How to Replace a 2004 Nissan Titan Climate Control Module

[@DIYHomesteadProjectsDIYHP10]

How to Replace Valve Cover Gaskets on a 2010 - 2014 Ford Transit Connect or Ford Focus kzbin.info/www/bejne/nHmskpyur6ulY7c

[@ericfritz1519]

THANK YOU!!! You gave excellent help and saved me $700. I went to a U-Pull-It salvage yard and found a truck that had the module but no knobs! Someone took all the knobs (which I did not need) BUT left only the plastic part I was searching for. I could not believe it! Total cost = $0 and literally because of your video only 6 min to fix. Totally appreciate you making this video.

[@DIYHomesteadProjectsDIYHP10]

Excellent!

[@goliac492]

Very helpful sir!!! Nice job.

[@DIYHomesteadProjectsDIYHP10]

Thanks for watching!

[@markashlock9017]

Anytime I can make a repair for the price of a month or two car payments, I consider it a no brainer! Good job and wise decision Bruce!

[@DIYHomesteadProjectsDIYHP10]

That’s a great point Mark! 👍🏻

[@MikeS-c9q]

Great video, thanks! It might be helpful to know that if you can't find the exact controls for the Titan, you can use the controls from a Pathfinder that has basically the same climate controls with front and rear a/c and heat! I just did that, you just have to cut off the rear ac/heat part of the clear plastic base that the controls are attached to, AND, use a drop of glue to anchor the right hand end of the clear plastic assembly because you won't have a screw hole. I just did this and finally I have control of the drivers side temperature setting.

[@crimepunishment-ot2yl]

Really pretty easy! Looks doable. Glad you explained your toothpick JB Weld fix bc that's going to be my intention - something along those lines. Great video.

[@DIYHomesteadProjectsDIYHP10]

Glad it was helpful!

[@sewerdawgs]

This helped me fix mine. Saved me alot of money. Just used super glue. Thank you for tip

[@DIYHomesteadProjectsDIYHP10]

Glad it helped!

[@crimepunishment-ot2yl]

Yes! This is my problem - just the knob! Thanks

[@DIYHomesteadProjectsDIYHP10]

Happy to help!

[@richnvick9281]

Your Titan looks friggin immaculate.I got a 04 and it doesn't look anything close to yours. I got broken plastic everywhere and I try to take care of it but it's so fragile

[@DIYHomesteadProjectsDIYHP10]

Yes their plastic does get quite brittle with time. Our truck mostly sits and only gets used when we do something that requires a truck. Gas is just too expensive these days.

[@brutalragegaming]

Hello im wondering if i can send you an email of a part i found on the nissan website for this exact problem i dont know if this is the part or not

[@DIYHomesteadProjectsDIYHP10]

I would recommend you call a Nissan dealer and confirm the part number with a Nissan parts department person. That's how I found the correct part for my truck. I don't know the part number, they just ordered the part they told me would fit and it did thank goodness.

[@calivalley9056]

I’m in a bit of a rabbit hole, my A/C flow keeps kicking off and on, no flow, but still adjustable when it is on. I ordered a blower resister but I don’t think that will fix it. What was your actual symptoms when the climate control model began to fail? I need to the check the system pressure and the pressure switch still.

[@DIYHomesteadProjectsDIYHP10]

My issue was a broken plastic knob. I could not change the fan speed. Unfortunately you can’t just change out the knob only.

[@calivalley9056]

@@DIYHomesteadProjectsDIYHP10 Thanks for the reply, I think my control model isn’t the issue. I think a may be low on pressure due to a leak. I have owned it since new, it’s just now starting to break, but better to fix than buy a new truck. New prices are insane.

[@DIYHomesteadProjectsDIYHP10]

I agree, new prices are insane! I wish you the best!

[@calivalley9056]

@@DIYHomesteadProjectsDIYHP10 Turned out to be the blower motor resistor. Easy fix.

[@DIYHomesteadProjectsDIYHP10]

Nice! Good to hear you were able to get it fixed easily.

[@phonotd]

Nice job Bruce. Would it be a hard job to replicate the part concerned if you had access to a 3D printer?

[@DIYHomesteadProjectsDIYHP10]

That is a good question. I don’t know the answer though as I have zero experience with using a 3D printer. I’m sure it could be done if you know what you are doing.

[@phonotd]

@@DIYHomesteadProjectsDIYHP10 maybe a business opportunity for some enterprising individual who has a 3D printer, or access to one.

[@DIYHomesteadProjectsDIYHP10]

I agree!

[@jimtucker7005]

Thank You :-)

[@DIYHomesteadProjectsDIYHP10]

You're welcome!

[@TheMamonti1]

700.00...... I would drill a hole in the center of the fan switch and make a extension to go from the actuator , through the top and put a knob on it.

[@paulmakresias3881]

Can't you just replace the switch

[@DIYHomesteadProjectsDIYHP10]

You could but nobody sells just the switch

[@CHRISFREE84]

Playing game

[@Getagrippeople2witnesses]

Omg A Speedometer that Works Not so much Infiniti QX56 Hahaha 😆

[@kevinraney2935]

30 bucks at a pull apart yard.

[@DIYHomesteadProjectsDIYHP10]

That’s definitely an option but I don’t want to be chasing parts and changing this out two or three times a year. Also I’d have to travel to find a salvage yard as we don’t have one like that in the area where I live.

[@kevinraney2935]

@DIYHomesteadProjectsDIYHP10 Yep. I got lucky. I got one 10 min from home.

[@DIYHomesteadProjectsDIYHP10]

That's literally a gold mine! 👍