DIY: How to Replace Rear Window Regulator 00-06 Chevy Avlanche / Silverado

[@larrymor]

Replaced it just as shown in the video. No problems with the regulator assembly but that black sealant should be hazardous material. Despite my best efforts that stuff got on my tools. I had to used mineral spirits to clean up. It actually took longer to put the inside door panel on and tighten the screws than the regulator/motor assembly installation. My Suburban is so old that the two top inside clips broke even though I was very careful when I remove the door panel. Thanks for the video.

[@alphonse53]

Watched as a refresher. Replaced other door a couple years ago. Would have helped a lot to be able to see behind the plastic.

[@socalaccessories6687]

I'm working on making the sound and quality of the videos better as I go.

[@quiettime6871]

Good video with some really handy tips, The plastic didnt bother me too much, I was just looking for an overview. Looks like I'll be tackling this job in the next day or two

[@evoll3303]

Thanks for the video. This worked great on my 06 Silverado. Got the part off Amazon for $46. Thanks!

[@ArmenArmenjs]

Thanks for sharing. I have same issue with my 04 Avalanche. It seems actuator motor works just the window gets stuck time to time. Silicone white spray grease would help the rails lubed.

[@gwilson61]

Thanks for the video - I just did this on my 2003 Suburban.

[@ya-man2916]

Move the plastic!!! Take key out of ignition! Good advice on the reverse up/down explanation.

[@acanfield87]

Good video and discussion on potential wiring issues. I understand why you didn't remove the plastic since you have to also remove the door handle--why take off stuff you don't need to unless really required. Sure, it's a quick removal but you can also break stuff on these old vehicles when you remove it (been there, done that).

[@rubbermallet3873]

if you dont get your reply is because your question is irrelevant dude 🤣😂😭💤

[@yasinwarsame8867]

Nice video thanks

[@charles2088]

Very easy video helped us got it in fixed thanks

[@ricktaylor3748]

Roll your window all the way up. put some strong Zip or duct tape across the top of the door frame. It holds the window up, so you won't have to fight with it falling down. Make sure you put the plastic moisture barrier back on. Go smoke some weed & relax. Then put the door panel back on. I suggest buying an AC Delco regulator, they always fit and work better than Chinese junk.

[@jeffreycornelius3091]

next time try to show procedure without plastic in the way.

[@bigbob4191]

Mine is doing the exact same thing It rolls down but then it only rolls up halfway and it feels like it's getting caught up on something sounds like it too I'm not sure what's wrong with it

[@rennie400]

I watched and you made i a snap to change. It took longer at parts store than to replace it.

[@josemoya8254]

Where do I buy the parts or what’s the link for it?

[@mrkarterhuh9830]

Thanks for the video. Some asshole Rome my rear window and even though I got a new window now it doesn’t roll up or down and falls down.

[@lwilliams1833]

My only recommendation would be a close up view of the brackets, screws, and misc things because I'm a beginner that doesn't want to pay $100 for someone else to put in my regulator. Otherwise, good video.

[@socalaccessories6687]

L Williams thanks for the tip I’m still new to KZbin and making videos I know how to install a lot of stuff and we do installs at my shop every day so I’m trying to start making some videos to help people out that are more detailed then other peoples videos

[@brandofalcon]

Great vid! Do you have a list of tools needed for this?

[@SNuts-bu7pn]

Where u located in SoCal?

[@fordwelch9477]

I just replaced mine and it seems like my window doesnt go all the way up now (like a quarter of an inch short) and also after i plugged my regulator in it still wont go up and is just locked in place i dont know what the problem is

[@angelacosta1465]

I got 2 Window's out on my 2006 Suburban 😭

[@kilroy75633]

Move the da** PLASTIC so we can see what you are doing... And talk a little lower, I almost heard what you said earlier... Otherwise great video

[@JimmyRoe-c7c]

TAKE THE DAMN PLASTIC OFF!

[@bej5534]

Bro we can't see what you are doing awful video

[@rubbermallet3873]

then pay $90 pwr hour so we could baby sit you idiot 😂🤣😭😋😁💤