Idea in this video, is to show how to make an adapter that allows one to use angle grinder backings with diy disc sander. This makes possible to change backing harder, smaller or softer if needed. Sander runs at 2800-3000rpm speed. There's a typing mistake on the video, 5000 supposed to be 3000.
@1977np Жыл бұрын
And that's exactly what you didn't show properly maybe due to lower light levels. Another thing I'm thinking is whether 3000rpm is high enough for sanding. Doesn't the motor slow down when workpiece applied with some pressure. Making adapter is useful knowledge since I also have a 2850rpm water pump motor. Thx anyway.
@abderbhm60863 жыл бұрын
Nice job, thanks for sharing my freind 🙏🏽
@Enigma-Sapiens3 жыл бұрын
Great video, ideas, and build, thank you!
3 жыл бұрын
Thank you for watching!
@artbyjiggy373 жыл бұрын
To think I threw an old pool pump away! Never thought of this! What a great idea!!!
@yeagerxp3 жыл бұрын
Excellent work 👍👍👍 . Thanks for sharing
@Everythings_Adjustable3 жыл бұрын
What a useful project, nice work! 🛠️👍😊
@henrisivonen74043 жыл бұрын
Tämä oli loistava oivallus! Paljon on pihavajoissa pumppuja joista on pesät halkaistu jäädyttämällä. 👍👍👍
3 жыл бұрын
Näin on. Voihan niistä käyttää moottorin toki muihinkin tarkoituksiin. Mutta tuota omaani kun katselin, niin lähtökohta vain selkeästi jo näytti hiomakoneelta.
@cobberpete13 жыл бұрын
Repeat some comments from below. Great tip to centre the shaft on the drill press. I wish I had seen your video a few days ago as I had a very similar problem to drill through a round bar. Also like the paper trick to change the sanding disc. Always interesting, watching your work Toumas
3 жыл бұрын
Thanks buddy. I try to add something possible useful for most, or one, to my videos. 🙂
@DanielH3 жыл бұрын
I need to make one since I have 2 motors just standing in my shop
@4acrefield8753 жыл бұрын
Good recycling , I have similar motor and fitted it with m14 stub to hold sander disk or wire brush from grinder pump motors very are very handy also used one for simple belt grinder Keep up the good work
@NjalLaing3 жыл бұрын
Nice idea indeed, I just bough one of those Bosch bench drills. It sounds terrible on the video!! Is it just the sound recording? I am worried now they are not a good machine now hearing that terrible noise!!
3 жыл бұрын
I think my microphone is set too sensitive, and speeding up video makes it sound much worse. It makes noise, but its not so bad at all.
@SMee673 жыл бұрын
That's a bloody ripper, mate.👍🏽 What an excellent score, and it will definitely earn it's keep in your workshop.👌🏽
3 жыл бұрын
Thanks buddy. I think it will be mostly used for tidying parts after cutting. I can place it next to me when making cuts with angle grinder, and then clean edges without need to change wheel to grinder.
@SMee673 жыл бұрын
@ Best thing with this one is that it is small and easy to store out of the way when you're done. 👍🏽
@PasiSavolainen3 жыл бұрын
Quite lucky machine tapping. Or do you just know that the hold on it is light enough that it won't break? Nice "trick" with sandpaper change too
3 жыл бұрын
Yep. I keep it little loose and usually spin it just to get it to go straight. In this case, i made a 20mm deep hole, and only 7mm needed to be threaded, so risk of breaking a tap was minimal.
@jarihakli43433 жыл бұрын
No onhan idea taas! Täytyy sanoa, että yksinkertainen on kaunista. Minä hölmö olen aina pistänyt pumput romuun, enkä ole ymmärtänyt hyödyntää niitä. Nyt ei uskalla enää hävittää mitään kun sinulta tulee näitä ideoita😁
3 жыл бұрын
Pistät seuraavan säästöön. 🙂
@christiantewes91433 жыл бұрын
Really like your style.repurposing is a good thing. Will you be building a belt grinder,too?
3 жыл бұрын
Yes. I have intention to build a belt sander someday in near future.
@thebrokenbone3 жыл бұрын
moi tuomas! you know i always pick something from your videos and lately i´m working late and later and it seems everything makes more noise, or i´m just getting old (both :)) the induction motor makes almost no noise compared to a universal one, i did not knew pumps were so high rpm i´ll try to find one and make a grinder for my tungstens (yup i´m dipping now... told you was getting old). paper trick is a w e s o m e too. thanks for sharing. peter ps: is moi moi for good bye or i just heard wrong from the tv?
3 жыл бұрын
Thanks Peter. Yep its actually funny that Finns use same words to say hello and goodbye. Similar word with "moi" is "terve", it can be used to say hello or goodbye too. Personally i use words " Moro ", " Moikka " or " Heippa"
@JONNIE_ROCKER3 жыл бұрын
👍👍 time to steal the pump from My summer house
3 жыл бұрын
😬
@jothain3 жыл бұрын
Tää on kyllä ihan jees. Harmi kun ei ole missään lojumassa vastaavaa vanhaa pumppua. Pitää kuitenkin pitää silmät auki
@pjhalchemy3 жыл бұрын
Cool trick with the tap in the DP! @¿@ Tapping a grade 8 SHCS is no easy feet...been there done that Kinda, with many "Binks" ;-P Think the spiral taps make a big difference. Great repurpose of the pump and novel disc approach. Would think the sponge pad would get too hot with the metal though...but cheap enough for light work. Amazing fabrication of the table supports and flat surface! Thanks for the idea, been wanting to build a 10" stand alone! Hat Tip, ~PJ
3 жыл бұрын
Thanks buddy. That's not a sponge pad. Its "semi flexiple" with rubber body. About 3mm thick from the surface is soft, otherwise its hard. Those are intented for sanding mildly curved metal surfaces before electro polishing. Of course one can get those over heated, but i have managed to melt ones only when sanding down welds that are still hot.
3 жыл бұрын
Btw. Now i noticed. There's a sponge pad at the beginning, ( red 125mm ) but the one that's been installed is different. ( Yellow 150mm ) I just used one that's near my hand, for demonstration, and that was a sponge pad. 🙂
@Lazywatchsmith3 жыл бұрын
Upeeta työtä, kuten aina. Mulla on ollut tarkoitus tehdä tuollainen siitä mun vanhasta puusorvista.
3 жыл бұрын
Kiitos. Tässä pidän omalla kohdallani etuna, että se on mukavan kevyt. Tykkään tehdä pölyiset hommat mieluummin ulkona.
@oddis1883 жыл бұрын
Ai hitto mä diggaan kyllä kattoo näitä sun tuotoksia! Aivan jäätävän nerokasta uusiokäyttöä!
3 жыл бұрын
Kiitoksia. Tässä pyrin tekemään jutut niin että siitä voisi joku kenties saada vinkkiä johonkin toisenlaiseenkin viritykseen.
@oddis1883 жыл бұрын
@ no tuossahan olis mahdollisuuksia käyttää mihin vaan tota. Mutta on kyllä nerokas tollein
@assarhadon3 жыл бұрын
The TÜV in me sagt nein. I am worried by 1) the rest being mounted in drilled plastic 2) strong forces being done on that drilled-through nut, especially when grinding towards the edge
3 жыл бұрын
Of course you are. 😄
2 жыл бұрын
But, seriously. Axle goes 25mm inside the adapter made from M14 bolt, Axle leans against sides of the bolt from that whole distance. There is now stress against the M8 thread. Adapter is as strong as is the original axle. And with this kind of sander, using high pressure would be stupid, also unnecessary. It just ruins the sanding papers. There is many different grade of plastic. Used in boats, cars, motorcycles, tools. Angle grinder, or hand drill body is made from plastic...