Tap to unmute

DIY kitchen scale using load cell & HX711

  Рет қаралды 10,995

Will Donaldson

Will Donaldson

Күн бұрын

Пікірлер: 15
@laithacademy
@laithacademy 2 жыл бұрын
I'd love to learn how to build this! Do you offer private lessons
@danielhenderson7050
@danielhenderson7050 3 жыл бұрын
Cool project 👍
@Mailanias
@Mailanias 9 ай бұрын
Can I use an Arduino nano esp32-s3 for this?
@fiqueporaqui
@fiqueporaqui 3 жыл бұрын
Hello, the right project I was looking for. Will be using it to weight wild birds when they land on a dish with seeds . Two questions if I may: 1) About the two push-buttons, the one in pin 1 of the ATMega is the reset, the other on pin 16 (PB2) is it the Tara? 2) Is it OK to use pins 8 and 22 for a ground bus? Or it is only to show on the diagram.
@antoniobautista5302
@antoniobautista5302 3 жыл бұрын
can your calibration code for this be used on a 50kg load cell? the ones that look like a square?
@BOON140163
@BOON140163 4 жыл бұрын
Hello sir, how do you tare it ?
@saschak4618
@saschak4618 2 жыл бұрын
How do you make your wiring diagrams? They are so beautiful especially for smaller circuits.
@WillDonaldson
@WillDonaldson 2 жыл бұрын
With this software: fritzing.org/download/
@HothamsApiary
@HothamsApiary 3 жыл бұрын
Cool video! I want to build a scale for my beehives, but I don't want to have them powered on constantly as I will really only need to check the weight weekly. Will the scale always show zero then when I switch it on or can I write the code so that it only tares once and then from that point on always displays the load? Is my question clear?
@WillDonaldson
@WillDonaldson 3 жыл бұрын
Yes, the scale will always show zero when turned on. If left on for a long time the measurement may drift by a few grams, this is not a precision device, merely a fun hobby project. I am not sure what you mean in the second half of the sentence "can I write the code so that it only tares once and then from that point on always displays the load". Note that you will be able to find cheaper and more precise scales from manufacturers, but if your application is just for fun and learning then definitely make your own!
@HothamsApiary
@HothamsApiary 3 жыл бұрын
@@WillDonaldson thanks. I don't understand why zero will be displayed when applying load and then switching on the power. I thought that during calibration the factor is saved and will be applied on the values received by the amplifier. The arduino code could use that value each time the device is powered on. I will still try to figure it out. Thanks again for the great video.
@jasonleonardo3641
@jasonleonardo3641 4 жыл бұрын
hello sir... ca you help me for my laod cell i dont know how to use it. My load cell is 200 kg maximum.
@alexmarod6438
@alexmarod6438 4 жыл бұрын
👍👍👍
@soussiamouhtadi7423
@soussiamouhtadi7423 4 жыл бұрын
Hello, Thank you for this video Please can you help me solve my problems about my Arduino project Sincerely 🙂 🙂
@Allexz
@Allexz 2 жыл бұрын
yes.
#161 Measuring weight using an ESP32, a strain gauge, and a HX711
13:55
ССЫЛКА НА ИГРУ В КОММЕНТАХ #shorts
0:36
Паша Осадчий
Рет қаралды 8 МЛН
Как Ходили родители в ШКОЛУ!
0:49
Family Box
Рет қаралды 2,3 МЛН
🎈🎈🎈😲 #tiktok #shorts
0:28
Byungari 병아리언니
Рет қаралды 4,5 МЛН
How to use encoders (Optical, Hall Effect, Quadrature)
20:44
Will Donaldson
Рет қаралды 114 М.
How to use HX711 with Four Load Cells
16:18
Robot Research Lab
Рет қаралды 52 М.
Four Steps to Flawless Wire Joints (How to Solder)
11:45
Will Donaldson
Рет қаралды 710 М.
#55 50KG Load cells revisit #2 - Finally working
10:12
Tim's Electronics Lab
Рет қаралды 17 М.
Fast PASTA: converting an HX711 module to 80 SPS
9:16
Davor Virag
Рет қаралды 8 М.
Photolithography on Silicon with PCB Chemicals
25:31
ProjectsInFlight
Рет қаралды 59 М.
ССЫЛКА НА ИГРУ В КОММЕНТАХ #shorts
0:36
Паша Осадчий
Рет қаралды 8 МЛН