Homemade PIPE BENDER !?

[@JoelArseneaultYouTube]

I wasn't going to say anything, but with 7 million views, you have some responsibility to the people to be honest and point out that this does not work well and that it is far from idea. You are going to motivate people to purchase dies and materials to make this tool, and it will be a waste. I can see from the video that the bends are not consistent (the radius is changing) and the bends are damaging the pipe, unlike a properly built bender. This was a fail, and should have been labeled as such... or at least pointed out that this was NOT idea and the results were not great. Instead you hyped it up like it all went to plan. People. If you are going to bend different size pipe, you should be using the appropriate size die and follower. If you are going to bend more than one size of pipe with one bender, you need to have an adjustable follower or keep your follower close to the die to avoid kinking and other issues. This would be a good video IF it didn't end giving the audience the idea that you can repeat this process and be happy with the results.

[@kalemarthur4425]

I think it’s a great built even if it’s not 100% it will work only thing I would add is interchangeable wheels for bigger sizes

[@djordjejon4849]

Domaca pamet kad proradi iz radionice drago mi je kad vidim da neko radi sa apetitom vidi se da si perfekcionista nista ne prepustis slucaju.👍 Pozdrav iz Srbije

[@Ebasmebriga]

Potpuno se slazem da je veliko zadovoljstvo gledati mladog momka kako ima zelju i znanje za rad. Ali od ovog momka bolji je momak na kanalu peChoO

[@daveman5860]

I make this sort of thing but I make sure the pry bar swings up and down for leverage. Plus there should be absolutely zero wobble, jiggle, so that all your kinetic energy goes into the bend. Also I use a really Stout long pry bar lever, makes it a cinch no struggle. Especially when you have to do hundreds and thousands of bends,💥 that's my two cents. Great job by the way. The next one I'm building, bends to solid bars at once.

[@DrHenriqueVet]

Queria eu ter a metade das ferramentas que ele utilizou. Mas é inegável a habilidade do rapaz. Ficou muito bom o trabalho. Parabéns!!! Congratulations!!

[@gelsonrocha412]

Apesar de ser tão jovem, porém muito sábio e incrível a tua sabedoria além de ser super organizado. Está de parabéns você é um excelente profissional.

[@yaguswahyudy6904]

a very useful video, as long as people watch it, the more God's reward flows for you.

[@fordguy8792]

Nice build. Only concern I have is the welded center pivot. The plating on those commercial bolts makes welding them sketchy. Make the center pivot 5mm longer and pass it through the baseplate, then weld the head from the other side. That will send the bending forces through the shank of the bolt into the baseplate, instead of through the welds on the sides of the bolt head.

[@idazonunpuii4368]

You've got every tools every piece wow 👍

[@juancorral3237]

No pues... tienes un buen de herramienta. ¡ Tienes una ferreteria! Yo a luchas tengo unas pinzas ☹ . Pero exelente trabajo 😀. Me gustó lo que hiciste.

[@AlejandroGutierrez-dx7he]

Excelente forma de trabajar voy a ordenado muy ordenado muy limpio tienes muy buena herramientas todo excelente lo único que faltó fue una base de cemento en el patio para colocar la curvadora saludos desde Colombia

[@geo2cv6tron14]

The first construction of the new workshop, it is so much more rewarding to make your own tools 🛠

[@ДенисСухачев]

Ррр

[@ДенисСухачев]

П

[@dappa211]

you need thicker plate and a more solid handle. a few more bends and its going to bend or break

[@trevorbyron9448]

Straight onto business. That's what I call a workshop

[@tfagarage]

Well done, in my opinion, you just needed to make a 90-degree fold and another 180 to see how the curves will be.

[@mdrihan7356]

llllllll

[@kerenjustavino8987]

7

[@cuongnguyenduy8141]

Cho tôi hỏi ! Vì sao khi tôi uấn ống kém lại bị gẫy mà không giữ được độ tròn của ống ạ ...

[@АбдурахимАламхонов-д5ж]

@@cuongnguyenduy8141 .

[@nenad-ludoski-francuz]

Trebas ga malo preraditi,jer ovako mozes savijati cevi samo do odredjenog precnika(fi). Jedan roler si trebao napraviti da se moze štelovati pa tako da mozes savijati i deblje cevi. Inace korisna stvar. Pozz iz Srbije 👋

[@LJC5865]

Very good. Then thinking of adding a big bottle jack with corded drill instead of a lever. Wanting to build my own exhaust system. Again thanks for posting.

[@kodihull3820]

Hey man great job but I see a problem it’s flexing needs more reinforced and needs to be mounted to concrete not a wooden workbench

[@tonesdrones7395]

Where did you get the roller dies frome i cant find those any where! Help!!!

[@DRAGNET-pn5vf]

CHECK A SCRAP METAL YARD, ALWAYS CHEAP FINDS! 🇺🇲👍✌️

[@eliperli3663]

Excellent!!! 😁👍Although, you might have to heat it with a torch to make it easier.

[@officialWWM]

Is this guy working inside a hardware store? 🤔

[@carlossegurachavez7711]

good idea, the only bad thing is the axis of the main mold welded to the plate and of greater diameter, the best would be past and thicker, it is observed how it moves by the applied force.

[@miguelangelargueta9361]

Exelente maestro, no le doy un aplauso sino un millon, felicidades

[@robbylausrichiez3231]

Como de llama ese material redondo que esa para doblar los tubos??

[@chrissmichaels]

The video was quite cinematic as if someone had written the screenplay. Didn't skip a second like I do with most videos. A very interesting and informative one. Keep it up bro. GBU

[@googleyoutubechannel8554]

Step 1 - have all the key expensive components of a retail bender tool...

[@badtrippin]

i follow Leandro Torneiro, an brazilian maker doing this project and must tell, this tool is awesome!

[@SamGamyiKLC]

Fantastic!. But where to get those wheels?

[@johnnymcclurg9672]

Were you able to find any

[@SamGamyiKLC]

@@johnnymcclurg9672 in a F1 race car?? 😋

[@micky5552]

Google Rollers with U Groove

[@Z-Ack]

Looks like it would kink some thinner walled stuff though.. maybe if you took another pulley any cut it in half to use as the support part..

[@SolarRepublic]

How're Parkside plants?

[@gilfordpitso3929]

good job but i believe heating it with heating torch helps a lot also

[@philiphartley8823]

Yet another DIY'er who uses a vernier gauge as a scriber... puts me off straight away.

[@alejandroromero916]

Guess what. There are cheap ones... you cannot believe how "common" this practice has become. Yes buy a cheap caliper instead of a scriber compass.

[@bessam21]

from Algeria the first

[@oketayoo.g3907]

Excellent presentation. The Lord God bless you in Jesus mighty name

[@emilystubbs5650]

VERY well made video - I love when there isn't a ton of talking in the beginning, or at all if the footage shows it all. QUESTION ❓❓❓ If the largest pipe I'd want to bend is . 75" inches, (conduit - so steel or aluminum) you think I could get away without welding the pieces you did? Or... would you consider making one to sell??

[@Z-Ack]

Buy a conduit bender on amazon, like 40$ or so and make sure to get one for 3/4" rigid and is made from steel, not aluminum if bending something other than emt or aluminum or rigid pipe.. its like a head shaped like a J and a handle that goes on the middle of the j. You usr your foot and the floor as leverage like a shovel..

[@emilystubbs5650]

@@Z-Ack ohhh ok ok. Awesome thank You very much!!!! ❤️

[@samirkaroune7006]

Greetings, you can add a little bit of oil to make it easier to slide

[@CavRic]

With this tool it is possible to bend stainless steel pipes with a diameter of 20 mm.???

[@carpadani6766]

welding on a wooden table is a bad idea bro!!! great bender

[@fonwoolridge]

Awesome! Im new to metal work... and would love a pipe bender... Gonna have to wait a whil longer before I can do anything like that!

[@agerworks7034]

Where did you get the wheels?

[@chriskazaglis]

MAX! Everytime I saw MAX! I said MAX!

[@WELDEROFMASTER]

Good videos tutorial next time boss 👍👍👍

[@staryi5119]

The large roller should not be spinning, it should be stationary.

[@christiantaylor6867]

Where can someone by the round dye pieces at!!!???

[@roberttarr1875]

I think ,it was a little bit to light .😁 But working good .👍

[@slavkoblazevic7484]

Koju si školu završio

[@Николай-с4т7г]

Слабая конструкция, трубы еле гнёт, должен быть зазор между роликами 10 мм, без забзора поэтому так тяжело гнуть

[@Varwelder]

Dobra ideja,pravio sam sebi nesto slicno,ide to mnogo lakse uz grejanje

[@redouanofficiel]

kzbin.info/door/6ioKYOovUi9r8h4orOQ8pQ

[@rolandoca3570]

alguien q m proporcione el precio y en dónde la pueda conseguir vivo en Chalco estado de México x favor

[@joseivaltolaurentino2812]

Boa tarde! Gostaria de ter muitas ferramentas assim... parabéns pra você!

[@dzozepe]

hello where did u get those bender dies/wheels please?

[@521farmer]

Wow awesome build thks for shari ya dont need to be rocket scientist to do this great idea going to build oe great for building gocarts and Old School Choppers so from Canada 🇨🇦 SK later 😊ya got this 👍

[@kirbylee57]

How do you make the dies?

[@JorgeMartinez-j3c]

Amigo buen trabajo gracias por subirlo 1)la chapa de 6 mm es fina de 1/2 para arriba 2)los tornillos no sirven ejes de 40mm para arriba 3) perfora la chapa de 1/2 la que pongas de base los clavas y solas por debajo Te mando un abrazo muy buena intención mejora algunas cosas el concepto lo tenes 🇺🇾

[@joe226825]

It looks like it's made for 1 size of Pipe only.The rear anchoring back U shaped plate should have been made to accomodate several different sizes. Otherwise I like how it has degree markings capabilities.

[@innovationtime20]

Nice👍

[@xinkaelusher663]

The most important part are the pulleys, where did you get them?

[@youthuber13]

Good idea! Thanks for sharing. Keep safe. Watching here in Canada

[@MrMcbuck48]

Nice, where do I get the wheels ?

[@micky5552]

Roller with U Groove

[@samcarrs]

It’s practically a tubing cutter. Your tubing is marred up now. Thanks anyways

[@lawrencecarver3299]

What happen to measure twice cut once?

[@robertbondoc852]

You should install this in a separate solid metal stand.

[@rustymarrow]

dads gonna be pissed ha ha bending his pipes up lol jp

[@mihajlogolubovic2328]

Tooo samo tako nastavi imaš moju veliku podršku

[@drsemomaa]

can you call it a home made??!!!

[@joacirjoaobiaggio9968]

O garoto tem um aparato de Dar inveja

[@iman80skid91]

Your small rolling wheel is too close to the form wheel that's why your having to put so much pressure on the bar

[@glenbegin9152]

where did the round discs / pullys come from?

[@user-ki4llalm6kr]

They come from either working or having connections in the steel manufacturing industry.

[@1953fords]

I’d love to make one. Where did you get the die rollers?

[@ivanvukic2595]

Tebi nikada nemoze biti dosadno,radis to sto volis a opt se zabavis,a i napravis nesto korisno.

[@jayantithapa1437]

0

[@allsongcoverbysunil285]

🙏Sir Excellent your job keep your blessing us 🙏 i from mumbai india

[@josuaplatt1830]

Easy when you got All the tools 😂

[@keithwaterman9404]

Run of the mill build. Anyone with scrap pile and welder can build.. Real trick is where to get the round dies.

[@jakubajanovic4564]

Pozdrav Davide.Kako se zovu ovi kolutovi sto savijaju cjev

[@TheDonil]

nice but does it work properly on hollow pipe??. I mean clean bend??

[@andrewmccutcheon4650]

Where can I get the pulleys?

[@bengkellaspanga1965]

Apotek

[@ekulda]

Good job 👍 what if we want to increase the diameter of the pipe?

[@DRAGNET-pn5vf]

LOOKS AND WORKS GREAT, THANKS FOR SHARING. CAN YOU MAKE A METAL ROLLER TO ROLL FLAT METAL PIECES? 🇺🇲🌞👍✌️

[@ramsaroj2960]

9oooo

[@asvianvahrul2452]

Me watching this : he is a profesional 👍

[@maxyt8058]

ALI JE LIDL PRAKSIDE PLAZMA DOBAR PRODUKT ALI GA VI PRIPOROČATE PROSIM odgovor i stvarno lepo delavnico imaš pozdrave iz Slovenie

[@neolord9877]

Zanimljiv video, odlična savijačica. S istom možeš si praviti vilice od rebrastog (šipki) željeza za armirani beton kod nadvoja, zidova, temelja i slično. Bravo Doctor. Veliki pozdrav!

[@nurgazykydyrbaev8002]

Пп

[@iwarantiwa1346]

Thanks 👍 Alhamdulillah

[@epefaniocamacho5006]

Nice, what kind of welding you used, that you are not using welding rod

[@aleksarocenovic5438]

kad ce vise video o bmw-u

[@first25q43]

I made something like that for .500 tubing. Many years ago. I use a bearing on the small wheel. I Mande the wheels. I used a .500 wide tool bit. With the radius on it. Great job. Keep up your great work.

[@peakpointchannel]

GOOD IDEA SO MUCH

[@germanisierungstoppenvolks2602]

Hello Dr. Ds. Do you can show us next time to produce a Homade Garden Wagon from Wood? Big up from Germany !

[@crisbacnis4464]

What is the name of that pulley sir..how can i buy that....thank you

[@qigocuttingmachine-xingowe2855]

If you want a pipe bender, you can contact me or watch my video.

[@juliovera3826]

Muy bueno y muchas gracias por este video maestro.

[@candysuperbanda4243]

11:38

[@candysuperbanda4243]

11:38

[@leo_wwwbmw_leo5958]

Day vise pricaj,ko se slaze neka stavi lajk,Dosadno je kad ne pricas!😨

[@gayatriwwagh8391]

Hi doctor i like this one's exterior design

[@fadelazavira5634]

Lealohi lensa amboru

[@SHADOWARCHILI]

most needed parts are bending Die .. so without that its impossible to do nice bend without defects. show how and where did you get that. cheap...

[@nickgc1234]

where do you get the pulleys from?

[@panolatile3968]

Thats exactly what I need to know I looking everywhere I can’t find it

[@cadinhoeumesmo2993]

@@panolatile3968 Nós temos muito dessas polias aqui no Brasil. We have a lot of these pulley here in Brazil. And they are not even very expensive. Do you really need one

[@panolatile3968]

@@cadinhoeumesmo2993 give me a model number I’ll try to find it online thanks

[@johnd7068]

Отличная работа! Спасибо за видео!

[@philipphilos4886]

not good

[@saijuakshaya1983]

Bro I think you crazy and love with tools

[@keithb4007]

nope....just no. not a proper bender.

[@officialWWM]

Is the pipe bent? Actually, yes, it IS a proper pipe bender!

[@ИванДубровский-ж6к]

Да уж. Конца этому не будет никогда. Беда, наверное, в том, что кто-то желает стать умнее, а кого-то устраивает всё как есть. Тёмный, затюканный электорат - это сила и опора. Для них и "заведения" новые строят по всей стране. Вместо школ😂

[@TedThetford]

Smart and effective!

[@bablusarkar7304]

O

[@emigrant74808]

Why you used just cheap plasma cutter if much better would be to use CNC workstation? (Ironic) plasma cutter is not necessary at all but sb is paying you so you are doing things you can't show how they are working lol

[@adamek.K.91]

Hi. I made a bender like you and it flattens my pipe why is this happening? sometimes it breaks at the bend. answer

[@jeffreycanonero6745]

This video is just an good idea for bending pipe and its not designed for all sizes. In your case, wheel Pulley (slot size) was not the fit size for your pipe. It must be fitted in the slot order to hold the whole side of the pipe so it would not flatten.

[@agona-piesie6604]

This is fantastic, I wish to have a work shop like this with all these machinery, thanks for your good education. Watching from GH,

[@chatchaikatiyakun2528]

ฟฃฃวฃ