Does Your Arrma Typhon 3s Wheels Fly Off?? East Fix!!

[@ClayFunk]

Thank you for this video, I experienced this today. You were spot on, sir!

[@davidwong3637]

I just fixed mine by following your tips and advice, thanks……

[@oilyexploration2085]

Cheers great vid will do mine this weekend wheel came off with bearing doing a run after work today 😢

[@dboogeman2002]

I still can't believe they refuse to do this from factory

[@gamercat7004]

I haven't done this to my typhon, and it's been a week having this rc and soon have to check this no wheel hasn't come off yet.

[@NCmountainsYouTubeChannel]

I got five packs through my. Arrma Kraton v5 6s. A rock got stuck in the top of the Center diff cut it almost in half. I’ve never been to a skate park I didn’t even know we had a skateboard here lol We’re going soon. Luv my Arrma now it’s upgraded. Steering servo center diff 30k.

[@MIKEC2000]

Just got one and they are all Low strength Locktite but going a head and doing them in blue anyway

[@jeffarab4947]

Just pulled off the wheel and the screw. I see the inside screw loose lmao. Thanks man

[@Νικόλαος-ο5δ]

What screw is? Hex?

[@bakihanma644]

How do you get the blue thread locker down to the screw???

[@simonq9406]

Nice Vid. Mine has not done that yet

[@Νικόλαος-ο5δ]

What screw is it? 2mm hex?

[@jeffarab4947]

Hilarious even tho I seen this video. IT JUST HAPPEN TODAY WHEN I WAS DRIVING REAR WHEEL FLEW OUT

[@cg3399]

I have a 3s senton and my left rear has came off the past 2 times ive ran..2 different wheels and I don’t really do any big jumps just mainly track style runs. The hex is spinning inside the wheel and kinda stripped out the plastic around the hex too. Do you think this is due to the same problem in the video?? Im about to tear the truck down anyway for cleaning and drive/diff gear grease and needed to find a fix for the wheel issue. Thanks

[@theRCelement]

Sounds like you might have the same issue in the video as well as not tightening the wheel nut tight will cause the wheel to come loose and strip out the plastic hex in the wheel

[@cg3399]

@@theRCelement that might be it i put a washer behind the nut and it didnt come off. i just tore mine down and greased both differentials and the drive gear..i ran it yesterday and it ran super smooth..but my universal joint at the end where the hex goes on the left rear axel is super loose. its floppy. i know they swivel and are loose anyway but theres zero tension so im thinking that might be the problem. are you familiar with the steel blue/red ones on ebay? thinking about buying those if there good quality

[@krashkingrc9715]

Nice very important information that definitely stinks when that happens

[@carlosmorean2909]

Hey bro , i tried to pull out the first screw on the hexagonal but is too tied . So I can’t do anything 😰 Any advices ?

[@Thestudiedtheist]

If you cant get the screw out, how do you apply thread lock to it?

[@theRCelement]

Oh lol. That might be a good thing if you can’t get it off. Did you break something where you need to remove it?

[@Thestudiedtheist]

@@theRCelement nah, im working on my diff. I needed to replace some bearings on rear diff

[@quettequette9436]

I guess I need to see it work after he use thread lock and tighten the screw. Maybe he's a man of his word. Ijs for a beginner showing the full breakdown is better than telling me about it

[@theRCelement]

I see your point. Thanks for watching though 👍

[@JMCD8050]

A fix from the East.

[@TechWizMaster]

this is the only real downside to Arrma i have the big rock and it's also loosing wheels left and right for various reasons...and the wheels are trash on them the plastic is too soft imo.