do this to unscrew the (broken) disc bolt, you'll be smarter than the rest

[@lorenzoghinelli7018]

The idea is nice if you got an old tapper and you prefers to use with this purpose in stead of sharpening it and using it for what is made for. Otherwise you can buy a screw extractor that is a commercial tool made exclusively for this purpose ;)

[@Andyspeeder7]

Bolt extractors are crap, never in 40yrs have I seen one actually get a tight snapped bolt out , this guy could probably have hammered the square end instead, my preferred extraction tool is a torx bit hammered in

[@Andyspeeder7]

Torx bit hammered in saves time and works

[@2pist]

I just finished this exact same repair. I tried heat, torx bit, flat head pounded in, nothing worked. I drilled out the center 4mm and was able to use a bolt extractor.

[@fernandokosin2643]

Bastava ter a chave Allen do tamanho correto, pois a cabeça do parafuso não estava espanada!!!

[@jameskiehn5595]

Use what you have and come up with a way to make it work. Not the way I would have done it but good thinking 👍well done

[@syafiqkuy6911]

Cerdas,untuk keadaan darurat,tapi lebih mudah pakei screw ekstrakor

[@geoffankrett7012]

Hammering in a good quality star bit gives the same result 👍

[@dietmarscholz161]

👍nice Idee

[@wongkexing3342]

Its a waste of tapping tools instead on other way & normally l use star socket hex to open the stud coz its much easier & save a lot of time rather than grinding the tools if u all dont believe u all can try use it or slightly bigger in size of the star hex

[@naimayoga7230]

Waaah...kalo saya sih sayang sama handtapnya bang...

[@莫忘初衷-o7z]

GOOD👍👍👍

[@SterSun-ft9og]

If it is a brake cylinder sliding iron column rusty stuck cannot be remove Is there any way to remove it ?

[@KuswantoOke]

Lebih aman stelah di bor pake mata obeng getok, di bikin segi empat tapi pjokan sudut pesegi empatnya di bikin tajam, malah lebih kuat, maaf hanya saling berbagi

[@baspratama5202]

Itu kalau kategori mudah, kalau macetnya udah parah, gak bisa diapa apain tetep akhirnya dibor terus di tap ulang.

[@deil9665]

"Torx" можно забить.нагреть,wd-40. Ну а потом и инструмент портить😄

[@adhimix6114]

wajib beli tab dulu....!😁🙏

[@firmansah4794]

Mantap om ilmunya

[@mikespain8655]

Tighten up the vice on work bench, it is loose.

[@werkudoropandowo]

tukang las beeres jhon... 10K slsai

[@kenaja7863]

Kalau gak bisa kebuka gimana ngebor nya baut di las akan megeras besi

[@werkudoropandowo]

@@kenaja7863 bawa sini. biar kamu tahu

[@opengauk2948]

Buka sendiri skrang mh bos ?

[@KuswantoOke]

Kalo yg bener bener keras itu mata taf bisa patah bosss😊

[@warnadisedet101]

baut yang susah dibuka karat harus ditetesin VPC dibagian karatnya 😆😆😆😆😆

[@kurosekirei]

タップは折れやすいから止めた方が良い。

[@АндрейЛетов-с8ъ]

и чего? Этому способу более 50 лет. Ты видимо сам много чего не знаешь.

[@叫獸-x8c]

整個白眼到翻過去

[@duboshlt8646]

Красавчик!!!!

[@yen1761]

👍🏻👍🏻👍🏻

[@TaiPham-yh9ki]

Sao ko sit miếng nhớt hay rp7 vô

[@progaragechinskiemotorki]

dobre to :D

[@АлександрМельниченко-й5в]

Торксы есть для таких издевательств. А сломается метчик ну это следующее видео.

[@bat35h]

👋👋👋👋👋👋👋👍👍👍👍👍💯

[@Wendizer]

Я сломал мечик в болту остался кусок. Спасибо канеш, но не очень.

[@lakhtaG64]

я обычно такую шляпу, выкручиваю битой звёздочкой. есть мелкая звездочка и крупная, вот крупной самое то. шестигранники она крутит на раз👍🏻

[@jesusmarques8805]

Parei de assistir nos primeiros 1.47 minutos, uma mancada cade a chave correta.

[@firdausfirdaus7031]

di bawa ke tukang las beres

[@ДмитрийДмитрий-ц5н]

Ну что ж так нудно?

[@thangthanh5989]

qua OK

[@whothis4403]

не культурно инструмент портить.

[@alaahaleem36]

It will make you dumber to break down a machine in order to extract a bad screw

[@erkoblack2502]

Lah kesuen

[@nitarismayani4571]

Hmmmmm