Do you have a build list or parts list available? Great work!
@anetastal96642 жыл бұрын
Amazing!!!
@OlegValk_Rc_JustAircraft8 ай бұрын
hi, what is the cutting speed and power for 3mm plywood?
@user-sd5hl9zv9l10 ай бұрын
please tell me how you connect laser power supply to board ?. thanks
@dubeayiokorie45462 жыл бұрын
Very impressive!
@positronic-lab2 жыл бұрын
Thank you!
@BrianMaynardLetsDoThisThing Жыл бұрын
Nice project
@AnassRennoun.2 жыл бұрын
Hi this is such a nice work , i'm working for a school project and i want to know what is caracteristics of this co2 laser tube thanks in advance
@positronic-lab Жыл бұрын
it's 40W CO2 laser tube from aliexpress pl.aliexpress.com/item/32846491493.html?spm=a2g0o.order_list.order_list_main.31.fe641c24fv4iYd&gatewayAdapt=glo2pol
@AnassRennoun. Жыл бұрын
@@positronic-lab hahahahah i finished my studies thanks anyway
@positronic-lab Жыл бұрын
@@AnassRennoun. A little bit late I suppose 😅
@dustblowingman Жыл бұрын
Those safety glasses would do nothing against the lasers radiation
@positronic-lab Жыл бұрын
Those are rated for much stronger lasers, CO2 lasers have mostly radiation in the invisible spectrum, so goggles can be transparent. Bought them from www.survivallaser.com/
@ruidolfo97116 ай бұрын
potence and cost of all components?
@gskinnerg2 жыл бұрын
Great work!
@positronic-lab2 жыл бұрын
Thanks 😊
@ckgconcept8672 Жыл бұрын
bonne initiative une co2 laser Diy😊 …néanmoins sur cette vidéo quelques détail manquent ..le trait de coupe est trop épais ..pourquoi (laser cutter seulement ) ??
@positronic-lab Жыл бұрын
Yes you right, line was too thick, i had a lot of trouble with mirrors alignment.
@voc0072 жыл бұрын
Have list of materials you have used, and what controller are you using ?
@positronic-lab2 жыл бұрын
I am not tracking it, this is an iterative design / experiment. Controller - Arduino mega with ramps 1.4 and marlin firmware.
@jasongriffith7298 Жыл бұрын
Where did you get the mounts for the laser tube? Looks great!
@positronic-lab Жыл бұрын
Quick design in Fusion 360 and printed them on my Ender 3 v2
@ckgconcept8672 Жыл бұрын
tu les fabrique avec une imprimante 3d ou avec ce que tu as dans les tiroirs . 😌
@lateforwork2922 Жыл бұрын
What driver board are you using to run the stepper motors?
@positronic-lab Жыл бұрын
It's A4988 www.pololu.com/product/1182
@ckgconcept8672 Жыл бұрын
je te conseil des nema 23 avec un contrôleur approprier au final si tu veux exploiter au mieux ta machine 😊
@jean-baptistetetia64872 жыл бұрын
Very good job , your point is big . I think your are to low or your focus is wrong, Because usually cut wood in two pass was easy
@ckgconcept8672 Жыл бұрын
Bonne déduction ..mais Tout dépend l’optique de focalisation qu’il a prise pour monter sa machine les hauteurs sont différentes selon les optiques
@narovanjanaharyfanomezanaa1023 Жыл бұрын
I am planing to build mine as well, That would be great if you can share the files, thank you in advance.
@positronic-lab Жыл бұрын
Unfortunately i don't have any useful files, it was built without any plans. I was creating it step by step, solving one problem at a time. Lest say it was incremental build. I'm planning to publish part 2 soon where i will describe it more.
@AlansInventions Жыл бұрын
@@positronic-lab Nice job! Can you share the source of the laser tube?