DIY USB Tester | How To Make Mobile Charger Tester

[@jhill4874]

Would be better with narration, but the schematic helps.

[@muctop17]

Sure DIY is fun But I have 3 of them with showing Voltage Amps and Wattage for $10 from Ali And lots more with Micro-USB and USB-C and Bluetooth and already built in in a cable plug......

[@hermanwooster8944]

What a song/video combo. Just a boy, his horse, and their DIY USB Tester.

[@super-8]

an current meter would be give better informations ^^

[@TARIQLAB]

Yes

[@old_gibbon_]

Этот тестер всегда будет показывать ~5v и быстрая зарядка не будет через него работать))

[@TARIQLAB]

да, это просто проверить, работает ли usb-порт или нет

[@ВАсяПупкин-ъ5щ4ц]

@@TARIQLAB смысл от вольтметра тогда, просто светодиод поставить.

[@talhaijazprojectlimited5295]

Aoa bhi ak question ha kindly answer manay 12 v ak supply hall road say us ki wire touch karay wo automatic off ho jati us may ka cheez laghi ha wo off ho jati ha,send email picture send krta ho, market may kisi ko protection supply ka nhi pta,manay kits leni ha mujay batie may kasay check kro yhe supply protection wali ja jab wire output touch ho off ho jye

[@TARIQLAB]

Mery channel description main Whatsapp hai

[@fawaz400]

ابغى زيها من وين

[@Techno0070]

Very creative

[@BirdLoverBulgaria]

Can I make it to measure current?

[@TARIQLAB]

Only for voltage, Watch this video on my channel kzbin.info/www/bejne/q4mzdn2Obdhkq9U

[@BirdLoverBulgaria]

@@TARIQLAB Thx bro, i will try that

[@Inspire_Tok]

what are those pins that you connected to male usb?

[@TARIQLAB]

+5v & ground

[@ericklein5097]

they look kinda like dupont pins from breadboard jumpers

[@ericklein5097]

actually I think they are resistor legs

[@Inspire_Tok]

@@ericklein5097 i think they are just stripped wires idk

[@Zyghqwyv]

I thimk they are clipped off led legs

[@worldnewswithali4656]

How

[@chunchun722]

better buy USB voltamp meter than making this one, it's more expensive

[@ericklein5097]

what? If you have a piece of proto board I'm sure you could scavenge a USB male and female port from somewhere meaning you have to spend $2 on the voltmeter. All the connections were made using legs of components like resistors and caps which an also be scavenged. 5 minutes dumpster diving and you could probably get all the pieces except the voltmeter if you were willing to do a little fabrication on a PCB meant for something else

[@fighter-l4n]

عالی

[@vch74507]

Ещё и дороже вышло чем обычный

[@madbat5480]

Выглядит просто но блин без контролёра это работать не будет я думаю

[@amitk5060]

But now link?

[@bobrtik1332]

Один вопрос , зачем ?

[@TARIQLAB]

проверить напряжение мобильного зарядного устройства

[@beach7912]

Quindi? A cosa serve?

[@TARIQLAB]

per verificare che il caricabatterie mobile e la porta USB funzionino o meno

[@beach7912]

@@TARIQLAB se metto in carica lo smartphone e si ricarica , funziona, se non ricarica , non funziona. Magari può essere utile per chi ripara smartphone tutti i giorni. Bravo cmq. 😉

[@plexricardo]

Cadê o esquema

[@TARIQLAB]

dentro do vídeo

[@dimitri.m]

there is an APP for that !