I enjoyed watching and learning how to get the Makita drill chuck unstuck. It was very direct and easy to follow. Thank you!
@josephhansen1320 Жыл бұрын
Thanks so much this video has really helped with my drill repair
@dannyf49957 жыл бұрын
A perfect video. Thanks. I just wonder who gave a "dislike" to this video?
@tomthompson74005 жыл бұрын
me
@elmerovero75284 жыл бұрын
@@tomthompson7400 why?
@tomthompson74004 жыл бұрын
@@elmerovero7528 Start with the heres how to drill through your hand bit work next on the hitting with the side part of a dead blow hammer end with the if only i had some vise grips part is that enough or do you need more ?
@thecrowsblow12 күн бұрын
Haters gotta hate
@pierrejoubert77545 жыл бұрын
Thank you for the well illustrated advice. For a normal electric drill, you have to use a spanner to immobilize the threaded shaft that holds the chuck before striking the L key.
@elultimo1025 ай бұрын
I took my electric Makita outside with the hex key in place, held it to the ground and put it in reverse. It did unscrew the chuck when the hex hit the ground, when hammering didn't work.
@pierrejoubert77545 ай бұрын
@@elultimo102 Thank you for your advice Elultimo!!!
@conanhayle6 жыл бұрын
tried all you recommended but to no avail ,I had to cut off most of the old chuck with a hacksaw and then heat up the remains with a blowlamp (gas torch? USA ) only then did it come off . I must say I was very near throwing the thing in the trash (rubbish ) UK . took 2 hours.. and broke 3 impact driver bits trying to remove that centre screw .. even when I drilled out the screw the chuck would not give up and move.. thank goodness for heat .. I felt like had won the lottery when the chuck finally came off.. Conan, UK
@TheSteve1574 жыл бұрын
I had to do the same but I used an angle grinder and cutting disc
@HeyV636 жыл бұрын
I was listening with headphones and that knocking at the very beginning (in only one earpiece) had me jumping in my seat like "how the hell is someone knocking at my WINDOW? On the first floor???" Don't do that!
@leviblank18866 жыл бұрын
Ahaha its 1:15am here and i just went to my door shook af because of it lmao
@SuperJuiceman156 жыл бұрын
@@leviblank1886 same!
@JokesOnU4 жыл бұрын
Just found this channel to hopefully fix my Bosch drill. Awesome video and kick ass intro!
@OndraN922 жыл бұрын
Thank you so much! Finally I can get chuck of my drill (even it was a brand new Makita, nothing else helped).
@papabrewsky6 жыл бұрын
Retaining screw is left-hand thread. GOOD TO KNOW!
@96aspinlane7 жыл бұрын
Thanks, was about to give up but worked 1st time thanks
@niteshade2955 жыл бұрын
Thanks your advice was very helpful for me I have nearly given up on my drill. Thanks Again
@ibringthelastwords13583 жыл бұрын
Wow Nice tips! Keep up the good work and more power to your channel. Thank you 😊
@KefashWhite4 жыл бұрын
The fright at the beginning of the video made me pee myself just a little thinking someone was in the house knocking on the drywall.
@apmeehan5 ай бұрын
Haha yeah fucking hell, could have sworn it was real
@jenvallance89457 жыл бұрын
thank you - it worked for me very quickly!
@boozebeard95014 жыл бұрын
Putting this here just in case it helps someone. I was watching this because I thought my chuck was damage, motor was spinning but chuck did not move. Turns out my drill was somehow stuck between 1 and 2 speed, making sure it was fully switch to one of the speeds fixed it. Good thing too because I couldn't for the life of me get the chuck to come off with the hammer and alan key!
@petwaitress Жыл бұрын
Omg thank you! I feel silly now
@creativechannel61482 жыл бұрын
Thank you , liked and subscribed
@Ty_ThatGuy2 жыл бұрын
Great video. Would this be the same method for a Hyper Tough brand as well? ? My drill has had the same problem for 2 days now.
@J.T.191342 жыл бұрын
I grinded a bolt down to 3 sides. Locked it in the chuck, put a socket on my impact driver. Much easier then hitting it with a hammer. IMO
@scottbaker4314 Жыл бұрын
I would love to see how someone would remove a stripped chuck on this 20v Porter cable drill I have the internal gears are stripped so it just slips even with air gun on it and yes the screw has been removed
@joaodepina71174 жыл бұрын
Great video. It worked for me..
@drkastenbrot2 жыл бұрын
Im trying to upgrade the chuck on a brand new drill and the retaining screw itself is not the problem. The chuck is screwed on so tight, I assume there is loctite involved. I could not get it to move no matter how hard I hit the allen key and I even damaged the chuck in the process. Can I take apart the gearbox from the inside to get the shaft out?
@RupertRichardson3 жыл бұрын
Excellent video. My keyless chuck had jammed - shut of course - so I had to grind it off, but the video showed just where to grind, and the bit about the wrong-handed screw was essential, as was the advice on cooling and heating. Both were needed, so maybe you did it right. Tip: if your drill is a DeWalt, it has a Torx 20 screw. If you try to undo it fresh out of the freezer, the Torx bit shatters...
@brandonjay51465 жыл бұрын
This makes me happy
@spLiffyFOUR204 жыл бұрын
you have a picture of a drill with it closed in the thumbnail, mine is closed... and its stuck. how do you get it off if its closed all the way?
@classydays433 жыл бұрын
Hit the beak with a hammer while trying to turn the chuck body to the open position.
@royceanderson33895 жыл бұрын
Great Video.
@ccdirecttvdllc52464 жыл бұрын
i have a Makita XPH07 and i got the screw out, but the chuck does not want to screw off. I;ve got it in the drill setting on no.1 as another video suggested. It is turning, but not coming off.
@LawrenceRhodes2 жыл бұрын
I have an old Ryobi D45C which uses a two part chuck with a thin nut at the bottom of the chuck. No retaining screw. The jaws are seized. How does one remove an old chuck like this?
@carlosyreynagatorres78133 жыл бұрын
I dig this beat
@astrozombies3 жыл бұрын
Hey thanks man it worked
@victoryfirst28782 жыл бұрын
Can I buy a Jacobs keyless chuck for my drill motor ?? Where can I get that Sir ??? Thanks
@gerbenhoutman93487 жыл бұрын
Worked for me. Easy as pie
@jimroadhers6 жыл бұрын
my 3/8 completely seized and i had a half inch that fit the anvil threads. so far so good...the 1/2 inch seized too after i lube it. gee wiz
@johnoh16675 жыл бұрын
I have a drill chuck with the reverse threaded screw removed. The CHUCK seems to be stuck and I cannot use a normal method to remove it. I think some one may have locktited the chuck but as it was newly purchased it may simply be caused by a seized thread. How can I remove the chuck? Good Video but doesnt apply to my problem.
@RiffRaffMama.5 жыл бұрын
Is the replacement retaining screw just a screw or is it a particularly special screw that I need to obtain from the manufacturer?
@classydays433 жыл бұрын
You can pick up drill chuck retaining screws online.
@georgemorgan945 ай бұрын
How about if the problem is that the jaws won’t tighten so I can’t get an Allen key locked in there to hammer on?
@skateboard4zero Жыл бұрын
I’ve removed the retaining screw, but can’t get the Allen key to undo the Chuck, it’s just turning the motor of the drill. Drill clamped to bench, low gear, drilling mode, 10mm Allen key and hitting anti clockwise. Any ideas?
@HM13.3 жыл бұрын
My driver drill's chuck has misaligned jaw (2 stucked at lower part, 1 at middle part). This method still unable to fix my drill issue. Do i need to replace the entire chuck?
@nosby305 жыл бұрын
Thanks man! I fixed mine thanks to this video :)
@dillwiggle26 жыл бұрын
How come when i whack the allen key the drill wants to spin and wont get the chuck loose ? Am I missing something here. The drill is on low speed (1) and when i turn the allen key by hand first it stays really tight until i whack it with the hammer and the drill slowly spins. Is this just a really stubborn chuck or any other suggestions ? It is a newer Makita brushless hammer drill.
@DrJeffConklin4 жыл бұрын
Make sure the clutch is set to the Drill setting. That locks the chuck and drill together, so if one spins they both do.
@RiffRaffMama.5 жыл бұрын
Ok, I'm going to ask the obvious question - if my drill is the problem.... how can I drill it?
@fabianore804 жыл бұрын
Mmmm, with another drill.
@RiffRaffMama.4 жыл бұрын
@@fabianore80 Are you going to run over with one for me? Because people aren't often in possession of more than one drill.
@fabianore804 жыл бұрын
@@RiffRaffMama. Sure, will be my pleasure, where do you live, if you are far to from me, I have a solution for, you can take your drill, go to neighbor ask for share his drill for 2 minutes and do the job in his home, then give back it and say thanks. I am sure nobody will reject to share for a few minutes.
@RiffRaffMama.4 жыл бұрын
@@fabianore80 Dude, you've no idea where I live. My closest neighbour is kilometers away!
@fabianore804 жыл бұрын
@@RiffRaffMama. By this reason I have two drills, one cordless for easy and fast jobs, and other corded to do rough tasks (stone, concrete). You should to consider to buy another drill too.
@zizoumonk102 жыл бұрын
How do you know when you’ve drilled out enough of the chuck screw?
@ThePsvan4 жыл бұрын
Ok, that knocking sound effect creeped me the eff out. With headphones it sounded like someone was knocking on the door. Too real dude.
@zhenyuliang44493 жыл бұрын
It sounds to me like someone was knocking on the wall so I checked three times because I restarted watching this video three times.
@valthalin76135 жыл бұрын
My makita teeth wont close, they are locked all the way open so bits just wobble inside. the chuck it'self wont turn much, just barely moves one way or the other and makes a snaping/locking in place sound when I turn it clockwise. sound like it should make that sound. luck the chuck is slotting into something. sorry i'm not a tool buff not sure how to explain it better. Do I still need to bust it open like this?
@raisagorbachov4 жыл бұрын
My harbor freight battery drill jammed. I saw the little screw and couldn't undo it so I did as suggested - tapped it with a long nail. The screw vanished and the chuck started working again.
@RomboutVersluijs3 жыл бұрын
WHy do none of them state in what mode the drill needs to be, is i guess it needs to in remove or counter clockwise, right?
@MuftakisWorld4 жыл бұрын
hello the problem is my device has 2 chuck its black & decker cordless 14.4v driver/drill i have screwed out the screw so easily but the problem with the 2 collars after turn one it goes to point that stop and start turning the one behind it so i tried to use 2 wrench one fix one and another wrench to loose the another collar but here is the big problem it doesnt loose whatever i push it so how to replace this doomed chuck i am stuck now with broken jaw teeth??!!
@losttribe19937 жыл бұрын
Nice vid
@sashanealand8315 Жыл бұрын
also if my chuck is stuck how will I tighten it down on an alan wrench?
@davidplummer24736 жыл бұрын
There seems to be a million videos on removing a chuck, or fixing a chuck with a bit stuck in it. But I have twice accidentally opened a double-sleeve keyless chuck too far and it won't close again. Are there any videos on how to fix THAT?
@FIXTechGuides6 жыл бұрын
Hi David, that's one problem that I haven't seen yet. I could not find any videos concerning it also.
@zackphillips66488 жыл бұрын
What do I do when my drill chuck is seized in the smallest size (1/16") not (1/2") like in these videos?
@FIXTechGuides8 жыл бұрын
Squirt a bit of WD-40 or any other kind of lubricant on the chuck and let is set for a minute. You can put some vise grips on the chuck and try to bust it loose with a hammer.
@dustinwestmoreland12004 жыл бұрын
I agree with the other comment the thumbnail shows a closed Chuck. that is my situation how do you fix that
@greg683x2 жыл бұрын
What if your chuck wont tighten? I’d imagine the Allen wrench trick wouldn’t work in this case
@roncroom33466 жыл бұрын
What do you do if you have a drill bit already in the stuck chuck?
@DrJeffConklin4 жыл бұрын
See above
@flaplaya5 жыл бұрын
Couldn't we just use a tool to remove the screw? I want to fix my drill not break it worse. Thanks.
@tilgaztizi91635 жыл бұрын
You're right, watch this video instead kzbin.info/www/bejne/o5K9eWV6h9yXbbs
@rumbero4215 жыл бұрын
Hi, My problem is with a Porter Cable cordless PCC600 with a broken Chuck stock about 5/16" open, but will not close or open running the motor back and forth, it's broken gears and Im unable to remove the inside T20 screw any ideas how to replace this broken chuck?, Cause the motor runs fine, it's a great drill and I will really like to keep it. Please let me know. Thank you! we
@FIXTechGuides5 жыл бұрын
Thanks for the question. Here's a video for replacing the chuck: kzbin.info/www/bejne/mKHCnouqaL-ia9k. We hope this helps!
@leonardorojas17816 жыл бұрын
Hi. Thank you. My 3/8 Stanley cordless drill chuck got stuck with a 6 mm bit in it. I didn't grip it too much, just normally, but it won't undo. It's stuck. Please share some ideas to free it up. Thank you!
@dorshem-tov24707 жыл бұрын
very helpfull tnx
@khalidelkhaoudi24396 жыл бұрын
Dor shem-tov chinyoul.mastar
@Mephistahpheles4 жыл бұрын
My defective chuck won't hold anything firmly....so using an allan key/hammer to remove it isn't gonna work.
@origummy_6 жыл бұрын
1:33 That's some drill porn right there
@randytetznercfi2 жыл бұрын
What about a Makita right angle drill that has a huge Implement stuck in it and you can't open the Chuck even with wrenches
@FIXTechGuides2 жыл бұрын
Time for the hammer, LOL! When this happens I've had good luck using a hammer and a punch. Clamp the stuck bit in a vise with the bottom of the drill chuck facing up. Place the punch on the chuck's body next to the jaws. Strike the punch with the hammer until the chuck's jaws slide off of the bit. This method will usually work. In the rare case that it doesn't, I will resort to cutting the chuck off of the drill with a grinder and cutoff wheel. -Mark
@rairudra80126 жыл бұрын
hi i want to change DCD996 chuck but i am not sure how to do it. thanks
@huynhquangduy37955 жыл бұрын
Hi, can you teardown Ryobi CDL1202P? I can't repair Ryobi 1202P gearbox, thanks :)
@mulletbubbles99093 жыл бұрын
So what if you cant anything in the chuck because it actually is stuck
@cassiya1008 жыл бұрын
It'sm all good but my Jacobs chuck is stuck? It will NOT allow me to open it to change bits. It just won't open.. Any tips?
@otaku_god14598 жыл бұрын
cassiya100 same problem..did ya figure it out.?
@cassiya1008 жыл бұрын
yep.. I had to use a large grip pliers, same type as used by plumbers.. grip it tight and twist, it should do the trick.
@elmerovero75284 жыл бұрын
@@cassiya100 I'll try that
@asheeraukhez96587 жыл бұрын
hello i need help, i have a Makita XPH07 and i want to know whether i can change the chuck from keyless to SNS. thanks any help very well appreciated
@FIXTechGuides7 жыл бұрын
I haven't found an SDS Chuck that is compatible for your tool.
@joaquincortada14833 жыл бұрын
Ok, what if you a drill bit stuck in there you can't get out????
@robertdrury88537 жыл бұрын
Hello , I have a Makita LXPH03 cordless drill , the problem I have is that the chuck pulls out of the gearbox with shaft intact..Is there any way to fix it?? Thanks
@FIXTechGuides7 жыл бұрын
Unfortunately the shaft is part of the 126448-9 Gear Assembly. Makita does not provide any parts for the Gear Assembly. You would have to replace the complete gear assembly.
@robertdrury88537 жыл бұрын
thanks for your help..
@Mihogan4 жыл бұрын
Thank you! Thought my drill was shot. Here I forgot last time I used it, it was raining, so the clutch rusted shut. Thanks!
@jamescram46742 жыл бұрын
But I dont have a drill to drill my drill because my drill is broken...
@david.lemyre Жыл бұрын
I put a drill bit stuck in a vise and then I used the broken drill to drill itself
@johnryder17134 жыл бұрын
You can always depend on you guys to come up with a solution
@RomboutVersluijs3 жыл бұрын
Does any one perhaps know why a chuck starts to rattle and slip when i try to loosen it. It sounds like grinded teeth. It still drills and drives. Yet manually loosening the chuck sometimes makes this rattling sound
@untrust20332 жыл бұрын
Why the door knocking effect?
@jonyhopkins17 жыл бұрын
Good vidéo thinks
@keithrosenberg54863 жыл бұрын
What if you get the screw out but the chuck won't come off?
@edawriter3 жыл бұрын
I got the retaining screw off of my Makita XPH07 but I can't get the chuck off, no matter how much I hammer it as shown.
@HM13.3 жыл бұрын
Same problem with my DDF480 stucked chuck. Have tou manage to solve your stucked chuck issue?
@edawriter3 жыл бұрын
Nope. I gave up. Fortunately the drill still works.
@SW-ot7bf3 жыл бұрын
Makita ddf481???
@bluemantom778 жыл бұрын
i need to change the chuck on my dewalt dw991 i dont want to replace it with the 3/8 it has now can i put a 1/2 chuck on it ? if not the way it is what must i do
@FIXTechGuides8 жыл бұрын
Dewalt doesn't show the 1/2" Chuck as an option. Usually the 3/8" drills have lighter duty transmissions, spindles and motors in them and they aren't able to handle the stress of the larger bits. The link for the 3/8" Chuck is as follows: www.ereplacementparts.com/keyless-chuck-jacobs-p-64641.html Keyless Chuck (Jacobs, 3/8 [330075-46] for Power Tool ... www.ereplacementparts.com Buy a Keyless Chuck (Jacobs, 3/8 [330075-46] for your Power Tool - This 3/8" capacity chuck mounts to the drill using a 1/2"-20 threaded spindle. The light-...
@bluemantom778 жыл бұрын
eReplacementParts.com i also have the dewalt dw990 DeWalt said that the housing/shell is the same only different is sticker on back with model number Lowe's speed Manufacturing info housing cover cracked and i know that is a 1/2 inch chuck on that model i just need to replace the clutch because i can grab the chuck why i hit the trigger
@FIXTechGuides8 жыл бұрын
Dewalt has 4 variations of the DW990 and another with model number DW990Q type 4 all of which show the Transmission as being no longer available and they don't offer a replacement suggestion. Just a heads up regarding Dewalt tool model numbers.... Dewalt tools sometime have different variation for the same model number. This is true for your DW990. These show Type 1, Type 2 and so on. It is very common for the parts between the different types to not be interchangeable.
@bluemantom778 жыл бұрын
eReplacementParts.com i understand i took the motor off of my dw990 and put it on my dw 991 with new carbon brushes as well as put the trigger switch that my dw990 useing same fwd and reverse switch that came on the dw991 because the fwd & reverse of my dw990 dont fit the shell of the dw991 but it's a hundred percent Improvement in performance and I can get the clutch with the spindle that can handle a 1/2 chuck on ebay new old stuck I might do that next and it would be like8 having my dw990 the way it was in 2001 when I purchased it i do own a newer lithium 12 v max but love the rock solid rocket construction of the older dewalts and other brands now they feel so cheap so my motor is of my type 4 dw990 dewalt so its a xrp model its heavy duty motor the trigger switch is from dw990 so its heavy duty k got a new clutch coming to me for dw990 with the right coller that turns up to 23 before drill icon i just need a new transmission gearbox and am back in business not to say it dont work just fine with the clutch from dw991 and transmission from the same model I'm just going to use it for diy repair projects around my house for work i use my dw995
@HelloHello-hk4sx2 жыл бұрын
What if it's welded on?
@LaurentLABRUNIE6 жыл бұрын
Does someone succeed to remove chuck on an XPH07 drill. One day I try and no way... Please nedd help !!!
@aircommuter3 жыл бұрын
Mine has a bit stuck in the chuck?
@StrixVFX3 жыл бұрын
bro that knocking was way too realistic with headphones
@suzedunmow526 жыл бұрын
My countersunk is stuck in the chuck, and the chuck is stuck, impossible to undo & release my countersunk, so I am unable to even get to the stage of checking the chuck screw inside....
@leonardorojas17816 жыл бұрын
Suze Dunmow Hey, we're you able to undo the chuck of your drill? Mine just got stuck. It's an Stanley 12v drill. Very good until now. Any ideas?
@suzedunmow526 жыл бұрын
no, I couldn't do it, but then my hands are a bit older & weaker nowadays... I took it to my local hardware shop, and the very helpful guy did it with one strong twist. It had got a bit clogged with some plastic from me drilling holes in the base of large flower pots... somehow it happened again, and they fixed it again, but he also told me you can buy a replacement chuck... so, so long as it doesn't get stuck with a drill bit in it, I will try undoing the screw like this video says, and then maybe go try and buy a replacement... Good luck with yours! let me know if you managed to sole it, if you feel like it :)
@mouradkendi15914 жыл бұрын
How to open a chuck and clean it
@The1fuzzydog8 жыл бұрын
how to remove a left hand threaded screw: use your other drill
@kristiankolev84416 жыл бұрын
The1fuzzydog If the bolt is so seized that the head gets heavily damaged (or already is so) there's really not a more merciful option for the chuck and the whole drill.
@markvietti6 жыл бұрын
if the chucked worked enough to clamp onto the big Allen wrench i wouldn't have to replace it...
@ashscott60685 жыл бұрын
File down the wrench to fit into the chuck. Chucks cost more than allen wrenches.
@Sk00pZ8 жыл бұрын
that knock boss
@KleChii3 жыл бұрын
I thought someone was legit knocking on my door
@joseojea565 Жыл бұрын
Most disagreements can be settled with a hammer! …lol
@mum2027 жыл бұрын
Dear sir help me plz how to remove chuck from HP 1640 makita drill
@FIXTechGuides7 жыл бұрын
The Makita model number HP1640 does not have a chuck screw. If you follow the instructions shown in the video it will come off. The problem with Hammer Drills, is that because of the constant hammering the chuck will be harder to remove from the spindle. Make sure that you have the selector in drill only mode and not in hammer mode
@lilyslife472 жыл бұрын
So I need another drill to fix my drill lol
@alexplorer6 жыл бұрын
I can't believe there was all this screwing/unscrewing by hand. Just pull the trigger! That's how I always adjust/tighten my chuck.
@bitTorrenter3 жыл бұрын
Niceeee
@christinewilson76177 жыл бұрын
How about if itis seized around the bit?
@FIXTechGuides7 жыл бұрын
I am still researching this for you. Will have a response soon. Thanks
@christinewilson76177 жыл бұрын
Fixed it by hitting the end of the chuck with a hammer. Yay!
@shaneruud6 жыл бұрын
I cut the outer sleeve length wise on a angle so I wouldn't cut the plastic housing with a band saw. Peeled the sleeve off put a releif cut next to a jaw and knocked the jaw out with a hammer and screwdriver. Could be done with a sawzall all the metals that were cut were very soft.
@afatninja7 жыл бұрын
yes, no good though, when you have a drill bit stuck inside
@DrJeffConklin4 жыл бұрын
See below
@lucianoippolito14436 жыл бұрын
How to remove in DCD996 dewalt ?
@FIXTechGuides6 жыл бұрын
Hello, unfortunately we don't have a chuck for a DCD996.
@veron63856 жыл бұрын
Do you know how?
@brightspark547 жыл бұрын
I wish mine wouldn't bloody remove
@edmalo79366 жыл бұрын
Hello my ryobi chuk is stuck please help me
@FIXTechGuides6 жыл бұрын
Hello Ed, some chucks take quite a few hits to remove them. Just make sure your drill is in the drill mode and is set to low speed.
@edmalo79366 жыл бұрын
Will give it a try thanks 4 answering my question will get back to you
@malomalito60486 жыл бұрын
Nice it did work
@scottlewis78932 жыл бұрын
My chuck is stuck fully opened heeelp!
@tomthompson74005 жыл бұрын
why would you beat with the side of a snap on dead blow hammer ,,, good grief ,,, and then use water pump pliers where vise grips would work so much easier ,,,, ah well , at least your cream shirt stayed clean.
@khalkhal23725 жыл бұрын
The background music is aggressive and useless. Anyway, good job
@mattmcghee77566 жыл бұрын
title is misleading its the screw that is the stuborn not the chuck thx for wasting my time