DT466E/DT466 High Pressure Oil Pump Replacement

This Video Show How To Replace The High Pressure Oil Pump. And How To Remove Or Replace The IPR Valve On A International DT466‪@dairleautoclassicrestorati6892‬
#oilpump#truckrepair#truckmaintenance

[@burtonch]

Great video well done.

[@mikecase267]

I watched this man step by step to replace my water pump and he was clear on every bolt every bracket.. just a satisfying achievement to feel my heat and watch the temp guage climb no higher then 180' ...Thankyou sir !

[@dairleautoclassicrestorati6892]

Thank you Sir!

[@towm8ter]

Doing this job today for first time. It's do or die since truck is parked at my gym and could get towed. Appreciate the clear and simple instructions as well as tool sizes

[@dairleautoclassicrestorati6892]

👍🏽

[@FIWB.e90]

Did your issue get fixed?

[@dairleautoclassicrestorati6892]

@FIWB.e90 Yes Sir

[@vivvasbill]

Where did buy the part

[@dairleautoclassicrestorati6892]

@@vivvasbill from the International Dealer Parts Department

[@rickytaylor1945]

Thank you for your videos man. They really help a lot. Appreciate your hard work and for your showing to everyone how to get it done.🎉

[@dairleautoclassicrestorati6892]

I thank you for your comment!

[@jpage19591]

Thank you for all your vidos on 4700 HI YOU ARE a very good teacher

[@dairleautoclassicrestorati6892]

I thank you very much!👍🏽

[@palkoenergies7790]

Good video man, you make this look easy. And you realy take the time to show each step

[@wilbertcasher]

Thanks seeing this video gives me confidence I can do this as well.

[@soulfuldos]

All your videos are very helpful. Keep them coming my friend.

[@dairleautoclassicrestorati6892]

Thank you!

[@mellionare]

Thank you for the video

[@reychingon74]

Love your videos

[@dairleautoclassicrestorati6892]

Thank you!

[@jasonmiller8167]

Will only certain scanners work on this motor? I’ve got a scan gauge for a 7.3 already

[@dairleautoclassicrestorati6892]

You will need the round 6 or 8 pin connector. And if your scanner have the Heavy Duty Software. You should be good

[@user-kq8sg2ru1e]

Thanks bro

[@xavierbaker-in9xs]

I have a 2004 international 4300 DT466… would this be the same setup on mines as yours as far as gaskets and part numbers?

[@dairleautoclassicrestorati6892]

Good question, I would call a International Truck Dealer and give them the last 8 of the vin#. The Parts Department can answer that question. Thanks

[@tulioescobar3540]

Para desmontar bomba del international DT4300 2004 es lo mismo oh es diferente ?? Solo 2 tornillos oh son mas

[@dairleautoclassicrestorati6892]

La bomba se verá muy diferente. Pero el procedimiento es el mismo.

[@davidjohnson-iw6vj]

Did you have to prime the fuel system to get the air out after the hpop replacement?

[@dairleautoclassicrestorati6892]

No sir

[@user-jf9bp6mo3i]

I have a similar issue with a dt466 engine cracked cover plate around compressor leaking oil. The engine runs and sounds great. The vehicle is for light use. How long will it last if I just run it this way and keep up with it on oil, indefinitely? What could happen if I just continue to run it this way? Thank you

[@user-jf9bp6mo3i]

high pressure oil pump is fine, just a cracked cover plate

[@dairleautoclassicrestorati6892]

@user-jf9bp6mo3i Just keep an eye on the oil level. Most likely it has a low engine oil shut off device. But you do not want to ever run low on engine oil.

[@user-jf9bp6mo3i]

thank you @@dairleautoclassicrestorati6892

[@dotunepeters1886]

Hello Sir, Good morning to you Sir, I currently have a 2003 Durastar am working on. I am having no oil in the reservoir in front of the HPOP, truck has been started with shorts so engine runs but shuts of. Though am not a mechanic but I work on my stuffs by myself. Here it is; I learnt there is a regulator prone to stick open behind the oil filter/cooler. Already pulled it but I guess the regulator is on the crank case. Could you please point me to how I can remove this and also explain how I can test or check it to validate if it is still good. I got one in hand in case it’s bad, I can literally push it with screw driver and I can tell it is spring loaded. All type of help will be welcomed Thank you in anticipation . DIY PETERS.

[@martinsittle3185]

Hi. Im kooking for a diagram for this hp oil pump. Do u have any udea where i can find one?

[@reparandoando5782]

Cuál es la presión de apriete de los tornillos que sujetan la bomba a la tapa de distribución

[@dairleautoclassicrestorati6892]

Esa es una buena pregunta. Apriete el perno no mas de 20libras-pie.

[@reparandoando5782]

Es correcto, después encontré la tabla de aprietes del DT 466 E y así lo indica Gracias por tu respuesta 👍

[@juanvergara9266]

Should the engine be set on time before removing it?

[@dairleautoclassicrestorati6892]

No sir, just remove old pump and install new pump.

[@Lil_Chihuahua]

I have 97 4700 and it looses fuel pressure overnight I've replaced both fuel lines,primer,and all o-rings going to lines,it starts but will not hold prime still. Could the ferry ball cause this problem I'm stumped?

[@dairleautoclassicrestorati6892]

You are still getting air from some where. In the past on the 95-97's. I had to replace the plastic Fuel Lines. It's very hard to tell if they need replacing.

[@BobBob-yd8xf]

So if you have 0 oil pressure, How do you determine if it is the High pressure pump or the the other pump on the front of the crankshaft? Thank you.

[@dairleautoclassicrestorati6892]

My Laptop showed me that it was the High Pressure Oil Pump.

[@BobBob-yd8xf]

@@dairleautoclassicrestorati6892 Thanks bro! Good video btw! God Bless you and yours man!

[@josecarbajal1164]

can high pressure oil pump cause oil to get into the fuel tanks? or cause the injector seals to break if the ipr is broken?

[@dairleautoclassicrestorati6892]

It sounds like leaking Injector O-Rings allowing Oil to push into the Fuel Rail. This will allow Engine Oil to go into your Fuel Tank.

[@josecarbajal1164]

@@dairleautoclassicrestorati6892 thanks for the reply

[@robertmann3353]

What year DT466 is that truck? I have a 2003 International DT466 that I believe my high pressure oil pump has gave out. I'm trying to locate a part number before I pull it out.

[@dairleautoclassicrestorati6892]

It's a 2000

[@robertmann3353]

Thanks for responding. If my high pressure oil pump is bad, would that prevent my truck from running on ether?

[@dairleautoclassicrestorati6892]

@Robert Mann that is a good question. If the Pump is bad. It would be very difficult to start it on starting fluid. Keep in mind that these pumps are very expensive. I would highly recommend to put a scanner on for vehicle before you purchase a High Pressure Oil Pump.

[@tulioescobar3540]

I want to see the 2004 international DT4300 2004

[@onetoptecnologia9032]

Hey which scanner you used?

[@dairleautoclassicrestorati6892]

I used the DLB Diamond Logic Builder.

[@dairleautoclassicrestorati6892]

Or sometimes I get lucky using the Genisys EVO

[@Knightowl916]

What year is this ?

[@dairleautoclassicrestorati6892]

2000

[@manvan8288]

It’s that the same pump on the 2012 Max force 13

[@dairleautoclassicrestorati6892]

No sir

[@Knightowl916]

Is it the same for a 2011? Dt466?