I love it...You're an amazing Mechanic...Especially Being That you're able to make at least 2 to 3 videos everyday...#AMAZINGMAN
@JoesBusBarn5 жыл бұрын
Tilden Young We had a lot of work this summer. That is why I was able to get quite a bit of footage. It is going to slow down a bit ounce school starts. But I’ll keep posting. Appreciate your comments buddy. Glad you like the videos.
@tildenyoung20885 жыл бұрын
Sure thing
@nigelmielke47063 жыл бұрын
What's the quoted time on this job?
@tildenyoung20883 жыл бұрын
@@nigelmielke4706 what are you asking in exact...???
@nigelmielke47063 жыл бұрын
@@tildenyoung2088 Replacing the just the valve cover gasket
@k-pop1235 жыл бұрын
I enjoyed your video.🍎👍 I respect your great video.🌹🍅 ❤ my friend. ❤like + 👍👍👍
@JoesBusBarn5 жыл бұрын
Appreciate the comment. Thank you for watching the video.
@napoleonarmstrong36484 жыл бұрын
So this is basically the process when replacing injector seals? I was gonna ask if thats the gasket I needed with the wires coming off. Didnt want to order the wrong one
@fluffypuppy7205 жыл бұрын
Excellent video, thank you!. Do you think that it’s possible that too much boost can blow this gasket and cause oil to leak into the intake port and burn oil? I think that is what is happening with my bus.
@JoesBusBarn5 жыл бұрын
Joe Drnec these particular engines issues are crankcase breathers. They cause oil to flow through charge air cooler and feeds into engine through turbo. A subscriber commented and we looked into it. It just so happens he was right. Looking into updating crank case breathers on these maxxforce engines. Let me know what engine you have so I can try and point you in the right direction
@fluffypuppy7205 жыл бұрын
Joe’s Bus Barn I have a 1996 mechanical DT466 with the valve cover gasket that is also the intake gasket. I believe oil is leaking into the intake and causing it to blow a lot of grey/blue smoke. Smoke goes away however when the turbo spools, and the compression checks good, the valves are dry, it is a low mileage engine. The turbo was removed and tested, it has no seal leaks and is within spec. My suspicion is that boost ruptured the gasket between the intake port and the valvetrain and is now taking oil into the intake at idle but once boost is added it pushes it out
@JoesBusBarn5 жыл бұрын
Joe Drnec Gasket itself is made to wristband pressure (turbo) but yes. I have work on very few mechanical dt’s. The ones I did. The gaskets were worn and oil was sleeping through. When ur turbo spoils at higher rpms. Pressure builds up on ur intake side and allows less oil to seep through. I think your diagnostic is correct. That’s where I would start.
@fluffypuppy7205 жыл бұрын
Joe’s Bus Barn Thank you for the reply!
@edwinflores20722 жыл бұрын
Primo una pregunta si está disponible
@notkirill69914 жыл бұрын
Hey I have a 2013 international maxxforce I was wondering if a leaking valve cover gasket can cause power loss?
@JoesBusBarn4 жыл бұрын
notkirill Leaking valve cover gasket will not cause power loss on this particular engine.
@MrSimon3472 жыл бұрын
where are you located?
@JoesBusBarn2 жыл бұрын
Rio Grande City Texas
@elpro46842 жыл бұрын
Buenas noches maestro como puedo comunicarme con usted colega por favor