DIY Carbon Fiber Steering Wheel, Professional Production how it's made (PART 2)

-Self made Carbon steering wheel in Carbon restoration part 2
If you have ideas what we can do next, write it please in the comments👍🏼
and don't forget give a 👍🏼.
Thanks.
videos of production coming soon, so give a abo and like to see more in near future, thanks 👍🏼
▬Recommended Equipment ▬▬▬▬▬▬▬▬▬▬▬▬▬
🪚Mirka DEROS 650CV Exzenter: amzn.to/3SPV4x8
🪚Mirka Abranet P80 Ø 150 mm :
amzn.to/3SPV4x8
(Bei den Links handelt es sich um bezahlte Affiliate-Links. Dir entstehen dadurch keine Zusatzkosten.)
▬ More Videos ▬▬▬▬▬▬▬▬▬▬▬▬
Carbon Fiber other Projekt, Carbon fiber
steering wheel how its make in this video : m.youtube.com/.... m.youtube.com/....
#carbon
#carbonfiber
#carbon_fiber
#carbonnation
#carbonparts
#carbonsteeringwheel #restoration
• DIY Carbon fiber car p...

[@UYC.]

looks brand new great job 👌

[@garydeandeery]

At the ends I used black gasket seal it turns like rubber when dry Tape each side leave a 10mm gap then lay out the seal and flatten off pull the tape off when wet still at an angle so you don’t get a lip. Works perfect

[@CARBONART.]

I don’t know exactly what you mean?

[@rawrtravisrawr]

what grit sandpapers are being used in this? and in part one are you doing each round of epoxy 1 hour inbetween or 12hours between?

[@CARBONART.]

Hello, 80-100 / 240 / 600 45-60 min between each round

[@rawrtravisrawr]

@@CARBONART. great thank you ^_^ will there be part 3 for doing the leather on sides?

[@CARBONART.]

@@rawrtravisrawr hello, maybe in the future our leather partner will be make a video for us, the leather wie didn’t made.better give it to Professional worker if you want have a perfect result

[@rawrtravisrawr]

@@CARBONART. for the grits is it like then this? or when do you do 240 / 600 sand with 80-100 grit apply carbon fiber layer apply 4 layer of epoxy full cure sand with 240 grit to level sand with 600 to smooth clear coat

[@CARBONART.]

@@rawrtravisrawr hi, After clearcoat, 3-4 layer you must tempered the parts around 8 hours by 70-80 Celsius to make the Resin heat resistant, after this we start with 80or 100 grit. At next we use 240 and finish with 600 under water. You can use 800 too but not finer, If you use 1000 or more the clearcoat will not fix so good. If you have pinholes after clearcoat, you can sanding it again with 600 and repeat the clearcoat. It’s important to have no air bubbles in the resin for a perfect for the clearcoat.

[@nourdinikanour1759]

why do you paint it black?

[@CARBONART.]

It looks better/cleaner after spray clearcoat

[@shotgun4167]

Part 3 please??

[@CARBONART.]

Hi, what do you want see in part 3?

[@shotgun4167]

@@CARBONART. how u insert the litle leather there up in the midel

[@nourdinikanour1759]

9:31 why do you paint it black?

[@CARBONART.]

It looks better/cleaner after spray clearcoat

[@ignasrucinskas4401]

Amazing work, may I ask what was the purpose of the black spray paint? Would really appreciate a response, I am doing a carbon project on my own steering wheel

[@CARBONART.]

we use black paint before clear coat for a cleaner result for the finish product. On the steering wheel maybe not so important, but if you make a Dekor panel or other parts, looks better when the back is clean and matte black

[@nourdinikanour1759]

why do you paint it black?

[@CARBONART.]

For cleaner result

[@dgonilesnoi3436]

Здравствуйте, вы прям на резиновую основу руля,накладываете материал?

[@CARBONART.]

Yes 👍🏻

[@nourdinikanour1759]

9:31 why do you paint it black?

[@CARBONART.]

It looks better/cleaner after spray clearcoat

[@nourdinikanour1759]

9:31 why do you paint it black?

[@CARBONART.]

It looks better/cleaner after spray clearcoat

[@markkraus3598]

That’s slick looking ! How many hours to do that , 25 ? When you did the final clear did you use a automotive clear or Dura Tec w/UV inhibitor ? And yes,A 3rd showing the final assembly would be good to see . Oh yeah,what do you charge to do that ? Thanks & have a good one ! One more thing-where did you find the orange battery small sander ?? Thanks

[@CARBONART.]

Hi, 3 part with the leather is not possible. The Alcantara make a other company for us. The orange machine is not the best. We use a other today. You can look in eBay for a mini polish Maschine. 25 hours? No.. the real active time to produce a Carbon steering wheel from start to finish take 3-5 hours. But over days. We need time for dry the layers. The leather job from other company I think 3-4 hours

[@markkraus3598]

Thanks for the response! I do a lot of composite work in custom cars so other types of work get my attention. For recovering I’ve used “Craft Customs” in Texas & they do very nice work ! I found a sander on Amazon- SPTA battery polisher kit for $190. Have a good one 😎