Homemade WASTE OIL STOVE for Workshop !?

[@bentheguru4986]

Not buring clean. Air into combustion pan, setup for rotation and use the incoming airflow to cool the pan outer edges, keep heat in the centre/bottom of pan. Oil feed best dropped from height into the pan away from flame as it will likely burn oil in feed tube and carbonise blocking it. Final advice for anyone building these, all combustian gasses need to be exhausted outside. Waste engine oil contains a lot of nasties to humans and burning it indoors releases these back into the air. Example: We used to have a commercial unit buring our waste aircraft engine oil, I remember all the yellow deposites that would form around the hot air vents until I relaised what they were. The very same yellow deposits I would have to wash off the underside of the engine cowles near exhuast or blast off spark plugs. It was Lead and we in the workshop were breathing that Lead from the oil.

[@cheezeball6109]

One recomendation i think would be great is to add a inline fan that would suck ambient air from outside instead of the air in the heated space....

[@paulfrost8952]

Why is it better to suck ambient air from outside instead of the ambient air from inside?

[@connormarsh2535]

The intake air is burned and expelled. You dont want to pull in your warm air from inside and push it outside. Use outside air supply to fuel/oxygen for your heat.

[@gattonpc]

Skip to 7:55 for the actual building start...untill then is a tablet marketing.

[@dougbas3980]

You are the best! So great to watch you work! I am a poor welder and really appreciate your skills. Just found your channel and subscribed immediately. You are an inspiration.

[@UNITED_STATES_OF_AMERICAU.S.A]

I heard you have oil

[@playedbyear998]

knock knock

[@johnmarsden7687]

He needs democracy

[@edo12310]

We can build a d355a faster than you can send people Dare !

[@RandomRobloxuser-mx6xi]

I burned it all sorry 😢

[@royroyson2655]

🤣🤣

[@robertmailhos8159]

Nice looking set of home made vehicle ramps nice to see you making a heater for your shop doctor d.s

[@BonesyTucson]

Using the zip ties as spacers was clever - thanks for the tip!

[@brianbeck3894]

Everyone should have one like this. no oil problems and the air would be clean. I live in a house with 10 rooms so I make one for each room

[@stefanandjelkovic5350]

Zagadjenje 100%. Ja sam napravio za moju garazu malo drugaciji sistem ujutru sam je ubacio i u 12 sati sam je izbacio. Drva su zakon

[@1979gmcummmins]

I'm going to build one but add more of a down ward slope to the oil feed line to keep from build up and then feed the oil line through the blower tube as to help pull the oil from the tip of the oil feed cause they can build up with soot in a short time. Good build though

[@МаксимКулемин-р1б]

Масло не успевает нагреваться, как итог плохое сгорание, трубу нужно сверху внутри камеры сгорания проводить прогретое масло будет давать больше тепла и лучше сгорать, да и кстати закрывать такой котёл нужно герметично чтобы пары сгоревшего масла не нападали в помещение, для того и ставиться вентилятор принудительной тяги😂

[@drzejan_nudrik8393]

If you want the use of the stove to be better, add a water drip with which you will feed small drops of water into the oil feeder during combustion. You'll thank you when you don't have to clean such a stove from dirt :)

[@stevangubik6668]

Odlicna pec na preradjeno ulje👌Dao si mi super ideju,da i ja napravim tako nesto za radionicu👍Veliki pozz za tebe,Doctore👋

[@hartleyhubbard3827]

"...the pipes will serve as legs for..." well, we saw that coming! Sorry, I had to move on - too much time spent on the tablet commercial. Greg [garden grove, CA usa]

[@sabby05]

a small sight glass on the side would be helpful to know oil level. over all nice build

[@BuzbyWuzby]

I would add a support between the floor and the two horizontal pipes (air & oil) but apart from that, excellent! PS: It is now illegal to burn waste oil here in the UK, partly for the 'environmental issues' but mostly because the government can't tax it! 🤣

[@Jamie_c74]

Never bothered me lol

[@raymondpomfret4214]

Its already been taxed till the hilt

[@nutmeg9005]

Only illegal if you get caught friend.

[@davidwright1653]

Because as we all know the more tax revenue the government gets, the more likely the environment will be saved. NOT!!!

[@Florin76]

The oil pipe that feed the burner must have 1° slope and I suggest you put the faucet as much as possible at the bottom of the oil tank so you can burn it all. You need also a purge valve at the oil tank bottom so you can clean oil residues that deposit at the bottom. You can cut the upper lid of the burner and mason some thermal bricks inside to store more heat. Well, you can improve a lot :)

[@TheNinja691]

Have you got a video of your build?

[@Florin76]

@@TheNinja691 I didn't think to burn wasted oil until seeing this video, having a working model on which you can improve is great!

[@bencrosbie]

That's a very long ad for a tablet

[@grzegorzj.3329]

I haven't started watching it yet and I already like it 😅

[@CurtisEgan-m7s]

Best oil stove design....but you should use external air for combustion....Easy modify...thanks for the video

[@Ryantoews-xl2mf]

very nice for the winter!

[@vladim473]

Привет!🤝интересно получилось,лайк!такого вида печи я делал на дизельном топливе.теперь нужно в нее сварить теплообменник и сделать водяное отопление в мастерской.

[@meytv5691]

не повторяйте глупого доктора.

[@vladim473]

@@meytv5691 ну может сейчас время конечно другое,а в 90х,начале 2000х такие печи очень даже были в ходу ,их и без принудительного поддува делали,правда розжигать дольше,пока не начнет воздух засасывать.

[@vladim473]

@@meytv5691 конечно такая сейчас мне лично не нужна,газ,либо электро котлы сейчас в ходу

[@boosted_2j]

Wow. Look at that. A tablet woth features that every other tablet has. Wooow ooooo weeee.

[@metaframe2k]

When it flares up, you can add a little water along with the oil, the effect will be like that of a jet engine. The main thing is that the stove does not melt.

[@Duckys_world__]

Awsome video I have built a few oil burners and they put off just as much heat as my wood stove and if you a car guy easy way to get rid of used oil

[@marcoroa8223]

Emite contaminación por humo.?

[@dalespringerwilson4233]

Doesn't burn clean until it's up to temp, made several of them over the years. Smells like ass until you get it up to a good combustion temperature, and that stock pot won't last long !

[@saidmeku707]

how about if you replace the stock pot with something like well designed clay pot used for cooking will it able to withstand the usage for long?

[@mrsunyofficial]

Awesome work and inventions

[@percival23]

I would love to see how more efficient a waste oil stove would be if it was attached to a sand battery. At least 100 lbs of sand stored in a metal enclosure attached to a sidewall of the stove. After 4 or so hours, that sand battery should be close to 400 degrees and last for hours after the stove is out. It could cut the oil use in half. But I would to see a real world test of this.

[@alimasters4473]

Мне кажется что подача масла и воздуха должны вместе регулироваться. Подойдет перистальтический насос с редукторным мотором. А регулировать напряжение одновременно на воздушную турбину и насос для масла. 😅

[@MygpbluKaa]

В более менее герметичном помещении, воздуходувка создает пониженное давление воздуха в помещении и повышение внутри камеры сгорания. При негерметичной камере сгорания это создаст круговорот помещение - воздуходувка - камера сгорания - помещение, постепенно наполнив воздух продуктами горения и выжжет кислород чем убьет людей в помещении. При герметичной камере сгорания это вызовет быстрый выброс теплового воздуха в дымоход (он не успеет отдать тепло) и засос холодного воздуха в помещения сквозь щели в стенах/окнах/полу/потолке, что даст низкий КПД обогрева.

[@janisvidzs7149]

Nice! Recommendation make shield where oil flow in pipe, to prevent water from entering in oil.

[@stephenjose1472]

need to put a brake rotor (disc) above burner to extract more heat , its all going out the chimney

[@berykent4598]

Podrska za bracu hrvate. Pozdrav iz Crne Gore.

[@DazFab_Metalworks]

Nice work,i need to build one,ive been saving up waste oil haha

[@BerfuZekiye]

tomorrow's matches any insider tips from you guys would be gold right now

[@s.b2240]

Well as i have ordinary sense, rather than make hole iinfront side u may use think glass it makes more atteacting/ seal packed and also avoid the burning fuel smell

[@arthurcutaiar9994]

Stove video, not a commercial for a tablet

[@SSingh-nr8qz]

Its how people pay for the video production.

[@old-trucks-nd-Coffee]

Very very neat! Keep up the good work.

[@ep2560]

in germany not allowed in private homes . And for good reasons . Look at the color of the flame . Not hot enough for a clean and effectiv burning .

[@alexbiss9544]

you are not supposed to put it in your house it contains chemicals it is a workshop stove.

[@georgianbroadcaster4700]

Who cares

[@gazunkafonegazunkafone3492]

Germans burn lignite ffs, literally the worst form of fuel possible for emissions! Also banned i the rest of europe…but you guys ignore that!😂

[@ГригорийКусков-е2х]

Вентель подачи надо было ниже приварить масло неполностью попадёт в горелку 😊👍

[@jenyjek5055]

would be a great idea to implement some kind of water line in the otherwise unused top part of the fire chamber - to squeeze some more efficienty out of it. Great idea tho. much appreciation 👍

[@hardpeak2584]

Браво момче! Сјајно одрађено!

[@donalfinn4205]

Well done!👏🇨🇮🇵🇸

[@MetalStrength-]

Very nice job, keep going ❤

[@nemanjadjordjevic2562]

Druze svaka cast za ideju samo pazi da ne updnes u problem sa zakonom👍👍👍

[@Алекс-ц5ж]

Представим такую ситуацию: отопитель работает, вы отошли на 10 минут из гаража. В это время отключилось электричество. Наддув прекратился, а масло продолжает гореть. Кастрюля наполняется горящим маслом, потом оно горящее вытекает на пол и в гараже становится уже не тепло, а слишком жарко.

[@onegreenev]

What is the grease and fiber you used to seal the joints of the pipes?

[@tanonedekov1138]

I dont know about your laws, but in most places of the world they will give you a insane fine for this stove. Burning waste oil a lot of times is a very poluting process. Some years ago i built a oil heater but i had tons of problems and judging only by the looks of your i doubt it will work,first you have a huge burning camera(the pot)which will melt when it goes to temperature, but this will never happen because this blower is far too small for the camera.I used old diesel fuel injectors to spray the oil like a mist and the it was burning 100% but i still got thick smoke

[@pewpeww556]

Smoke is a by product of incomplete combustion

[@mambatta]

Build us one please all these numpties commenting on here with there negativities is killing me well done doc

[@shanemorgan12345]

Very nice. The only problem I could see is the air pipe not being sealed at the bottom. If the oil burn pot gets a hole or a leak it’ll burn out the bottom onto the floor.

[@hamidsanavifiroozi5274]

well done very practical

[@karpiuhp]

just add a couple of 1" or 1 1/4" pipes at the top and connect them together. plus a circulation pump and 2 radiators and substantial heat.

[@tobycanales1062]

mine runs about 900 degs. had to put bricks between it and the wall

[@danieldaniel-qr1my]

amazing the first video witout stupid voices and straight to the point !!! love it

[@geo2cv6tron14]

Really really interesting and really really cool 🤩👍

[@bimerev]

odlična peć . Imam orginalnu na staro ulje i super je to što sve sagorijeva. Jedino ti dozator na tu pipu nije baš nešto.. Moja ima nekakav rotirajući mehanizam koji gura to ulje i promjenom broja okretaja se regulira tok .. To može grijat tako jako da pocrveni. Stavi još neki ventilator po tome da puše . Bolje će grijat . Samo ne prejak da ne smeta snimanju. JA ne mogu snimat kad moja radi . I da , stavi još jednu tavicu na čemu će gorjet koju ćeš moći lako izvadit van zbog čišćenja .

[@DShomemade]

Da, Hvala ti 😁 Pipa mi je bila najjeftinija, a da je najlakše rukovanje i doziranje 😅 Da budem još jedan ventilator stavio...😉

[@bimerev]

Probaj onaj dozator za infuziju uzet, koji regulira kapanje infuzije. Mada najvjerojatnije neće raditi kako treba jer je ulje gusto. Al da bi kojim slučajem radilo bilo bi odlično rješenje

[@Jigsofficial16]

Wow that's awesome 💯

[@MarjanZuza]

Diko..odlicno..my croatian ❤️💙🔥🔥🔥🔥🔥🔥🔥🔥🔥🔥🇭🇷🇭🇷🇭🇷🇭🇷🇭🇷

[@edg1703]

great job!! where did you get the blower?

[@TheSiLq]

My only concern is that cooking pot, the metal is too thin, will burn through eventually

[@dimitrisbek6109]

very nice work.. but i would try to upgrate with closing the combustion chamber and create 4 exhaust pipes heating the inside walls

[@luisalbertom.r6378]

Eres mi ídolo !!!❤❤

[@enduroexcavator]

Odlična, korisna ideja. Vrlo dobar edit 👌💥👊 Pozz iz OS 😊

[@DShomemade]

❤️

[@joshuatremper5026]

An the good thing is, oil burns for a long time, so good for overnight burns.

[@christophe-r5n]

Pas mal ! 👏 Pare compte...si il n'y a pas de courant de 220/24/12...Volts, pour alimentation turbine 🤔??? ...ont fait comment...🤔??? Nous sommes pas complètement autonome 🤔 Triangle pyrotechnique = combustible + air + étincelle = 🔥

[@mihovilmajcen2833]

Dali bi to moglo funkcionirat da se slozi na drva...mislim da li bi grijalo garazu 5x4

[@nawafalkhader6542]

You are a struggling man and appreciate your beautiful work, and I loved that, and I'm just like you, I have great ideas, and I subscribed to the channel again, and I'm from Syria, and I love that work. Do you use car burnt oil?

[@DShomemade]

Thank you very much, that is the oil from the car.

[@MarceloDurán-d6k]

Muy buena la idea pero se paso para ahcer publicidad que no venia al caso, de hacer la estufa. Si haces publicidad que sea un poco mas disimulada

[@samuelfellows6923]

😠 ~ had to skip ⏭

[@tommyx8925]

Jetzt noch eine Wasserspirale mit eingebaut und schon hat man Warmwasser.

[@LowOctaneMotorsports]

Do you have a link for the intake air blower with controller?

[@rynasitrakarakotondrabehar787]

Were did you buy the fan?

[@DjukaWZMechanicGamingComedy]

Postavio sam klip moje peci na preradjeno ulje za centralno grejanje, napljuvali me kao zagadjivaca, kao u evropi to nemoze, evo vidis da moze 😂😂😂 Pozdrav iz Srbije.

[@DShomemade]

😂Pozz

[@wrwarnerhall]

Good work, what fan did you use?

[@DShomemade]

80W Aliexpress 😅

[@PP.EKOTECH]

Dobra robota ! :) Good job !!! :)

[@ragibtufek]

Kao jedan od najvećih fanova javljam se za udomljavanje tableta ako već nije udomljen😂

[@DShomemade]

Hehe udomljen je već kod mene 😂😂

[@ragibtufek]

@@DShomemade auuu....za dlaku je bio moj😂😂😂....

[@v.s.8759]

Kad te navata inspekcija bice ti po ušima😂😂

[@tomazk2638]

Super je vais m'en fabriquer un aussi 👌🔥

[@PH020]

Should do a temperature check before and after

[@labradoodle5097]

Nice job!

[@AuditorsUnited]

diesel heater glow plug seems relevant here

[@dmauka]

Krasno. Jedno pitanje, da li je mogao da se montira ventil direktno ispod posude za ulje i da ta posuda bude montirana direktno sa ventilom na cev za ubacivanje ulja? Tako bi svo ulje iscurelo (bilo utrošeno) iz rezervoara a i ne bi bilo otvorenog presipanja sa spoljne strane. Za vizuelnu kontrolu bi mogao da se ubaci neki providni element na putu dotoka ulja. Šta misliš o tome?

[@DShomemade]

Može se i tako odraditi da! 😉

[@nedudki]

California, here I come ! :)

[@Josh-ew1le]

The feet on the legs are a nice touch

[@Jimmywuu636]

Build a waste tablet furnace next

[@gt40f]

You forgot the fire test for the tablet.

[@josephbaguma83]

Hello there thanks for showing us I love that tablet how do I order for it

[@alexbiss9544]

awesome build just Kyrios though why no paint on the pipes.

[@cabmanist]

Did you use normal carbon wire to weld that to stainless?? Just learning here but i didnt know it was possible

[@torbjornnostdal2999]

It works just fine👍

[@aleksanderbye5917]

Great job, but you should suck air from outside, so that you dont remove the hot air from inside your workshop. 😄

[@RakTheGoose]

heat rises, and this being on the floor will remove the cold air from the workshop floor

[@aleksanderbye5917]

@@RakTheGoose the hot air from the stove will circulate the air, simply by heating it. No need to use inside air to get circulation 😁

[@branchandfoundry560]

My thoughts exactly. Has to be makeup/supply air from somewhere when exhausting to outside. I wonder what net gain is, setup as shown. Not knocking, honestly curious about the numbers...sorry, I'm a nerd & love numbers!

[@peterkn2]

But the air outside is heavily polluted from burning motor oil 😂

[@Maria-rd6uw]

Can you link the air pump what you use

[@JeanbenicoisJoachim]

Thank you you give me so much I m haïtien Joachim Jean beniçois good bless you

[@terminator2judgmentday30th4]

0:30 What is this? Is this is an espresso machine? No, no wait. it's a snow cone maker? Or is it a water heater?

[@olivermain5078]

That BMW is ❤

[@DavidParker-cf2km]

A Mercedes.

[@ingokuhn4192]

Wenn das die Grünen sehen kriegen die einen Kollabs😁😁

[@danielgoodkat2379]

Eigentlich jeder weil das konstrukt blödsinn ist

[@arvedblohm693]

# TEAM MELONEEEEEEEE !,!!!!!!!!!!

[@karelmarx8899]

f..k the greens

[@stoneyswolf]

Most of the heat is being blown out the exhaust pipe salamander heater for the win.

[@dejv1111]

Můžeš si tam nainstalovat různé přepážky nebo nahřívat keramická tělesa nebo šamotové desky a účinnost hned zvýšíš. Nebo dovnitř nainstaluješ výměník s vodou a rozneseš teplo do radiátorů.

[@БақытАлматыв]

Ортадағы асқана ыдысы өте жұқа отқа төзімсіз, әрине ұзаққа төзімсіз.

[@alfredogarciaroman8960]

Sois un máquina me encantó tu vídeo y le pusieras traducción a español increíble gracias por mostrar tus habilidades

[@damiencurran856]

So when is he going to start making the oil burner😅

[@pewpeww556]

Most janky and genius thing I seen on you tube. I like

[@kekibro3086]

Super videooo Davide