DIY Tensioner/Pulley Kit replacement on 2008-12 Mercedes Benz C300
Пікірлер: 29
@jackzap2 жыл бұрын
Car was squeaking and your video helped me change the belt. Thanks!
@briansamara9587 Жыл бұрын
Great video! DIY went well and you saved me a pile of cash! Thanks!
@marcusscott61992 жыл бұрын
Great video very detailed thanks 😊
@mastercdiychannel80632 жыл бұрын
Thank you.
@thongsoukmingsing1715 Жыл бұрын
Thanks for making this video
@MrNini18262 жыл бұрын
You are the best 👌 you explain very good...I check ✔ another video 📹 they just waist your time .. but you know very well ..thank you
@mastercdiychannel80632 жыл бұрын
Thank you
@thomasmend43212 жыл бұрын
Thanks for the help. Really
@CarlosGarcia-kr5ph Жыл бұрын
Very useful thanks
@daveycrockett9447 Жыл бұрын
You should compress the tensioner and place the set pin in place BEFORE loosening any screw on the belt tensioner pulley- otherwise you won’t have access to the other bolt.
@daveycrockett9447 Жыл бұрын
Never mind - you addressed this. Great job on the video.
@mujotagani10492 жыл бұрын
Counter-clockwise brotha
@Daniel-pj9nm2 жыл бұрын
Is there a specific tightness I should screw the bolts when I replace the pulleys or is it just as tight as possible?
@daveycrockett9447 Жыл бұрын
You have to be very careful NOT to overtighten. The block is aluminum- so it’s easy to strip the threads if you are not careful. I used blue lock tight and 18 ft/lbs
@josecarreras7749 Жыл бұрын
So my pulley broke from the back lip and ripped my belt to shreeds is there a certain limit to how tight the pulley gotta be
@rjkulman8990Ай бұрын
torque is about 20 nm ( always good to know torque values, and apply them accordingly)
@makennajames7732 жыл бұрын
What would cause the belt to slip off after replacing the top pulley?
@mastercdiychannel80632 жыл бұрын
Makenna, it could be many factors such as loose bolts, bad pulley, bad belt to a bad tensioner. Make sure to route the belt to the right direction/diagram. The belt will need to be tight so it wont slip off. I hope you can fix it.
@Rob-ln-Real_Life2 ай бұрын
Installed incorrectly
@panseycain70862 жыл бұрын
Hi, can you please tell me if I have a bad water pump or is it just the serpentine belt. Thanks.
@mastercdiychannel80632 жыл бұрын
Pansey, I won't be able to tell without seeing a video of it. What is wrong with the car?
@rjkulman8990Ай бұрын
remove belt, listen for bearing noise, same as other pullies, if leaking or noisy --- replace
@everetteramey5723 Жыл бұрын
I must have a dirty belt; I replaced all the pulleys and check the other ones and chirping..
@kennethmay6343 Жыл бұрын
Have you looked into this yet? I’m about to try to replace the Idler pulley on mine and see if it still is squeaking..
@everetteramey5723 Жыл бұрын
@@kennethmay6343 I haven't changed the belt yet; someone told me to check all the other pulleys by spinning them or pulling up and down on them and they didn't feel loose.. I KZbin 303 aerospace protectant it quieted that belt for 2 weeks.. I'm going to clean the pulleys then spray the belt down again.. That belt doesn't have any breaks in it. When I get time I'm going to clean everything.. I been working on my other vehicle to get working . KZbin 303 aerospace protectant and how to clean idler pulleys.. before getting a new belt research which ones are of quality. Some belt will tend to chirp more often than others..
@Rob-ln-Real_Life2 ай бұрын
Turn the car on with the belt off ..if the chirping stops you know it’s a pulley