Can't believe no other video mentions that metal ring. Had me wondering what the heck it was. Thank you!
@MjrNiGhTmArE2 жыл бұрын
TIPS: *Don’t start machine screw(s) or bolts with anything but your fingers. After it’s started, then use your power tool. This will keep you from cross threading your screws. *On the ground wire, crimp or solder a ring connector on it, then install. If you look closely at the video, the bare wire comes loose. It’s difficult to keep a bare wire where it will stay put, without using a ring connector. *The metal colored piece has a slot in it for the horn wire. Tape the sucker in place in the grove, so you don’t smash it causing a short or open while installing. *Install everything but only snug the wheel on. CAREFULLY Drive the vehicle somewhere where there is no traffic, in a straight line to verify the steering wheel is straight. If it’s crooked, you can loosen it and reposition the steering wheel where it straight, then torque it down. I hope this helps prevent what should be an easy install from turning into a nightmare.
@hulkgarage4544 жыл бұрын
Great video ! Its 6 years old but it still helped me out for sure. Thank you.
@dallasgannon57173 жыл бұрын
Instablaster.
@graniteblueav6 ай бұрын
Awesome, thank you! After research, found I needed the spacer/adapter. That part had no instructions
@rickdaenell91102 жыл бұрын
Great video ,thank you. Just don't forget to disconnect your battery if doing an in car install.
@TCPAYNE10 жыл бұрын
Hi,That was SUPER !!!!!!!!!!!!!!!!!!!!!!!!! Thank You Wayne J.
@skeeter528310 жыл бұрын
Im sure glad you didn't cross thread the final bolts.....
@obsessivegarage9213 жыл бұрын
What in the hell is with the comments
@josephg61194 жыл бұрын
They have so many A01 adapter kits I’m not sure which one fits my truck
@randee77726 ай бұрын
Great vid
@TomsChevelle9 жыл бұрын
Thank you! Nice simple video... Got my wheel on no problem.
@browntacks708 Жыл бұрын
Good stuff 👍
@parbhum10 жыл бұрын
I think your ground wire came off mate, are you going to undo everything and do that again???
@NoMonkeyBizz2 жыл бұрын
Do u hv the adapter quick release for a GMC c3500 sierra
@robertthornton10148 жыл бұрын
Dam that was easy a rabbit can do it. great video thank you very helpful
@ParagliderCollapse8 жыл бұрын
Good video!
@uncled20173 жыл бұрын
I just got one of your steering wheels for our 1969 Camaro. The plastic housing coming out of the steering column does not have the slot so the black plastic clip will not stay in place. How can I fix this? Thanks
@nonameisthename1382 жыл бұрын
The installation is straight forward, but my issue is the horn wire is too small to connect to the horn button. It doesn't fit
@xsliick5 жыл бұрын
Mine came with an orange piece and it didn’t come with a spacer. Is the orange piece the spacer?
@humpworm9 жыл бұрын
I didn't see you replace the "retainer clip" after the shaft nut? But over all great vid...thanks
@ShopTimeWilly3 жыл бұрын
Thats because the original retainer position is under the adapter. I been scratching my head all damn dat and no matter how far i push it down. My old retainer wont go down... Drilled a hole and slid a coder pin😂
@AimlessMoto9 жыл бұрын
You really need to learn how to use a drill.... that wheel on the collar behind the chuck... that sets your torque, set it at 1 or 2 for "test fitting", then set it at "10-12" for final assembly... having it cranked all the way up or on "drill" means you could mar the bolts, cross-thread, or pinch things unnecessarily. Let the tool do the work. Also, keep the speed on "low" or "1"... that way it wont torque in your hand.
@AimlessMoto9 жыл бұрын
Yes.
@rikkografi6 жыл бұрын
amen.
@adrianbinger83973 жыл бұрын
Where do you install safety or retaining clip? Mine got loose
@medikate82776 жыл бұрын
great video. Is this pretty much the same setup as for a 93 Chevy S10 pickup truck?
@VictorGomez-vv5hm8 жыл бұрын
I try to put a grant steering wheel On my 69 toronado. But im not sure if the adapter kit. Its correct its a sw-900 of pilot installing kit. Its exactly like on video except. De second adapter
@sstrey1748 жыл бұрын
video helped...thanks
@FlGulfer27 жыл бұрын
Put on the new wheel and now my steering wheel moves side to side and up and down. I put the column spring back in but it doesn't hold the wheel straight. What did I do wrong?
@KrisKustomPaint3 жыл бұрын
Why are steering wheel adapter kits so terrible?
@crisleon713510 жыл бұрын
Is it possible to install this steering wheel on a 2000 Chevy Blazer with airbag
@cdnbroncolife18893 жыл бұрын
What steering wheel is that ?
@davidfacio6088 жыл бұрын
That column is identical to my 91 camaro rs i want to put a removable steering wheel do i need 5 bolt or a 3 bolt adapter??
@calvinwade9854 жыл бұрын
What year steering wheel?
@briandyer89073 жыл бұрын
the bell on the bell wire Is on backwards I just installed a steering wheel from forever sharp and the bell was backwards FYI compar it to the one that came stock on your car or truck and you well see what I mean!!!!!
@gavinhudson40858 ай бұрын
I can’t find this exact adapter
@grandcreator117 жыл бұрын
no videos on how to remove the original steering wheel??
@chevyxrz8 жыл бұрын
do you need a puller to remove to pull off the shaft
@tleakin10007 жыл бұрын
Thanks....Easy as pie!!
@Corphish_11 жыл бұрын
Is that by chance to a Fiero?
@cassiusclaynyc9 жыл бұрын
You need to tell classicparts to clearly state the necessity of this A01 installation kit for chevy trucks. I sat out in my drive with a steering wheel kit that came with unnecessary hardware and NO INSTRUCTIONS. Add to that a company that is not open on weekends and I am one unhappy customer. Oh and a true professional would never attach a ground the way you did. Include a spade connector and use that.
@Wow.Thats.Alex9096 жыл бұрын
Does this adapter fit a 2001 gmc sierra 1500??
@guillermofarfan23408 жыл бұрын
do you really need the spacer to installed it?
@limeybean39678 жыл бұрын
that steering column looks identical to my 92 Riviera column... see it on "airride riviera" youtube
@brandonneil89548 жыл бұрын
its an s10 tilt column
@jperalta2589 жыл бұрын
how can i remove an after market and put a stock one back on do i need a special tool?
@kylesplace8 жыл бұрын
+juan peralta I picked up a column from the junkyard, the steering wheel was missing but it had this 3 bolt adapter. I used a normal 2 bolt puller from the auto parts store, screwed in 1 bolt then started tightening the puller then as it started leaning to the side with the 1 bolt i hit the other side with a hammer and it popped right off. Probably not the best way but it worked for me.
@QdotRich5 жыл бұрын
I ordered that exact steering wheel and received a beige one. 🤦🏾♂️
@spareglizzymaam77257 жыл бұрын
HEY! Important. Can I use a 6 bolt spacer with a 9 bolt wheel? I can't find the spacer I want in a 9 bolt! HELP!
@vaschy23302 жыл бұрын
Damn its been 4 years since u commented this. How did it go
@braleyshardwoodcustoms85844 жыл бұрын
What's the kit go for$USD pls?
@roymckinney58054 жыл бұрын
60 bucks
@tubehead8203 Жыл бұрын
My wire has a different tip
@lit549 Жыл бұрын
Dam, sure wish I didn't have to run that spacer!
@eduardoescalera11768 жыл бұрын
That steering wheel looks like a 2001 Camaro steering wheel
@calvinwade9854 жыл бұрын
I've got a 98 Chevy
@victorcastro94404 жыл бұрын
Nice video 👍 only thing the noise of the drill it's annoying
@kenkillya80832 жыл бұрын
You're really gonna just wrap copper strands under a bolt in an instructional video?
@Fhita196211 ай бұрын
Agree, ring connector would be nice.
@skeeter528310 жыл бұрын
Im sure glad you didn't cross thread the final bolts.....