DIY CNC Mill ( DIY CNC Freze )

[@HISSTECHCNC]

Sizde böyle bir tezgaha sahip olmak istiyorsanız irtibat numaramız [phone] Aklınıza takılan sorularınızı iletebilirsiniz.

[@HISSTECHCNC]

@Abdullah Emre BaşkaleAleykümselam Bursa da yaşıyorum.

[@behlulsimsek8708]

@@HISSTECHCNC ürünü yeni yapmışsınız, eskiden maliyeti baya düşüktü malûm kur. Ne kadar maal oldu acaba?

[@semihtohumcu5743]

Güzel tasarım elinize sağlık. Elektronik parçalar ile ilgili bilgi verebilir misiniz? Step motorlar, trafolar, kontrol kartı gibi. Nereden temin ettiğiniz ve özellikleri nelerdir?

[@HISSTECHCNC]

@@semihtohumcu5743 Öncelikle teşekkür ederim yorumunuz için. Kullanılan step motorlar Nema 34, diğer mekanik ve elektronik parçalar videoda detaylı olarak görünüyor. Parçalar birçok firmadan temin edildi. Ürün kalem sayısı çok fazla olduğu için buraya yazmakla bitmez.

[@HISSTECHCNC]

@@semihtohumcu5743 Abone olmayı unutmayın lütfen.

[@auroraRealms]

This is an amazing build. There is one problem it seems that people keep making (probably to save money) on the y axis. By putting the slides on the mount and the rollers on the table, the force changes on the y axis as the part moves in the y direction. If the Rollers where mounted on the mount and the slide table contained the rails, the milling force would always be centered between the 4 y rollers. The same could be said for the x rollers and slides as well.

[@TinkeringNerd]

I don’t see how that saves on anything, really. The way they did it uses more linear rails than if they flipped the x-axis.

[@auroraRealms]

@@TinkeringNerd It is less about saving, and more about keeping the center of force centered over 4 points. If the part is really long, the edges are unsupported, because the bearings will be off to one side. Even a small part changes the force applied, as the bearing move to one side or the other. If the x-axis bearings are always fixed at 4 points equally spaced below the cutting head, I would think the the cutting accuracy, and the force that can be applied, would be increased.

[@pnuema1.618]

@@auroraRealms Wow this is brilliant! I will keep this in mind when designing my mill!

[@liquerinfrnt]

@@auroraRealms pretty much all cnc mills use the rails carriages attached to the table design. You wouldn't machine anything that hangs over the table on this type of machine. It is more stable over the table at the cost of limiting travel, as opposed to a bridgeport style manual mill where the entire table can move across the entire range of motion, but gets cantilevered out at the edge of travel

[@augustinvangeebergen8213]

The bearings are supposed to have a preload and withstand up and down forces... plus, I think you're speaking about the x axis

[@tech477]

OK, I admit, I watched it three times, and saved it for the future.

[@HISSTECHCNC]

Thank you

[@buckylaine]

Beautiful machine. I wouldn't try to guess how much time you actually have in building it. Thank you for sharing.

[@liboy34]

Hi Great job realy 👍👍 What's kind of Steel is used for this project ?

[@kenantamyuksel8110]

Her şey süper magazin yapımı bekliyorum.

[@TrPrecisionMachining]

very good milling machine..thanks for your time

[@HISSTECHCNC]

Your wellcome.

[@tunahanaydogan6068]

neden Z eksen motoru yataklamaya o kadar uzak anlamadım cok sağlıklı durmuyor

[@asgharrezaei0138]

My dear you have done a good job so far ,but you will be losing steppes in future because the Z axes does not have balancer , it needs the vertical wight of Z to be balanced , You can use difrencial wight by chain in back or use penumatiuqe system , good luck (this is only my sugestion )

[@HISSTECHCNC]

Stepper motor is closed loop. Thank u for advice.

[@jonjon3829]

nice platework man.

[@jazzyyyjazz1112]

Excellent job, I want to make my own cnc, can tell where did you find, all the controllers

[@janvanik8945]

Nice work. But mass is good for base. Holes in base is not necessary.

[@Bg_Anipar]

Solidwork?

[@TannerFrisby]

Very clean build. Nicely done.

[@spm2508]

hi Machine looks good...! what is the Machine Spec....? and are you selling this machine ?. if yes what will be the cost ...?

[@MrIRONbox]

Após a solda se faz necessário esperar no mínimo 6 meses antes de realizar qualquer processo de usinagem. Na verdade isto é obrigatório devido ao empenamento causado por as tensões internas do aço.

[@banzaiwill7672]

Nice! Did ypu stress relieve after welding? If not, did you have any issues with straigjtness after machining?

[@HISSTECHCNC]

Yes I did.

[@banzaiwill7672]

Awesome. Machine is amazing. Well done.

[@behlulsimsek8708]

Dairesel interpolasyon yaparken yarı çapta duraksama yapıyor bunun sebebi nedir? Sürücüler ve step motorları olabilir mi? Postu kontrol edin i ve j kodu ile işleme yapıyor ise ondan da olabilir birde x y r postu ile deneyin belki duraksama yapmaz.

[@HISSTECHCNC]

Mach3 içinde bulunan paket ile işleme yapmıştım. Paket ile alakalı bir duraksama.

[@brianalbers2260]

Are you sharing the design files/cad files?

[@seimela]

This looks awesome

[@m3chanist]

You did heat trat and stress relieve it after welding before machining huh ? Only you didn't show that and if you didn't..well good luck ever produceing accurate parts with the twisted pretzel it will soon become.

[@HISSTECHCNC]

Yes i did it before machining.

[@m3chanist]

@@HISSTECHCNC Thank goodness ;)

[@car9167]

@@m3chanist How would you do that? Put the parts in some big oven and keep at what temperature and for how long?

[@mihailfelixdumitresc]

@@car9167 Trebuie facuta o recoacere de cristalizare. Nu o poti face acasa. Trebuie facut la o firma care face asa ceva. Palierele de coborare si mentinere a temperaturii se gandesc in functie de marca de otel si de grosime. Nu-ti poate spune nimeni pe dinafara pana nu stie detaliile acestea. Sa ajunga cuptorul la 680 de grade nu e greu, sa racesti piesa intr-un anumit fel este mai dificil.

[@car9167]

@@mihailfelixdumitresc Indeed I have no way to do this at home. I was thinking to "work" the welds while they are still hot, that will remove some of the stress. Also heat it with a torch section by section. In the end for what I'm trying to do I think some of the stresses will be blocked. My design is made of steel square tubes 4" X 4" welded together in a frame with the shape of an H. The tubes will be filled it with epoxy concrete. I think that would block some of the later movement... will see

[@gvpf2a]

......была бы кнопка супер я бы её использовал..... лайк.

[@度空-u5r]

铸铁的他不香吗！这玩意儿容易变形

[@barbeirorp]

Nice machine. This spindle is a. er or bt

[@HISSTECHCNC]

Thanks. Spindle is a ER.

[@rofiscreation2316]

what is the thickness of this plate?

[@raixr2197]

Nice work. Can You make small summary about work price: 1) Lasercutting 2) Milling cost (Base, Z-column)

[@HISSTECHCNC]

Thanks. Total price ( machining, laser, welding...) about 1500 dolars.

[@HISSTECHCNC]

Please don't forget subscribe.

[@premjitsingh36]

Hello sir need specs and technical drawing and cost of build

[@ishakozdemir6954]

Great machine...

[@ralfh82]

Wich nema did you chouse ?

[@hadcoM1]

great work

[@Sarthak32155]

How is the accuracy of this machine??

[@HISSTECHCNC]

Axis straightness is 0.01-0.005mm.

[@dynamicoffroadequipment4506]

Sac kalınlıkları ve toplam ağırlık nedir

[@HISSTECHCNC]

Çeşitli kalınlıklarda plakalar kullanıldı. Toplam ağırlık yaklaşık 500kg

[@sdemirel75]

Merhaba. Kaynaklar sonrası ısıl işlem uyguladınızmı?

[@HISSTECHCNC]

Merhabalar, evet ısıl işlem uygulandı. Eğer gerilimi kaynak sonrası alınmazsa bir kaç içinde tezgahın ölçüleri değişebilir.

[@Hakanınnce]

Merhaba çok güzel bir çalışma olmuş. Bir sorum olucaktı saç plakalar st 37 mi yoksa farklı bişeymi kullandınız?

[@HISSTECHCNC]

Teşekkürler güzel yorumlarınız için. Malzeme olarak st52 kullanıldı.

[@car9167]

Is it not ringing when you machine steel or something? I would have filled the base and the column with polymer concrete

[@HISSTECHCNC]

Slight shaking occurs when machining over 0.5mm with a 32mm diameter tool.

[@mihailfelixdumitresc]

Hey, nice work ! Flatness test ?

[@HISSTECHCNC]

Thanks. I'll make a video for this. Average flatness 0.01-0.02mm. please don't forget to subscribe.

[@Miniatures-And-More]

Great Job !

[@ekosiswono467]

Good job sir

[@HISSTECHCNC]

Thank you

[@Remo2239]

Great work :) Would you share the cad model with us??

[@HISSTECHCNC]

Thank you brother, but i can't share. This is my work. Not only hobby.

[@aion2177]

Is it a good idea to use welded plates? Then why is everybody trying to use epoxy granite?

[@HISSTECHCNC]

Ofcourse epoxy better then plate but long product time and need more experiense for rigidty. Not good idea epoxy for first project.

[@HISSTECHCNC]

Dont forget subscribe.

[@hzlvedikkatli6563]

ne kadar fiyatı usta

[@vijayrajan8628]

Can you share the Base and column Dimension . XYZ travel.

[@HISSTECHCNC]

Base 950mm, column 920mm. Travel X 420mm Y 250mm Z 250mm

[@ahmetcihatboz]

Ellerinize sağlık güzel işçilik, makineniz ile alakasız fakat BT30 veya BT40 spindle temin edebileceğimiz bir satıcı biliyor musunuz?

[@HISSTECHCNC]

Yorumunuz için teşekkür ederim. Belki bu linkteki ürün işinizi görür. www.arelspindle.com/ares-takim-degistirmeli-motorlar-urunu-348?category=urunler

[@galaxy5am987]

Hi, do you have parts list and cad file? thanks

[@CNCFONTAINE]

Perfect bravo !!!!

[@wesco123]

Magnificent 🏅👌

[@er.hamed2001]

Good job 💪

[@serhatkrmz4988]

Gövde de kaç mm sac plaka kullandınız acaba

[@HISSTECHCNC]

Değişik kalınlıklarda plaka kullanıldı. 10 ile 25mm arası

[@rutvikpanchal2043]

Please can you Shera part files ?

[@tomjdesigns1280]

reduce welding current when your stick start glowing or use thicker rod:)

[@HISSTECHCNC]

Thanks for advice.

[@HISSTECHCNC]

please don't forget to subscribe

[@Jeanbond2990]

Beau travail...

[@barbeirorp]

Whats This spindle?

[@HISSTECHCNC]

Arel Spindle. Made in Turkey. www.arelspindle.com/

[@nizaralhamid4563]

Ustasin abi

[@HISSTECHCNC]

Eyvallah.

[@HISSTECHCNC]

Abone olmayı unutmayın lütfen

[@ekosiswono467]

Do you have the design?

[@HISSTECHCNC]

Yes of course i did it.

[@madeinpakistan4636]

Which size x y z

[@Duet3D]

Такую серьезную машину делаете и из стали. Неужели нету литейного завода, по хорошему с чугуна надо лить.

[@Duet3D]

Сварная конструкция из стали не даст хорошей жесткости как чугун. Сварную конструкцию будет вести со временем.

[@CeNuVezi]

Friend , nice work , but i dont get it , u do a good rigid machine , and cut aluminum 1 mm doc , and a bad toolpath , with stops on a circle , and u use mach 3 wich is oudated , and doesnt foloow soo good the trejectory path at high feed . I would change the mach 3 to something more new , like uccnc or linux cnc , more better than mach 3 .

[@HISSTECHCNC]

Yes, u are right my friend.

[@felixantoniogonzalezalzate4469]

Hola cuánto cuesta la maquina

[@HISSTECHCNC]

13.000 dolars

[@ardaplbyk]

👏🏻👏🏻

[@HISSTECHCNC]

Abone olmayı unutmayın lütfen.

[@7891ph]

This thing is so underbuilt for it's size it's scary. It's going to ring like a bell for anything more than a light finish cut, and even that's going to be problematic... And the cuts the machine is making in this video are all extremely light finish cuts.....

[@HISSTECHCNC]

Pls watch my other videos.

[@ray-charc3131]

For me, i am a poor welder!

[@mcping]

Turn on G64 :)

[@made-by-p]

v

[@asutar7]

Very nice built . Can share your mail id

[@HISSTECHCNC]

Thanks. [e-mail]