Homemade SNOW PLOW for MOTOCULTIVATOR

[@danmoreton1788]

Nice to see a young man welding and fabricating!

[@MrDKDIY]

Bravoo.majstore svaka cast

[@billstmaxx]

Great build.. Few things i saw.. Your mount braket should have a cross support in the triangle . you need a 220V welder but as this is a walk behind it should be good.. Plasma cutters are awesome as well.. also a strip of steel in front of your rubber cutting edge would strengthen as well... excellent build though

[@AYMANRAJAB230]

انت انسان مبدع .. لا بد اختراعاتك تتحول الى مشاريع .. وتأخذ نسبة ارباح منها تحياتي متابع عربي

[@genewright2732]

Damn. I'm tired just watching him make that. Genius at work!

[@richardm1631]

Cool little snow plow that was good idea

[@jeffrutan8521]

Damn dude..... That looks like more work than just shoveling

[@toddkratzer7953]

Exactly, well said.

[@Kojic966]

To se čekalo.. Čitaš mi misli legendo ❤

[@DShomemade]

hehehe

[@songofthepassaic1521]

Excellent build! Just one bit of advice. If you were to put more of a curve on the blade it would get under the snow and roll it off to the side easier.

[@CrusaderSports250]

Somewhat easyer than the shovel, a good job jobbed.

[@pondacres]

Young fella, that's some impressive fabrication skills, and a well done vid.

[@miroslavvfilipovicc9162]

Odlicna stvar samo tako nastavi poz brate moj 👍👍👍🔥

[@electroworld8733]

Super video and music. Thanks

[@DoitselfInfo]

Your idea is very good! Maybe you can improve your device, for example, you can place two bags of sand on both sides of the cultivator to make it heavier, then the wheels of the cultivator will not slip. Thank you for this great idea!

[@НурипаОшанова-в1ш]

'

[@alward9901]

Good one and no snow on a windy day blowing all over you when you have to go against the wind 💨⚒🛠👍

[@rikigeorgievski]

Odlicno samo produzi tako, pozdrav iz Makedonije ;)

[@DShomemade]

poz iz Hrv

[@goranstojkovic5838]

MIO standard Osjek, HONDA. Odlicni motokultivatori, a ideja ti super i ne kosta puno, jer ima i kupiti otiginal... da nije hladno odmah bi iskopirao ideju jer imam isti. Bravo. Pozdrav iz Srbije!

[@DShomemade]

ovo je originalni hondin motokultivator ali imao sam i mio standart f430 tak nest :D Taj je vukoooo ko lud :D hehehe poz iz Hrvatske ;)

[@goranstojkovic5838]

620y 😀 Jel MIO ne proizvodi vise motokultivatore?

[@dededenver9560]

This guy paid attention in shop class! Nice job.

[@МихайловИгорь-ч1ц]

Уже третий сезон убираю снег с помощью отвала и снегоуборщика. 1. Отвал у меня тоже ворочается вправо, влево , но на один бок убирать гемор(очень медленно, 48 раз проход по одному месту).2- Сделал отвал похожий на ковш: увеличил вдвое высоту(такой же как на видео стал) и приварил боковины. Реально быстро и эффективно грести снег только прямо( но сразу скажу, что усилий приходится прилагать совсем не мало, сам мотоблок не поедет, буксует , не знаю как на гусиницах). Сгребаешь в большие кучи, а потом либо меняешь отвал на насадку-снегоуборщик, если снег еще не слежался (около половины поможет перекидать, потом все равно лопата), либо сразу лопату в зубы и вперед - пахать. 3. Одна насадка-снегоуборщик тоже не вариант( желателен полный штиль, снег 20 см, не сырой) . Но лучший и верный друг все равно ЛОПАТА. При любых раскладах работу заканчиваешь с ее помощью. Зато тренировочка еще та! И главное: вспотел, спина начала подмерзать, иди и переоденься в сухое. Тогда труд на пользу.

[@sonyhk3824]

It's working perfect, well done

[@neusac4590]

Nice job, as long as you have the right equipment. 👍👍👍👍

[@callhow]

Nice work ! Watch your neighbors for when they put gas grills out for garbage - those stainless steel lids are Great for making snow plows for; tillers, and even in front of snow blowers for light snow & slush. (make sure your plow will clear augers - if used accidentally. 😉

[@ravenfeather7087]

A nice build. I wish I could weld like that and may soon learn how to. Your device reminded me of a plow my father built many years ago and attached to a Standard Twin tractor. If you're interested there are several videos of Standard Twins on KZbin. it's a smaller garden tractor with large wheels on the front and on my dad's version smaller wheels on the back. I've used it for many years to plow snow. However, even though it is much heavier than your tiller it was still difficult to use with heavy or deep snow. Having the blade angled like that pushes the machine to the side quite easily. And with the blade perpendicular to the axis of travel simply not enough traction. Even with chains on the large tires, probably 40 inch tall and weighing in the neighborhood of 150-200 lbs each ( I can barely stand one up vertically from a laying on the ground position. My dad added lead weights to each tire.) and the added weight of the tractor itself it does not have the ability to push a lot of wet heavy or deep snow. Even though there is probably in the neighborhood of, I suspect, at least 500 lbs distributed over the two front tires that drive it. It works though for lighter snowfalls! Well, worked, the motor finally gave up. I'm guessing that you have found that it's not very effective for anything other than light to moderate dry fluffy snow plowing. You should have contacted me before you built it! I could have cautioned you. But then you wouldn't have had the fun of building and testing it. Again, nice build.

[@gordbaker896]

Well Done. A shorter height blade and more weight over tires might help. I made a similar pusher that attaches to the front of the rear half of a snowblower.

[@mohamedkhorchani7269]

You are the best doctor👍♥️

[@277patryk]

Jak widać taki motorek można do różnych robót wykorzystać 👍

[@nathanduckeorth806]

Small set of tire chains an you got it kid! Nice!

[@zoricalevic9928]

Laonoa😘😘

[@kikodriver2255]

Svaka ćast. Imamo isti hoby

[@DShomemade]

;)

[@markbooe205]

Good Design!! Excellent Job.

[@vausa1000]

A real professional indeed. Wish I could buy one.

[@adohd1066]

Odlicna,vido pozz sam nastavi brate

[@Iowaracefan]

Good idea, adding weight to the wheels would help.

[@vitopejakovic3848]

Predobra ideja!😀😀

[@vlastabrnjevarac873]

Svaka čast majstore. Super stvar. Možda samo ne može na brdovitom terenu.👍👍👍 Samo još da napraviš lance za kultivator i ekstra.

[@DShomemade]

Daa obavezno neke lance i togove trebam stavit ;)

[@maxtoyotov3493]

Interesting video, avtor 💪 💪 💪 💪 thank you All power

[@boglud232]

Nice work👍☺

[@basilbasileus7211]

Idei geniale! Bravo!👍👍👍

[@MrKukec]

Man you sometining else♥️ Pozdrav from Chicago

[@tcmits3699]

A rear v blade would be great, no fishtailing, plus if your handles flipped over and you reversed, now your v blade becomes a v scoop. 😊 good luck 🤞

[@opgdavorpahic5699]

Sve odlično, jedino je kultivator pre lagani

[@Andrei-mi1fr]

За идею 👍 Ну много минусов, всё таки лучше ручной снегоуборочной машины ни чего пока нет.

[@meryl1556]

Good creativity ! Congratulations bro !

[@Patriottoo2]

He made something for little money that proves the concept. He used various tools, while making the plow... a reward unto itself. What did you make, today?

[@theknifemaker123]

Very cool way to have fun in your shop and way more fun than shoveling snow lol thanks for another great vid! :)

[@NIstrumone]

Once again...you have done it again...another great idea..great build...great project....very creative...keep those videos coming !

[@crazyfinisher5743]

Svaka čast bratee

[@craftman5632]

Might uses this idea on my snowblower, when the snow is slushy and it clogs up the snowblower.. use the power of the six-speed snowblower to push the heavy slushy snow off the driveway, convert it into a snow plow. Maybe just bolt on a metal snow shovel blade. ❄️🤔

[@bryandinardi2519]

Cool idea, but a snowblower would work a lot better 🤷‍♀️

[@ИванРудень]

20000+. Лопата чистит и это главное.

[@jorgekazachek6514]

nice work mate smart idea!!

[@jamesexploringonline872]

Great work Dr, also luv your bike, ♥♡♥

[@stevesmith6058]

That was a beautiful job that you made that is really awesome

[@AliAhmadi-hq9pj]

I dnt know what say. You are amazing. Wow I ❤️ your video 👍

[@jamesnm21]

Put it on a riding mower or atv. I hate snowblowers almost as much as snow shovels. They're almost as much work..

[@fm812]

imas ti potencijal svaka cast majstor

[@teddysgunshop2318]

Snowblower is faster and does a cleaner job nice work though

[@joeymohlis3010]

but why do that? this is more fun!

[@6.7heaven92]

Snowblower is more money though unless you get the craigslist special😂

[@hudsonhawk0016]

Hmm, hardening the mold board behind the cutting edge with weld. That's pretty slick. Nice work!

[@robinbenge1067]

First time seeing me and you're very talented yes you can buy it for cheever lady but doing it yourself that's a challenge and apparently you like a good challenge keep up the good work

[@diy8295]

Svaka cast majstore :D

[@DShomemade]

:D

[@adamr8628]

Nice. But all that work! I've bought several plows like that for $40, commercially made, more heavy duty.

[@matteckert6676]

Creativity is nice. Doesn't seem to work too well though. Possibly adding rear weights 🤷‍♂️

[@kincsesgeza537]

PA STA RECI ? BRAVO !

[@johnjacobjinglehimerschmid3555]

Cool idea. 1. Thinking ... hmmmmm wonder if I could do that with my tiller. 2. Rear Tiller ... I could just remove the tines in the winter. 3. Would have to find some scrap steel and learn to weld. 4. Wonder could the drive wheels be slowed down? Or could I find tire chains for grip hmmmmm. Wondering .... Why something like this doesn't exist today. You buy a rototiller and it's used, what at most, twice a hear .. To prep the garden and to end the garden ..... It should have a mower attachment / and this a snow pushing attachment or even blower.

[@SCORPIONS404]

Респект!!!👍👍👍

[@andrewcorrell7514]

Nice work young man!!

[@mattlindgren2886]

Nice job young man.

[@farisdelic5493]

Slijedeče Vodena pumpa od trimera☺

[@DShomemade]

agahahaha

[@ivojukic7546]

Jos si napravis gusjenica i ima da ide ko metak 😁😁 poz

[@DShomemade]

heheh da daa

[@struja988]

Treba jos malo zaobliti. U svakom slučaju bravo

[@DShomemade]

😊

[@darijodragankovacevic5786]

Ja reko ti neki stranac svaka cast

[@DShomemade]

hahaha hvala punoo

[@JDCTTR]

Looks like a fine machine, maybe add some weight to it and it would be a beast , nice build!

[@harper-igromanDS]

Молодец. Требуются небольшие доработки, но неплохо. Со сваркой потренируйся.

[@abdulrahaman9008]

Very good 😚

[@Batzajla_99]

Bolje bi bilo raditi ovo na imt 539. Svaka ti čast

[@DShomemade]

Mozda budee :D

[@myrthjt]

Works great for that 1/2" of snow you get twice a year I bet. Sorry, not trying to be mean, this is very creative. It'd be much better on something a little more substantial though like an ATV with snow tires or chains. Cheers from the north east.

[@dandeangeli9860]

I liked your innovation

[@tipoux1992]

Should have use the shovel it would have take les time

[@victa826]

another great build mate well done :) I will have to do one meself :)

[@josephmcnulty6922]

Wow all that in 15 minutes, lol. Great job

[@codysnyder8106]

If its a wet heavy snow like that, that thing is mainly useless without any real weight added to the machine

[@АйбекИсабаев-л4р]

Ну ты даеш слов нет братан дай БОГ тибе здаровия

[@LincolnSP150]

Nice project.

[@markomarkelic5720]

Pozdrav iz Bribira!!!

[@DShomemade]

Poz iz Virovitice

[@brandonmcconnell8132]

Do snow chains and make wheel weights

[@bekanstosic9158]

Svaka cast

[@klouzo8471]

From Greece. Very good

[@webhomemadeprojects1173]

It's not lazy it's thinking out of box

[@augustus22maximus]

Buen trabajo DS. Saludos desde Santander.

[@ryanbrooks3443]

That's nice it looks like it works pretty damn good!!

[@guyhermanson3002]

Come on dude. A modified snowblower would work better. I've modified mine to deal with slush and it's pretty easy. That guy went through all kinds of welding and building that ended up creating a machine that you'd have to store and maintain plus it took him quite a while just to clear a small amount.

[@garrykrause2375]

THAT IS FRIGGINNN COOL....

[@user-hy1xj3sl2b]

Ti si kraljina ceg se ti nes dosjetit

[@DShomemade]

:D

[@evanmcbride1400]

You should get a set of tracks off of a tracked snow blower for it.it would hace way more gripand look really cool

[@tractorboy31]

Atleast wieghts would help with traction

[@toddjacobs5660]

I give eem credit, he tried making somthing basically out of nothing 👍

[@webhomemadeprojects1173]

Funny thing I made 1 of them about 5 years ago. Neighbor I should put a patient on it. But told him troy bilt already made it. Nice job on urs

[@kilekile778]

Imam jedan savjet za tebe pošto se baviš sa metalom otiđi ma tečaj za tokara i zavarivača pa si kupi neki manji tokarski stroj i odlican video poz iz Jastrebarskog Čeglje: )❤💪

[@DShomemade]

Planiram daa :D

[@MG-br8ws]

Дал бог человеку время и желание

[@billychaseracing2078]

Nice job - make a big enough mess with the gas ? 😂😂😂

[@danielmariusdrenea3786]

Frumos

[@kotaluk1378]

William Hutton she's she's

tuyết rơi đẹp quá ♥️👍

[@webhomemadeprojects1173]

Made 1 about 5years ago. Fun little toy

[@guyhermanson3002]

Just modify your snowblower instead. That machine he made is a waste of time.

[@ASCarvings]

Good work.