to change him

[@WillowsWorldofDIY]

The flasher relay is located under the driver's seat on the right hand side near the right hand seat mounting bolt. the relay has an electrical connection and you will need to unplug it and plug in the new relay. It's really easy to replace the flasher relay and it only takes about 5 minutes. If you need more help please email me and I can send you an electrical schematic showing you exactly where it's located. My email address is in the about section on my Channel home page. I hope this is helpful. Thanks for watching!

[@grabovica75]

Thanks, if you just send me a picture I'll be thankful for that. Greetings