Down Stream Injector How It Works And Troubleshooting Problems

Down Stream Injector How It Works And Troubleshooting Problems
Show you how to find problems if the down stream injector is not working.
We use down stream injector to apply soap with our pressure washer. You have to use low pressure to apply the soap.
General Pump 5-8 Gpm Chemical Injector 100776
amzn.to/2MA4Fcl
General Pump 3-5 Gpm Chemical Injector 100775
amzn.to/2vRr4s7
3/8-Inch Stainless Steel Quick Connect Pressure Washer Adapter Set
amzn.to/2OOS2rh
XJET M5 HIGH PRESSURE DELUXE VARIABLE LONG RANGE NOZZLE # 13 (3000 to 4000 psi)
amzn.to/2Pou07N
#chemicalinjector #Downstreaminjector #soapinjector
HELPFUL RESOURCES
Have Any Questions?
[e-mail]
▶️ Check Out This AWESOME Website For Amazing Content About Pressure Washing 💰💰💰💰💰💰
www.pressurewashhelp.com/
Check Out My Christmas Lights Page 🎄🎄🎄🎄
www.christmaslightshelp.com/
WASHLIFE TEE SHIRT
www.amazon.com/dp/B07F3RBK7L
▶️ Need Help Setting Up A Roof Pump?
www.pressurewashhelp.com/roof...
▶️ Need Help Setting Up A Window Cleaning Unit?
www.pressurewashhelp.com/wind...
▶️ Need Help With Pressure Washing Business?
www.pressurewashhelp.com/busi...
PRESSURE WASHING CHEMICAL INJECTORS
✅ Down Stream injector 5-8 GPM www.pressurewashhelp.com/Down...
✅ Down Stream Injector 3-5 GPM www.pressurewashhelp.com/Down...
✅ XJET M5 www.pressurewashhelp.com/xjet
HOSES AND QUICK CONNECTS
✅ 3/8-Inch Stainless Steel Quick Connects www.pressurewashhelp.com/Quic...
✅ Pressure Wash Hose www.pressurewashhelp.com/3/8P...
✅ O-Rings for 3/8" Viton (10 pack) www.pressurewashhelp.com/Orings
✅ Super Swivel 1/2” www.pressurewashhelp.com/Supe...
✅ Hose Reel Solenoid Cole Hersee www.pressurewashhelp.com/Sole...
✅ Hose Reel 12V PUSH BUTTON SEALED www.pressurewashhelp.com/Push...
PRESSURE WASHING GUN
✅ 5000psi/12gpm By Suttner www.pressurewashhelp.com/Sutt...
✅ Ladder Saver Long Range Nozzle www.pressurewashhelp.com/Ladd...
✅ 4000 PSI BALL valve www.pressurewashhelp.com/HPBa...
✅ Mosmatic Pressure Washer Swivel - 4000 PSI, 3/8in. www.pressurewashhelp.com/Mosm...
✅ Jrod Nozzles For 5-8 GPM www.pressurewashhelp.com/Jrod
✅ Jrod Sleeve www.pressurewashhelp.com/JRod...
ROOF CLEANING SETUP STUFF
✅ Delavan FB 2 12V, 60 PSI, 7.0 GPM ROOF CLEANING PUMP www.pressurewashhelp.com/Roof...
✅ Grote 82-2100 Push Pull Switch 75 Amp www.pressurewashhelp.com/Pull...
✅ 40 AMP Circuit Breaker www.pressurewashhelp.com/40br...
✅ Kuriyama Kuri Tec PVC Spray Reinforced Hose, www.pressurewashhelp.com/Roof...
WINDOW CLEANING SETUP
✅ Delavan 7800 12V, 60 PSI, 2.0 GPM www.pressurewashhelp.com/Wind...
✅ Grote 82-2100 Push Pull Switch 75 amp www.pressurewashhelp.com/Pull...
WINDOW CLEANING
✅ Water fed pole www.pressurewashhelp.com/Wate...
✅ 40 AMP Circuit Breaker www.pressurewashhelp.com/40br...
OTHERSTUFF
✅ Hudson Float Valve www.pressurewashhelp.com/Hudson
✅ Honda GX630 and GX690 20mm Drainzit www.pressurewashhelp.com/Drai...
Disclaimer: Some of these links are affiliate links where I'll earn a small commission if you make a purchase at no additional cost to you
#PressureWashHelp #JasonGeiman #RoofCleaningHelp

[@boriskey7841]

such a great explanation. I use my pressure washer once a year at home but I learned quite a few just from this video. Thanks Jason!

[@kingofpressurewash]

That’s awesome dude thanks for watching

[@ROIPW3000]

Thank you Jason! My DSI would not work. Your trouble shooting check list was what I needed to to make it work! I had the arrow pointing in the wrong direction. A rookie mistake for sure.

[@ptbgrow1262]

Great videos that help out all the bigginers

[@kaloosh2639]

dude this video really helped me out alot,was needing some education on these injectors ,,your videos and channel keep being a go'to for pressure washer informational stuff,I need one will check your site soon🌊

[@ryanduren2739]

I have a 10gpm had to go to a 2.5 it works pretty good.

[@stevedetts7975]

Excellent video. Clearly understand difference between ball valve and Xjet. Thanks for the information on cost and mix.

[@kingofpressurewash]

Thanks for watching

[@_1ben]

thank you for sharing

[@damienbrimelow9840]

Thanks mate

[@christophermassaro9952]

Thank you sir for the video.

[@Puckthepolice]

Great explanation thanks

[@SalishSavage-1]

Man you are so awesome thanks for all the great content

[@kingofpressurewash]

Thanks for watching. If you have any questions don’t hesitate to ask

[@pastorlugo121]

Great video. Thanks.

[@kingofpressurewash]

Thanks for watching

[@Idontwantaname313]

The man. The legend

[@tyrell3535]

thanks man.

[@chrisracer2007]

Mosmatic 29.020 stainless you might like it

[@justrusty]

Thank you. Very helpful.

[@kingofpressurewash]

Thanks for watching

[@kingofpressurewash]

Thanks for watching

[@scarecrow6926]

I have been using the same injector for Years also for the chlorine ball. Also on the inside of the inlet there is a jet that screws in and out when you start losing suction Power and Water start spraying back out. Also sometimes when the ball starts getting stuck it's where the jet goes bad on the end. And you have to replace it. It's on the inlet side of where the water goes through

[@423LoveRboY]

Im having those problems now with my pressure washer troy bilt briggs and stratton

[@vicchavez4947]

Very informative

[@kingofpressurewash]

Thanks for watching

[@troywilliams2503]

I get about 6 months running a 2 step wash with acid and soap I put a ceramic ball in mine

[@richardnichols2064]

I notice the fitting has a rating but if you put a inline valve on the soap line you can adjust the amount of soap suction you get and save some money on soap by better dialing in the strength of your soap.

[@SokoCrypto]

When you go from downstream injecting to pressure washing with the surface cleaner do you disconnect the downstream injector and just connect the high pressure hose directly to the pump without the downstream connector?

[@brettebert10]

Can you use this exact set up for a Simpson pro series 4000 psi 3.5 gpm gx270?

[@AnthonyRodriguez-go4uw]

Great information. I just started using my downstream injector. But I have a question!!! How do I regulate the chemical suction. It draws too much soap. It used up 5 gallon tank of soap real quick. There's a lever in the middle witch way is to open or close flow. ????? Thanks in advance

[@kingofpressurewash]

On your question about the switch I don’t know but I do dilute my SH down with water. Like I will do 1 gallon water and 1 gallon of bleach

[@tomshuppert4860]

Ty

[@kingofpressurewash]

Thanks for watching

[@stevemiller9269]

Hi Jason my name is Steve my question is will bleach eat up water hoses over time

[@nicholashalvis5376]

I’m using a remote system the hose that goes to my downstream injector keeps blowing off and I don’t know why. Any suggestions would help. Thanks.

[@JunkNGrind]

Great Explanation Buddy. I’m Pretty New to Pressure Washing. I’ve Done about 10 TOTAL Jobs for My Own Company. 👍🏼. Subscribed I make Scrap Metal Videos and Junk Removal, Pressure Washing, Demo Jobs Here & There. Thanks Man.

[@frankpirrone6032]

Will it still pull chem if you remove spring and ball? I turn it off anyway and don’t use pressure to turn it on and off but the ball sticks once in a while.

[@djdelisle1953]

Always keep extra on your truck

[@extremepowerclean]

Thanks for the information, just wondering, if you connected 2 downstream injectors together with 2 separate suction lines would you get a stronger mix through or does it not work like that? Thanks

[@michaelh.6020]

rdmnailman, won't work! Too much back pressure...

[@jonashcraft9267]

What injector would I need for a 3400psi with 2.5fpm flow?

[@tomflora6040]

With the downstream chemical injector attached, what happens to the original injector? Is it still pulling vacuum? Should it be plugged? Thanks

[@Kgoutdoor]

Sometimes I go weeks without using mine cus I do this as a side hustle. Mine continues to not pull chemical. Almost as if it’s clogged up but I pull it out and make sure it’s clear. The smaller port tho where the hose goes there’s like a ball there so I can’t tell what’s going on. It’s very annoying.

[@NoName-be5ir]

I’ve been days trying to get my pressure washer to downstream. It a new machine, 4gmp . I’ve checked for leaks with both new injectors. The arrow is going towards the line. A 100 ft line. It has the soap injectors that came on the machine up steam with tag no bleach. It’s not drawing soap either. Is this a machine issue. I’m getting 4000 psi on the gauge, it fills a 5 gallon buck up at the minute mark . I’m just lost with it. Ordered the first off amazon with a metering knob, second one from my local pressure washing supply house. Im using a black soap tip I started with pressure all the way down and nothing so I give it a little bump, nothing little bump nothing no fluid moving. Any suggestions? Is there something on the pump it self I need to change. Thanks a lot

[@seattleprowash5464]

any idea why anytime I use my DS injector it pops the o ring in my pressure washer ?

[@judahmartinez8552]

Those prices have gone up pn dsi. Its the time of sleepy creepy joe, God please take me back. Just subscribed i made the rookie mistake on the arrows 😆

[@kingofpressurewash]

Haha, don't worry, we've all been there with the arrows! But hey, at least you're subscribed now and that's what counts!

[@abrahamhenson7380]

Ok, i have a question. I have been using a down stream injector and just getting strait 12.5% SH in a 5 gal bucket and using a j rod. I want to get a chemical tank but i want wondering exactly what you are talking about the fitting on top of the tank. Its about about <a href="#" class="seekto" data-time="290">4:50</a> in the video. Can you put up a pic or explain exactly what you mean. I would like to do this myslef. Im tired of having 5 different 5 gal buckets strapped to my trailer.

[@kingofpressurewash]

Here is a video explaining how we install it into the tank kzbin.info/www/bejne/qXyzmJ13gad8iqs

[@fpplsoftwashpressurewashin8757]

Just starting out and I'd like to take my chemical injector and used it as sort of an xjet at the gun. I've removed the ball and spring from the chemical injector hoping that it would draw more soap. Will this work for me?

[@kingofpressurewash]

Probably not

[@Igor-q3f]

Thank you. I use a pressure washer and a 5 gallon bucket with a ladder saver second story nozzle. When I apply soap and the small injector hose is in bucket it reaches higher, when I rinse and the injector hose is out it doesn’t reach the same. What do you recommend to do? Thanks.

[@kingofpressurewash]

Put it in a bucket of water

[@DetailEnthusiast]

8/16/19 you made your 10k!!!

[@kingofpressurewash]

I know Thanks

[@COFFEE-e3p]

@@kingofpressurewash you the man , stay awesome mate !!

[@howardtoob]

I have a Simpson 3500/4 belt pump and an injector after the pump. Can I move it to the wand end of my hose for more chemical and less water? Thanks

[@kingofpressurewash]

That would be called and xjet

[@tgeorge78]

Jason, I’m having trouble figuring out what thread size I need to put a QC coming out of my pump outlet. I am not sure if I need a 3/8 or an M22. I have a Simpson Power Shot 4400 psi, 4 gpm. Thanks.

[@tgeorge78]

Now I’m thinking m22

[@davidweatherford6592]

Jason have you ever used a duel barb injector for roof? Would this be strong enough mix for doing a roof using injector without having to use 12v or air diaphragm ? Thanks

[@kingofpressurewash]

David Weatherford I don’t think it would be strong enough still you would be looking at 2.5% in that area

[@davidweatherford6592]

Power Washing ok, thank you for the reply 👍

[@toddlunsford4073]

Nope it’s not near enough Of a SH percentage to clean a fought sufficiently

[@amberferrer4563]

It’s there

[@ferminmoguel859]

Hey man. I have a question for you. Why my downstream injector is leaking? Thank you!

[@rckintz]

Why does my downstream injector shoot water out of the top it and fill up the bucket of cleaner that it’s drawing from.

[@bluewash5601]

Looks like teflon tape on your quick connects. I'm starting to have some leaks with my teflon at different locations. When replacing the teflon it is totally broken down. Do you have any other suggestions?

[@MrGavisconCR]

First go with a 2.1 injector for SH on a 4000psi, 4GPM machine. What ratio should that be?

[@kingofpressurewash]

I think it still 10 to 1

[@davidweatherford6592]

Jason, do you recommend plastic or stainless connections on softwash hose reel? Thanks

[@austin2187]

Would love some help. I have a 4gpm machine and I got a 2.1 downstream with a jrod & 200 ft hose If I hook up up gun with jrod directly to downstream I can pull chem If I hook gun to 100ft hose I can only pull a little chem (.5 gallon in 2.5 minutes) but with no jrod only with no tip in gun 200 ft I can’t pull any chem in any way Please help educate me

[@kingofpressurewash]

What size hose? What if you take the gun off? Guns can be a issue

[@KPKDETAILINGNEPA]

I run a mobile detailing business and I want to offer pressure washing also... I already have a 4000psi and 4gpm unit to use but I was thinking of adding and 2nd reel and hose and downstream the chemical so I dont cross contaminate but is there any way for the chemical to make it's way to the pump with down streaming

[@kingofpressurewash]

Nope there is not

[@artbentley4887]

Hi Jason, I have a new injector on my 4.2 gpm pump. It’s. a 2.1. When I let off the handle, water flow backward into my SH tank. What do you think the problem is

[@kingofpressurewash]

Yes the ball is gone out of the injector or was never put in

[@TheTomimler]

Hope you see this. I installed a down stream injector on my 2500 psi unit. I noticed the water flowing INTO the soap container rather than soap flowing OUT. The level in my test bucket went up instead of down. It has a metering valve which I have wide open. What would cause that??

[@toddlunsford4073]

You have the injector installed backwards! Make sure you have the arrow pointing in the direction of your pressure hose. Rookie mistake

[@alxnils1]

Can the injector just be on when you are using the machin for normal pressure washing?

[@kingofpressurewash]

Yes it can. It may restrict the flow a little bit of

[@vincechiarantona8440]

Mine is shooting water out... pressure washer losing pressure. Can I just remove this

[@worawutwongbuncha9862]

Can you tell me please?, I can’t connect it work.

[@Painfulwhale360]

Do you guys mix surfactant with your 50/50 water and SH mix?

[@kingofpressurewash]

Taylor Albaugh yes

[@Painfulwhale360]

Silly question, but how long do you guys keep the chemicals on the house before you rinse it off?

[@kingofpressurewash]

Taylor Albaugh 5 -10 minutes just don’t let it dry on it so weather will have a factor on it

[@thfishing3775]

how do I rinse with low pressure while the injector is hooked up? I constantly have to walk back and forth and shut the machine off, walk back release the pressure, walk back un hook the injector etc.

[@kingofpressurewash]

This right here is how I do it. 3 Way Valve With Downstream Injector To Making Last Longer

[@kingofpressurewash]

kzbin.info/www/bejne/mn-oZoGDq9djps0

[@BusinessAcc4me]

Do you need a chemical hose for downstreaming or a regular pressure hose will suffice(clean it with water after every use)?

[@kingofpressurewash]

Are you talking about the small hose for the from the downstream her to the Chemical or the actual pressure washing hose

[@BusinessAcc4me]

@@kingofpressurewash actual pressure hose where the gun is connected.

[@kingofpressurewash]

Ricky Ricky pressure wash hose and rinse house cleans it out

[@antoniorivera1311]

So if you use this to dilute the chemicals, should I put direct chemical on the bucket since the pw is going to dilute it?

[@kingofpressurewash]

Antonio Rivera yes so sodium hypochlorite comes in 12%. The downstream injectors will dilute it 10-1. Now you can clean at that ratio but it’s a little strong and can maybe kill plant life at that ratio. We put 50% water and 50% SH in a bucket the downstream that mixture

[@antoniorivera1311]

@@kingofpressurewash strongest I can get here in my area is 10.5%

[@norm6135]

How about if I soft wash spread my solution and then use the pressure washer to rinse

[@kingofpressurewash]

Yes you can do that

[@norm6135]

Hello and thank you for all your infos I very much appreciate it. I would like to know your preference in downstreaming either using the injector like this video or using a Proportioner?

[@chicagolandsoftwash1934]

How much SH do you need to clean a vinyl house and remove the algae?

[@kingofpressurewash]

Tommy Jurek 3-5 gallons

[@chicagolandsoftwash1934]

Thank you... Which do you prefer? Down streaming or xjetting?

[@kingofpressurewash]

Tommy Jurek down streaming

[@artbentley4887]

Also, when I do a draw test, I’m pulling 1 gallon of SH to about 13 gallons of water. Is this normal?

[@kingofpressurewash]

Depends on what injector you're using

[@jamespope6940]

Question, I have a 1.8 chem injector 2-3gpm and it’s <a href="#" class="seekto" data-time="1201">20:1</a> ratio, how should I mix my 10% pool essentials

[@kingofpressurewash]

Straight

[@jamespope6940]

Power Washing you don’t think straight will damage plants or grass or the vinyl? I’m using it with a 3200 psi 2.5

[@kingofpressurewash]

James Pope not at 20:1 That puts you at 1% You can add a little bit of water but not much. .75% is about as low as you can go and not take forever

[@jamespope6940]

Power Washing ok online it says it has a 20% draw that’s what 20:1 means correct? Or is that something else

[@benderprofessionalservices9018]

Pressure Wash Help what does a 20-1 downstream injector put 12.5 at the gun. How to you do the math equation. Wonder if I need a 2.1 injector. Tku I’m shooting it on stucco and vinyl fences.

[@SomCountysFinest]

i have a Landa pghw 8gpm @ 3500 or so... I have a 2.3 injector but i think my Jrod has too small of soap tips.. im not getting the draw i should i think im running a 40 for soap.. do i need to go to a 60 for it to work because my Landa MHC that was a 3.8 gpm with the 2.1 injector ran flawlessly with the jrod i have.

[@SomCountysFinest]

can you email me please.. [e-mail]

[@kingofpressurewash]

Yeah I’m pretty sure that a gallon a minute you should be at the 60tip. Because I believe up to 5 gallons a minute you’re actually at the 40 tip.

[@SomCountysFinest]

@@kingofpressurewash Thanks man just waiting for them to come in.. Def put this week on hold!!

[@kingofpressurewash]

Chris Hess And that stinks. So where do you end up ordering them from

[@SomCountysFinest]

Power Washing my supplier in NJ that I get everything from. They should be in by tomorrow. Been doing business with him for a while. Called Gateway Cleaning Equipment. He’s only about an hour from me so it’s easier then doing everything online imo

[@DetailEnthusiast]

Ive got a 4400psi 4gpm and with it came a dsi that reads 3.5gpm. Called company and they had no idea how it got in there. Is it compatible with my 4400? What would be the ratio and is 3.5 enough for roof cleaning? Haven't tried it yet.

[@kingofpressurewash]

You can't use a pressure washer to do roof cleaning.

[@JohnstonPettigrew]

@@kingofpressurewash here in South Florida (tile roofs).....everyone does.

[@kingofpressurewash]

JohnstonPettigrew even on tile roofs you can soft wash

[@JohnstonPettigrew]

@@kingofpressurewash yes, you can certainly soft wash......and pressure wash... both are quite common practice

[@michaelschroder6071]

@@JohnstonPettigrew in Florida 90% of the people aren’t licensed, insured, or even have papers LOL. Don’t bring a surface cleaner on a roof..

[@georgemullin7772]

Mine is literally brand new and won't work on a champion 3200 washer

[@randolphpayne8249]

does it matter it if it faces up or down

[@kingofpressurewash]

No it doesn’t

[@michaelrasbury]

My Briggs and Stratton SpeedClean 2800 PSI has worked so well however now the chemical injector only draws from my soap/chemical bucket when the unit is off. When the engine is not running it works like a champ! When the engine is on and running properly, it will not draw from the bucket at all. I purchased a replacement injector, ball, spring, and hose and after installing no change. I took off the manifold and checked the o-rings and valves and all looked clean and clear. I removed the unloader valve and it seems to work as expected. I am using the correct black nozzle attachment. I've tried lowering the water pressure at my faucet. Again, works exactly as expected with the engine is not on. Any ideas how I can get it to work again when the engine is on for that little extra pressure for applying chemical/soap?

[@kingofpressurewash]

Make sure the gun is opening up all the way

[@michaelrasbury]

Pressure Wash Help Thank you for your response. It seems to be opening up just fine. There’s plenty of water pressure coming out of the gun. Could this have anything to do with the unloader valve needing adjustment? I wouldn’t really know how to tell if the gun is opening up all the way? There seems to be no blockage.

[@kingofpressurewash]

Michael Rasbury If the gun is not opening up all the way it will build too much pressure which would cause it not to draw. If you took the gun off and started the machine see if it’s pulling that way. Obviously make sure you’re holding onto the hose when it started

[@jamespope6940]

Question, I have a 2.5gpm Simpson 3200 pressure washer I order a 2.1 3-5 gpm injector, it’s sucking the chemicals way too fast, what can I do? Smaller syphon line? Any tips.

[@kingofpressurewash]

you can dilute it down

[@jamespope6940]

Power Washing meaning mix like 2gal pool essentials and 1 gallon of water?

[@kingofpressurewash]

@@jamespope6940 we use 5 gallon bucket with 3 gallons of sh to 2gallons of water you may be able to do 2 gallons sh to 3 gallons of water

[@jamespope6940]

Power Washing ok thanks! Is the 2.1 the hi draw? Should i just buy another one that draws less?

[@kingofpressurewash]

@@jamespope6940 i would just do it with a 5 gallon bucket and mix it. Even on our big trucks we do 50 gallons of water and 50 gallons of 12.5 sh

[@rowdyharris3688]

Two questions: 1. How much do you charge for house washing? 2. The SH rusts it and you say you go through them exceptionally fast. Why don't you keep a second tub full of water and drop your hose in it to suck water through and rinse your gear?

[@kingofpressurewash]

First question here is a video going over pricing kzbin.info/www/bejne/hounqKGdnrNsm7c 2 question you can use a 3 way valve so it pulls water instead of soap and this is a good thing to do. amzn.to/2VocMNI

[@ilawrence]

Hi my Injector says 2.1 That means for every two gallons of water it pulls 1 gallon of SH.

[@kingofpressurewash]

Nope just the size

[@ilawrence]

Thank You Sir.

[@jamespope6940]

Can I use well water to pressure washer a house

[@kingofpressurewash]

Yes you can

[@kingofpressurewash]

May need to take brakes so house pump don’t burn up

[@kingofpressurewash]

@Andso Itbegins i would give it like 15 minutes breaks so it can cool down

[@charlestuozzo4747]

Did you just say I could draw more soap with a 2.1 (for may 2.5 gpm home gamer washer) on my 8 gpm pump? So I could be around 2% or better? Yes I'm a newbie. LOL

[@michaelh.6020]

Jason, nice vid however, look at the camera lens when videoing, not the monitor screen. Also, switch to a chlorine ball rather than the steel! I'm running a stainless SSS high draw injector with a chlorine ball which has 2yrs on it and no problems thus far!!! Downstreaming at 700psi through 200' of 3/8" and it'll draw the balls off of a goat...

[@michaelh.6020]

First Choice Services, no doubt about that! It's so tempting to look at the monitor screen.

[@bluewash5601]

Michael thanks. I'm looking into the SS with chlorine ball injectors.

[@ddentici]

Hahaha balls off a goat...

[@michaelh.6020]

I was hoping someone would get a kick out of that! Obviously, it won't literally do that however, its got some serious pull...

[@Vulcan5911]

Can you explain the chlorine ball, stainless sss a little more with downstream. I'm interested in knowing a little more. Thanks.

[@jonadam1552]

Can you make a upstream injector into a downstream?

[@kingofpressurewash]

Jon Adam I don’t think so but I’m not sure

[@heavymechanic2]

My first time using a downstream injector, could not make it work . For anyone reading this, its a 2.1mm orifice and the consumer pump did not have enough GPM to overcome the detent ball to pull a vacuum and I ended up using a pump sprayer.. After finishing the job, ordered a 1.8mm (rated for 2-3 GPM pumps) and will try again. I was unaware the 2.1 has a minimum flow rating of 3GPM and more than a typical consumer model pressure washer can deliver. *not in the business

[@kingofpressurewash]

Make sure you have it plumbed right and you have the right tips and your J Rod

[@heavymechanic2]

Thanks for a reply, the orifice was on the pump side and the arrow directed toward the hose, even tried removing the wand and nothing happening at the injector tube.

[@577buttfan]

There ain't really much that can go wrong with a ball, spring,and brass if you keep it clean.. maybe the spring gets stiffer with time exposed to the SH?

[@kingofpressurewash]

The spring will go rustout with SH

[@577buttfan]

@@kingofpressurewash thanks for your reply

[@jamespope6940]

So i just hooked up my new injector... it pulls chemical when the pressure hose is not hooked up but when I hook it up it won’t pull chemical

[@kingofpressurewash]

James Pope how much hose you have on it

[@jamespope6940]

Power Washing I’ve got 25ft hose

[@kingofpressurewash]

James Pope what nozzle on gun also will it pull soap with out gun on end of hose

[@jamespope6940]

Power Washing haven’t tried yet I have the 2.1 injector on my 3200 2.5gpm. I just unhooked the pressure washer hose and it stared pulling but when plugged back up and pull trigger with black soap tip in it would do nothing.

[@kingofpressurewash]

James Pope just use it with no nozzle. I say it’s the gun not opening all the way or creating to much pressure

[@td6460]

SH does not kill mold.

[@MrDefenseless]

you're funny.

[@samfordhw]

Hi please look more at the camera its a bit spooky

[@vikto07081980]

This set was so nice I purchased a second set when I ended up adding a second 50’ hose to my set up. kzbin.infoUgkxG9W58byG1ZFYaD32YfLk74_TrU5mNkXV Only down side hooking two hoses up with quick connects you end up with a 6” ling section of fitting would be nice if there was a union type fitting instead that would save a huge chunk of material in line with my hose. But that’s just how I set it up. I go between a 50’-100’ all the time. Otherwise mine hasn’t leaked once used Teflon tape of course and have been running these since early spring 2022!

[@joeblow8023]

$$&&&& QUESTION WHEN YOUR NOT USING THE PICKUP TUBE FOR SOAP IS THE barbed FITTING SUPPOSED TO Be CAPPED OFF IT LET UT SUCK AIR??????????

[@kingofpressurewash]

Suck air or use a three way valve and pullvwater from watertank

[@marcusbrown8739]

Can't see video fully

[@dwaynearthur2804]

Hey dude im over here!! Marco! Polo! Marco !! Polo!! What the fuk r u looking at???

[@BP-uy6fc]

Holy cow spit it out

[@amberferrer4563]

It’s there a Soap injector that will work whit 200 ft of hose

[@kingofpressurewash]

Amber Ferrer the one above one doed

[@harlemfashion1561]

I did a big dirty house today then boom no soap was coming out I was so angry took me 5 hrs clean a house …

[@dwaynearthur2804]

You been drinking?

[@kingofpressurewash]

Nope

[@applejacks971]

You mentioned the T is $16, and $30 with the quick connects...and you are replacing them every 6-8 weeks, "$30 every 6 weeks isn't bad"...do you not realize you can unscrew the quick connects and put them on the new T? Thus it should only be $16 for the new T every 6 weeks

[@shellcrackerlover5889]

Wait a minute, you absolutely want to get that chalky crap off of vinyl siding. You said not to?? Makes no sense..explain.

[@kingofpressurewash]

That chalky stuff is oxidation. You will never get it all off with pressure. It takes a special chemical to get it off

[@shellcrackerlover5889]

@@kingofpressurewash Gotcha, thank you!

[@mikeyj990ify]

I never have one of these that works as it should. And not talking a cheap piece

[@joongtreez9402]

I have no idea what he s talking about.... no disrespect

[@motomyrtle]

Get the Biden ads off your video dude!

[@kingofpressurewash]

I agree let’s figure out how to do that