DIY Hydraulic Press Brake PART 1 - Repeatable Bends using Limit Switches

[@RathaSochenda]

Want to build your own Hydraulic Press Brake? Links to the DIY Build Plans: My Website Shop: rathasochenda.com/product/diy-shop-hydraulic-press-brake-digital-build-plans/ or Etsy Shop: rathasochenda.etsy.com/listing/1575803667/diy-shop-hydraulic-press-brake-digital Video Description: How to build a homemade pressbrake. In this video series, I’ll share the process of building out my homemade brake press, which will include a NC control back gauge and limit switches to tell how far the punch die needs to travel down to achieve a desired and repeatable bend angle. Items used in this video: Cyclops Press Brake Tool: instagram.com/cyclopsdesigns/ Vevor Electric Hydrualic Pump: s.vevor.com/bfQh9Q Vevor 30 Ton Cylinder: s.vevor.com/bfQh9M Anti-Wear Hydraulic Fluid: amzn.to/3Lt3YP9 Limit Switch: amzn.to/3qZNw1Z Return Springs: amzn.to/47X0YnM Linear Rail: amzn.to/3L2KLnp Digital Angle Gage: amzn.to/3QZTESt Leveling Caster 2200lb Capacity Set of 4: amzn.to/486WB9U Video Chapters 0:00 - Introduction 0:50 - Why I need a Brake Press for my shop 3:15 - The Goals for this Brake Press System 4:00 - My Shop Brake Press Design in SolidWorks 5:47 - Building a Hydraulic Shop Press H-Frame 10:11 - About the Cyclops Design Brake Press 11:21 - Bending Parts 12:35 - Limit Switch to make repeatable bends 15:04 - Conclusions

[@PCOSAMUDERAPTwf]

Bro u use gas or oil for this hydraulic

[@kkarllwt]

This is how a video should start. An introduction, An explanation of the problem to be solved, and a demonstration of how you solved it. Before one cut or weld. I will decide if I want to watch you build it. Well done.

[@RathaSochenda]

Thank you!

[@phillhuddleston9445]

Much better than a one minute music video!

[@ElKing-yz7tz]

This is the most underrated DIY channel so far 😢. Great build buddy !! Can't wait to see part2

[@RathaSochenda]

Appreciate it!

[@mrvector257]

Damn, I just stumbled upon this channel and it's great. I love when people bridge the gap between engineering design and fabrication themselves. Keep up the great work, man.

[@RathaSochenda]

Thanks!. Yeah it definitely can be a challenge bridging that gap at times.

[@roxifbabyyy]

It’s so awesome to see your process. The thought process is top notch 👏🏽🔥

[@RathaSochenda]

I appreciate that!

[@CurtisGurley]

I have watched several of your videos. You do excellent work and show characteristics of a seasoned fabricator. You have earned a subscription from me. Thank you ( from a fellow fabricator) for excellent projects and taking the time to film and edit your already great content.

[@RathaSochenda]

appreciate it! Thanks for the kind words.

[@kendallchaffeeband]

This is the best press brake build I've seen on KZbin. Well done!!!

[@RathaSochenda]

Thank you appreciate it

[@Factory400]

Great design....great execution.....great presentation. Really helps me justify a CNC plasma table. Having the freedom to get parts fast and iterate at low cost is gold. That was initially why I got into CNC machining - it was too expensive and very slow to prototype. Having all the tools in-house provides so many design options. Love it.

[@RathaSochenda]

Appreciate the kind words! Alway helps if got can do it in house especially when prototyping

[@mwinner101]

That thing is awesome! Great design. 👍

[@RathaSochenda]

Appreciate it! Stay tune for part 2

[@isaaclaughter]

Bro, I saw your trailer video and watched twice on two separate occasions. I am very impressed with your skill level and your calm approach to actual big engineering problems. I bet you don't even think that you are that book smart, but clearly you are. Stay humble and just leave the compliments to us viewers cause you clearly deserve them. Just wanted to take a moment to congratulate your hard work and sticktoitivness. You only make it look very easy but so many of us viewing know that these things are hard to do for the average person. Lastly, I came to this vid based on a clean out of my KZbin subscriptions. KZbin (and for that matter all Social Media) is so very overwhelming. Clearing out 'junk channels' is the best decision for me. However I couldn't bring myself to delete Greg Owens, Marquez Brown Lee and a few others. You are among the few that made the cut. I actually don't think I'll ever unsubscribe from your vids. Again, great job on this entire channel and I hope your financial goals are reached due to your love of what you do.

[@RathaSochenda]

I appreciate it

[@darolfishman3470]

Your builds are awesome! So innovative and of the highest quality.

[@RathaSochenda]

Glad you like them! I try to do my best!

[@JohnSmith-ud9ex]

Project, videography and dialogue are absolutely top notch ! Fantastic to watch = )

[@RathaSochenda]

Thank you I’m glad you enjoyed the video. 😎

[@c.harris7823]

Very impressive project. Well done.

[@RathaSochenda]

Thanks

[@phillipchambers8487]

Great Video! Like I told you IG I will definitely be ordering one as soon as they are available. This is Leaps & Bounds above the HoBo Freight 20 Ton that I did Pimp out by adding a Air Powered Hydraulic Jack and some of Swag Off-road stuff. This is just like a Professionally made Press Brake.

[@RathaSochenda]

🙏🏽

[@deltan9ne306]

6 minutes in to knowing you exist and an instant subscriber. Well done dude, well done!

[@RathaSochenda]

Thanks!

[@ffgghjssxcyj]

Incredible accuracy and design process

[@RathaSochenda]

Yeah it’s not too shabby for a homemade/garage setup.

[@ffgghjssxcyj]

@@RathaSochenda didnt you consider producing it and selling to people?

[@RathaSochenda]

@@ffgghjssxcyj just the plans for the frame and all the features I added or will at to the pressbrake tool to make it more semi-auto.

[@wolfgangsixl9283]

Very, very nicely done, Ratha! This is phenomenal!!!

[@RathaSochenda]

Thanks Wolfgang. See you in part 2!

[@Castorps_Shadow]

You are super inspiring, I wish I could do the same stuff like you!

[@RathaSochenda]

Thanks for the nice compliment. Im sure you can do anything you put your mind to! 🦾

[@Castorps_Shadow]

@@RathaSochenda What did you study if I may ask? I consider taking a course in welding or industrial product design. In what study can I learn to use CNC machines, autoCAD and welding at the same time?

[@RathaSochenda]

My background is mechanical engineering. But honestly I learned most of what I know just from watching KZbin videos and actually trial and error. It really is a mindset thing. I found the way to learn all three stuff like cnc , design, fabrication is to have personal projects to work on. I’m not sure if that helps answer your question but I hope it points you in the right direction. Pretty much self-taught but it helps to have online mentors you look up to and can ask questions for help. It’s amazing how many people are willing to help if you ask.

[@tkirkwood3366]

Awesome craftsmanship, thanks !!!!

[@RathaSochenda]

Thank you!

[@mikecrane2782]

Impressive design and build processes. Well done 👌 Subscribed and liked

[@RathaSochenda]

🙏🏽

[@jakemund8953]

Very nicely done!.. great job with everything and especially attention to detail!.. very nice and complete video!..

[@RathaSochenda]

Thank you!

[@ThisIsToolman]

Excellent job of both design and fabrication. This will be a DIY kit you’ll want to offer.

[@RathaSochenda]

Thanks. DIY weld kit is in the works for sure

[@koppecreative]

Your engineering is super impressive =) Love to see a fellow PNW-er killin the game!

[@RathaSochenda]

I appreciate it!

[@Ironfoxgates]

Very clean work. Your very sharp.

[@RathaSochenda]

Appreciate it!

[@Freetheworldnow]

Top notch video quality and build!!! I am extremely impressed by your craftmanship Sir. Respect! God Bless.

[@RathaSochenda]

Appreciate it!

[@sharpsticksnz4112]

awesome! Needing accurate bends I was thinking the same, cnc press brakes are too expensive for me but could I achieve repeatable bends with a normal press brake using physical stops.... you took it next level to electric stops to kill the power. Very cool! 😁

[@JordanBayer-k5s]

Never liked or subscribed to anything until now. Not a tech guy and don't understand the "youtuber"craze but I use it for "youtube academy" more than I do music even. If me hitting a button helps you in some way, well worth it. Liked and subscribing

[@RathaSochenda]

Appreciate it!

[@thiagodamatta2829]

Amazing job mate! This is exactly what I wanna do with and old 30t H press I have! Congratulations!!

[@RathaSochenda]

Nice!

[@Sloansteelsigns]

Great video, looking g forward to part 2 and building plans

[@RathaSochenda]

See you in part 2

[@derekcorey-goodman2489]

You deserve more views! Great content

[@RathaSochenda]

Appreciate it!

[@velaworks]

Waiting for part 2 have a blessed happy thanksgiving

[@RathaSochenda]

🙏🏽

[@el_kuks]

That`s really nice professional grade tool!

[@RathaSochenda]

Appreciate it!

[@EdgeofEternityBillCameron]

My compliments for a great and well thought out design! Really nice job.

[@RathaSochenda]

Thanks 🙏🏽

[@EdgeofEternityBillCameron]

@@RathaSochenda I’m looking forward to seeing more!! I subscribed. Lots of talent for sure!!

[@bernhard_derProtoTyp]

very cool! loved to follow along on instagram but cool to rewatch here again! thanks for sharing Ratha!

[@RathaSochenda]

Thanks for stopping by and watching

[@mts592]

👍👍 Awesome build and fantastic video!

[@RathaSochenda]

Thanks 🙏🏽

[@pangeachoppers]

Hell yeah! This is such a cool set up!

[@RathaSochenda]

Thansk

[@Bladd3]

WE need Part 2 pleaaaasssseee!!!!

[@jaashiik]

seriously impressive work. Thanks for sharing your builds and thought process, it’s so inspiring! Saw you’re a UW alum, go dawgs!!

[@RathaSochenda]

🙏🏽

[@beozzie690]

Nice design… keep up the projects.

[@RathaSochenda]

Thank you

[@pascalschmitt6293]

Very nice project man! Looking forward to each video of you 💪🏻 how do you achieve different bending angles?

[@RathaSochenda]

I’ll show you in part 2 or 3 of the video series. But in short I’ll adjust the thread bolt and record that depth specific for the angle. I’ll have a chart that I will create that will show what depth I need for certain angles I have per thickness. Mainly for me is 45 deg and 90s. If it’s some odd angle I’ll use a digital angle finder and bump the pressbrake pedal until I reach it.

[@traviswalker6831]

Nice work buddy!

[@RathaSochenda]

Appreciate it! 🙏🏽

[@jensonhartmann3630]

very rad man. your channel is fantastic.

[@RathaSochenda]

Thanks. Glad you like the channel

[@velaworks]

Awesome job ! Keep up the great content !! I may see what’s next you have and I’d plan on building one myself ! Thank you and your shop is super clean 👌

[@RathaSochenda]

Thanks!

[@rhokdatroll]

Very nice build 👍🏻

[@RathaSochenda]

Appreciate it!

[@KennyB9871]

Dude nice work! This is awesome!

[@RathaSochenda]

Glad you like it!

[@TBJK07Jeep]

Great video. You did a good job building it. I think I may have to build one.

[@RathaSochenda]

Thanks! It’s been working so good you just might have to make one!

[@chadcrawford1496]

You do awesome work. Love the videos

[@RathaSochenda]

Appreciate it. 🙏🏽

[@budmanzoom4441]

Nice work!

[@RathaSochenda]

Thank you!

[@SA-76234]

Looks fantastic. Thanks for sharing.

[@RathaSochenda]

Your welcome 🤗

[@jasonh3109]

Great video!!!! Keep up the great work! 👍🏽👍🏽

[@RathaSochenda]

Thanks for watching!

[@frrapp2366]

several years ago i made my press out of bridge banister-- 5in angle riveted together about12 in apart for the uprights and 12 in channel for the front and back of the table, and the top rails of the head,. I tried something different i made the hydraulic jack bracket (Head) so it slid along the top channels allowing me to press right next to the side(that had an opening between the angle iron legs) i was doing mostly farm parts straitening or pressing bearings out, the table was the only weak point as it is held by 2 3/4 in pins but they run through the front and back channels. never put enough pressure to bother them tho . like the repeatable of your design

[@1993hitesh]

Very nice design & execution as well what is tonnage capacity of the machine and how much max thickness that can be bendable .

[@RathaSochenda]

3/16” is what I’ve tested

[@norbyk3637]

Excellent.Finally I have seen what I wanted... Any time schedule for PART 2 of this video? Thanks.

[@RathaSochenda]

Hopefully soon…

[@norbyk3637]

Hi Ratha. I have tried to purchase and download the plan but the paypal is not working and there are some EU contries are not listed in the purchase selection. Any advice or other option You may recommend,please? Thank You very much indeed.@@RathaSochenda

[@RathaSochenda]

@@norbyk3637 for the build plans on international orders go here : www.etsy.com/listing/1575803667/diy-shop-hydraulic-press-brake-digital?etsrc=sdt

[@SierraScout2]

Great job!

[@RathaSochenda]

Thanks!

[@Frank-bh3cm]

Great work, when is part 2 coming?

[@RathaSochenda]

In the works… thanks for watching

[@nubtools]

Amazing work!

[@RathaSochenda]

Thanks brotha !

[@billdaniels5957]

Very nice job !!

[@RathaSochenda]

Thank you!

[@428Mario]

Nicely done

[@jesusmarte1880]

Excelente

[@michaelciavarella-fb2zc]

This is awesome , when will part two be out?

[@RathaSochenda]

Hopefully soon

[@blaisegoldman]

F'yeah! Awesome work! Im super inspired to build my own someday now! I have an air over hydro setup now with a Swag Offroad "break", its ok but I always felt it was lacking, this is the video I needed to see! Thanks for sharing!

[@RathaSochenda]

Appreciate it. I totally understand what you mean. Hopefully this video sheds more light on other options aside from what’s already available

[@formeisen6262]

Wochenende need also one to press 6 mm Stainless steel can you make one or laser us some sheets to build it for ourselves Best Regards!

[@minskmade]

this is brilliant.

[@RathaSochenda]

Thanks!

[@santory5788]

yes, awesome !

[@RathaSochenda]

Appreciate it! 🙏🏽

[@NorthernFabandMachineLLC]

Nice work!!

[@RathaSochenda]

Thank you!

[@drewnussbaum3756]

What is the retract time of this cylinder? Is it realistic in a production setting? I’m concerned with using a hollow-bore single acting cylinder due to how long it will take to retract far enough to remove the part, or reset to make the next bend

[@RathaSochenda]

For simple stuff I think it will work great

[@RamsesTorresLifevantageIndDist]

Solid

[@RathaSochenda]

Appreciate it! Stay tune for part 2

[@CharlesN-f6d]

Been waiting months for part 2

[@RathaSochenda]

Man you and me both! This holidays season been taking up so much of my time. Hopefully I can carve out some time and get part 2 up

[@rob-vz4wt]

Why not a c frame design like some of the commercially available ones? I made one similar to this many years ago, albeit much cruder. I would really like a c frame style.

[@RathaSochenda]

That would work too!

[@camwelch9948]

Great build. Will you have an approximate idea of total cost when you complete the press?

[@RathaSochenda]

I haven’t total numbers yet as I’m still working it but I’ll make sure to breakdown the cost in future videos

[@mackwilson9178]

@@RathaSochenda I also was curious about the ball park cost for this project? Any rough numbers? Thanks

[@RathaSochenda]

$3000 max

[@Randy_51_]

That’s awesome!!

[@RathaSochenda]

Thanks. Glad you enjoyed it!

[@imaginedesignbuild]

Really great, thanks for sharing

[@RathaSochenda]

Your welcome🦾

[@tomwilhelm67]

Great channel!

[@RathaSochenda]

Thanks

[@shaunos100]

Do you think you could do the same set up for a wider bender? I would say enough to fit 1800 wide material

[@RathaSochenda]

Most likely no… you will most likely have to run two cyclinder and get them synchronized

[@shaunos100]

I thought that would the case. Are you looking at making your own dies? There’s a with people I’ve seen who cut 16mm plate then weld them together to make a longer piece

[@daipower1]

I would love to build this, do vevor still do that ram as i cant find it. Whats the thickest plate you have bent

[@RathaSochenda]

Items used in this video: Cyclops Press Brake Tool: / cyclopsdesigns or www.ebay.com/itm/115064499037... Electric Hydraulic Pump/s: s.vevor.com/bfQHVv Vevor 30 Ton Cylinder: s.vevor.com/bfQh9M Anti-Wear Hydraulic Fluid: amzn.to/3Lt3YP9 Limit Switch: amzn.to/3qZNw1Z Return Springs: amzn.to/47X0YnM Linear Rail: amzn.to/3L2KLnp Digital Angle Gage: amzn.to/3QZTESt Leveling Caster 2200lb Capacity Set of 4: amzn.to/486WB9U a safe thickness would be 3/16" full steel sheet (23.625" long).

[@brettwilliford4350]

Do you have prints available for this? It’s perfect for my needs

[@RathaSochenda]

Yes please check the links in the video description for the blueprints

[@marcustomz]

Yessir! 👨🏾‍🏭

[@RathaSochenda]

Thanks for watching

[@bernhard5741]

Excellent Video! Just stumbled on your channel and just finished binge watching all your vids. Great presentation and full of useful info. Your channel is way underrated, this kind of quality deserves much, much more subs. I had planned to build a similar item, but now I will take advantage of your design: Now going over to your website to order the plans. Btw. Not sure where you are located (I assume in the US?), did you have any issues importing the Cyclops Design parts? Thank you, Bernhard

[@RathaSochenda]

Appreciate it. No issues importing from Tom over at cyclops design. Depending on what he has in stock it can take as little as two weeks or as long as a month for your press to arrive. But I can say it’s worth the wait especially if you compare cost of die/punch tooling here in the states.

[@RathaSochenda]

Also if you have any other questions please reach out to me on my contact page of my website. I'll be here to help!

[@Brian18741]

Excellent work👍

[@eddiewatson7192]

Great video where is part 2 lol

[@RathaSochenda]

Working slow on it 😅

[@Lik3dprinter]

Nice video

[@RathaSochenda]

🙏🏽

[@NoName-ml5yk]

Fantastic. Using the limit switch is a great idea. One thing I missed is how you can from 45 to 90 and back again without adjusting the bolt every time. Looking forward to the DRO.

[@RathaSochenda]

I’ll explain it in the video part 2 or 3

[@NoName-ml5yk]

@@RathaSochenda Can't wait. Thanks.

[@ethankincaid9022]

Just earned a sub.

[@RathaSochenda]

😎

[@aminjahanara1141]

Hi, how much is your unit prssure sir?

[@RathaSochenda]

30 tons

[@Dzon_Jacek]

👍

[@garth6351]

Freakin awesome. Going in my to do videos

[@RathaSochenda]

🤟🏾

[@332ARA]

What was the cost of build?

[@RathaSochenda]

Check out the Etsy link in video description. Then go under item details and I break down the entire cost to build this. Hope that helps

[@332ARA]

got it, thanks@@RathaSochenda

[@terrencewilsonpoopoo]

Part 2???? 👁👁️🙏🏾

[@RathaSochenda]

I know right 😅

[@曾志君-x3k]

兄弟，切割的时候注意防护颗粒物，带一个3m的防护面罩吧。

[@RathaSochenda]

sure

[@Sloansteelsigns]

I already started this build and just realized it's not made for a 6ft tall dude. 😂

[@RathaSochenda]

😂

[@manitobaman5588]

New subscriber from province of Manitoba, Canada. Excellent and practical design.I like your thinking on the preß brake with tooling from UK. THANKS FOR SHARING YOUR SUPPLY SOURCES AND IDEAS.

[@IRONMANMETALBILLDANKANIS]

Great ideas. Is there a part 2?

[@RathaSochenda]

Coming soon!

[@rob-vz4wt]

Why not a c frame design like some of the commercially available ones? I made one similar to this many years ago, albeit much cruder. I would really like a c frame style.