DIY: Installing & Testing Shower Panel Tower System

[@threeblackburn]

I agree, I appreciate the no non sense approach, and the clear guidelines. Keep these videos coming!

[@handytf]

Thanks, will do!

[@americanfreedom3416]

Looking for location of supply area specs

[@karinazakabluk3747]

what shower brand is this and how do you change the batteries?

[@robinharris1085]

Make sure you have Gardening gloves, eye protection, helmet, steel boots .

[@Wavelover33]

Headphones and knee pads too lol

[@exMelodi]

WTF

[@prestonian1066]

Helpful video thanks. BUT you made some simple and potentially very costly mistakes with the wall plugs. Never knock them into the wall with a hammer directly or you could smack the tile enough to smash it. Place the tip of the screw into the plug to knock it in when you get close to the tile. Either sink the plug beyond the tile or use a slightly larger drill bit at the start of the hole to accommodate the head of the plug, otherwise when it expands it can crack the tile. Finally, either set the torque really low on the cordless driver or do it by hand.

[@aljayy1225]

Where can we get the button. If it’s not working to turn it on? Or is it the battery

[@anthony402]

I have the same issues with mine

[@aljayy1225]

@@anthony402 it was the battery, it’s in a covering

[@anthony402]

@@aljayy1225 do u know where the covering is

[@aljayy1225]

@@anthony402 you will have to take the unit off the hook. Hold the shower unit and pull up to unhook it. After you do that, have someone hold it, while you trace the wires are the back, the battery should be in a black protective covering be careful not to damage any wires. After you replace the battery with two AAA I think, then you’ll see the light in the display, those batteries activate an actuator that allows the hot water to come out

[@anthony402]

@@aljayy1225 thank you very much I will give it a try.

[@SandraMaria-nt9ic]

Gracias por ayuda ❤

[@albetiziano]

Hi, where do you get replacement flexible pipes? The one that came with the shower panel are thinner and can’t find it on merchant.

[@mark.r8900]

Hi, does the hot and cold water hose already have built in washers? Or do you manually need to add washers yourself? Thanks

[@handytf]

built in

[@mhomadmadiyar2677]

brother how to connect the electronic power panel is it on AC power or DC power and how much watt

[@handytf]

it uses battery

[@vanessa4038]

I can't find the battery pack on mine??

[@alfredomontillavideos5739]

Excelente amigo😊

[@kumarcdo1]

Where you fix the heater

[@RajeshLingala-vu5hp]

Super ...exlent fitting

[@sandrahoyt2301]

Can you post a picture of the instruction that have the distance between the holes and mounting bracket locations, and sizes of the fitting and hoses that were used? Please and thank you.

[@adeelahmed3996]

How to increase water pressure on this system, specially if it's clogged with calcium built-up

[@mantiyaz1]

Thank you for the instructions!!! 👍🏽

[@somaaelsapak6361]

Great video thanks sir for that

[@handytf]

So nice of you

[@salahjabbar6199]

Where the light get power from

[@handytf]

battery

[@vitoperricelli8485]

Please show operation of panel once it is installed. Curious as to how the light works. Does it require wiring?

[@handytf]

The light is powered by battery, no wiring is required. The button on the side is used to turn on/off the light. The pain is when you want to replace the battery, you need to take off the whole unit.

[@pdh-ps9eh]

One part you left out that I don't quite understand. I assume that you remove the main shower head. Do you then pull up new pipes to go to the rainfall and water sprout. Do you have a video showing this step?

[@medtuning]

Thx so much for this video

[@Houstonpromasonry]

How does the led power on? I've seen models with led around knobs and head

[@handytf]

It uses battery. In this model, there is a red button on the side, push it in to turn the LED on.

[@reddhater]

It looks like you need the shower panel to get the water supply positioning out of the tiled wall and to have ot installed as per your desired height on the shower wall - otherwise you may be forced to install it at an inconvenient height. Instructions mention this, which means that you need access from behind shower wall or build shower walls after you get your shower.

[@handytf]

The water supply lines were specifically positioned for the panel before tiling.

[@reddhater]

Does not look flush to wall after installing it

[@handytf]

Actually it does. you can also caulk along the edge, but I would advise against it.

[@jhonkasanchez5820]

Cómo evitar que se mezcle agua fría y. Caliente

[@plumbingwithelectriceannag5144]

Supper bro

[@reddhater]

Hmm, bottom bracket location seems to be tricky / as the routing of the 2 water supply connecting tubes is not easy to ensure a flush installation Video shows several holes drilled before I guess at a less than perfect location… Best location of bottom bracket on the panel itself should be higher…

[@handytf]

This is to replace the old shower panel, the other holes were for the old one.

[@marcelaperonja9597]

No water pressure in that shower

[@handytf]

The water pressure will be low, if multiple jets are on, otherwise the pressure is pretty good. I just installed the second one in my house.

[@marywow9659]

They didnt show you the wobble

[@tuffbadger7342]

Easy enough to be fair

[@eljaydiver1]

I am still trying to figure out how to replace the batteries...I cannot get the compartment open!

[@orlandomonroy3494]

Hidro ducha

[@krishnatharu1463]

new video

[@ramsesvega5066]

3:20 that’s the dumbest thing I have ever seen

[@gatoborracho4572]

It's ok 👍..just needed to use a rubber hammer instead

[@howtodo8728]

😂

[@alinalee6241]

Great, and we have heater built-in type smart shower panel or just shower panel tower system , pls contact us if you are interested.

[@nageswarao.nnagu.5397]

My.pohnenambar