Dual PC stream setup - Mixer explanations - Behringer X1204 USB

Explanation of how mixers work and what controls what.

[@Riker-eq2yv]

Absolutely the Best instructional video on the Behringer X1204 on KZbin

[@JakeSkillman]

Agreed, why can't every video be just like this.

[@BobbyPowell]

Because most ppl, like me, don't have a clue. The difference is, I don't try to make instructional videos. LOL Ernst hooked me up!

[@heraldoramos2563]

Hi, I want to set-up karaoke using KZbin as the source of my lyrics and music. I bought BEHRINGER XENYX X1204USB and J-Tech Digital Optical SPDIF Toslink / Coaxial Digital to Analog Audio Decoder Converter with PCM , 5.1 Dolby Digital & DTS. I also have an Onkyo receiver HT-R593 and a wireless microphone (GTD Audio G-380H VHF Wireless Microphone System with 4 Hand held mics). My problem now is how to connect the mixer to the receiver. What cables /connectors I need to use. I don’t have any knowledge about audio/video technology. I only watch KZbin. Please help. Thank You--- Heraldo

[@SDGolfGuy]

Steven Richards make sure the alt3-4 buttons are pressed in properly. Line in should be game pc only, mic in should be just mic via usb. The routing is usually controlled by the alt3-4 channels.

[@mayjar1]

Agreed. Very clear - unlike many others. Well done.

[@KaZeBeatz22]

Casually slides the hand cream away

[@matthewlloyd5989]

Lmao i thought the exact same thing, 4 years later...

[@jddjian]

Not far enough away to forget 😆

[@pthomas36]

Just picked up a used 1204FX, and this was the absolute best introduction to it I could have ever hoped for. Thanks so much. Probably gonna watch it again.

[@MilesBeyondThePast]

Been looking into buying a mixer to up the audio of my stream. These videos are helping me a ton to make sure I have it all setup right.

[@promixing7714]

Really solid, straight forward info on this mixer Ernst, thank you for taking the time to do this for us.

[@derekjenkins3250]

This is one of the clearest explanations i have come across in hours of searching on how to use a mixer .This also happens to be my mixer so i use this now as reference.Cheers

[@SoCal_Isac]

thanks bud mic was picking up game and pc audio and sending it in a loop 3 years later and still an amazing video much appreciated

[@luvguitars]

Very good overview very useful and you have lovely soft hands too!!

[@SDGolfGuy]

🙌

[@pety1245]

Txx man!! Finally someone who knows to explain! I am getting a mic, a guitar and a pick-up into the mixer.

[@synthaholic1]

Also, a great use for the AUX 1 PRE jack is to feed a subwoofer. You can dial in just as much as you need to the subwoofer, using the RED AUX knob, without it affecting your main mix/fader positions.

[@Glorious_Yell0w]

Ohhh LOL i searched for this mixer just random on youtube. Hahahaha and I got this hit. The Erny reviews, i miss em.

[@MadAl37]

This is the video behringer needed to make, bought this mixer, this video has been invaluable, well done and thank you! great job!

[@gerbans23]

Just got today a used Behringer Xenyx x1204usb it's good to see this video. In the next few days I hope I could learn a lot from this video. Thank you Ernst. Regards and Keep safe.

[@nathanbrewer6032]

Excellent job! Very concise, and most helpful, thank you. And keep up the great work!

[@Bangouaman]

Thank you! I have a Europower3000 that I'm still struggling with to some extent. Your explanations are to the point and clear!

[@LordCallen]

Extremely well done informational video. One of the best I've seen on the youtubes in all honesty.

[@saewms2616]

This video was just what I needed along with your other Dual PC video!! Awesome job!!

[@FirebrandVOCALS]

This particular mixer is great - used one last night, was impressed

[@gunnerlucario780]

Amazeing tutorial! The board doesnt feel as overwhelming as it used to.

[@delhughes1142]

Just came across this video... Thank you Sir explained well 👍

[@deancturnbull1669]

I understood that a lot better than other videos..must keep this to refer back to..was help full..learned a few things..i sat there saying...awww, i get it.

[@JWEEKS4397]

Thanks I understand my mixer a lot due to your vid. Very good Thanks again

[@juansalazar6451]

Great info! Recently purchased one of this mixers, still learning the process!

[@KWHCoaster]

Terrific explanation! Cleared up a few things I was unsure about.

[@Jyve]

Bloomin' awesome. Totally helps set things up (and make me want to upgrade to a bigger Behringer).

[@regmason2329]

I have to comment. I have a Behringer Xenyx 1832USB that I use for live music. Great mixer-BUT- 3 out of the 6 XLR inputs have developed heavy static. Behringer's customer service is a joke! So if it works it's great- BUT, if problems develop- good luck in getting it fixed.

[@Ressy66]

Fantastic, I've watched a few viz on this modem and nobody mentioned anything about the alt 3/4 (cue) BUT unless I had a micro nap, you did not explain the SOLO button? Been looking for a new mixer for streaming, and now I understand the cue via alt 3/4, aux send for skype, jitsi meet or even a phone, I think this is perfect unit, thanks heaps!

[@mercenaryex834]

Hi sir can i connect this mixer with Pionner DDJ RB controller?

[@kroshlord]

Great video dude, it's really helped me with my setup, as I really do not want duel mic's

[@ippaku]

Hey Everyone! i've just got all my cable setup and ready to start.I do not like using OBS Studio i do not find it stable for release but I will try. What I wanted to ask is that I would like to hear more of my game volume. I play counterstrike and I need to hear more bass from it but do not want to pass that to my stream PC. I've purchased all the cable and "noise" filters to match. everything in total including a new Microphone was just under $340 now did purchase the 1204USB Premium vs the standard I don't know why but I did. I will let you all know how it goes. I will do a video and follow up making sure to give credit to Mr. Blofield. With so many people here doing dual PC setups I wanted to ask a follow up question. One of the nice things in my current PC setup is I was able to take audio from my bot deepbot where I play music and direct that to the stream vs me having to hear it. So I could play CSGo and my viewers could hear me, the game and the music. All the while I was only hearing the game. Anyone have recommendations on that? I figured if ANYONE would it would be the 33 smart people that liked this youtube video. Thank you, ippaku

[@SDGolfGuy]

You should still be able to have different volumes/mixes of your game audio to your headphones versus to your stream PC in this setup FYI.

[@ippaku]

Thanks Ernst I will try again today I had to take a day off to relax my brain from a Migraine.

[@fiazmiskin]

Simple explanation. Excellent. Thank you!

[@JoeyTeckno]

I have this mixer and this is by far the absolute BEST explanation of how it works. Thank you so much! Something weird I'm noticing, which is perhaps something I'm doing wrong, I have an AT2020 XLR on line 1. When I listen to it on my headphones, I can hear the ambient sound very loudly, which makes me think the recording is going to sound terrible, however, when I record on my PC using Audacity or any other software, I can basically hear my voice very clearly with almost no ambient noise. So basically my question is, why is the preview on the headphones so loud as opposed to the playback? The mixer is connected via USB. I also noticed that if I connect my headphones to the Control Room outputs, the sound is much more like how it plays back after recording.

[@SDGolfGuy]

its just the raw signal is all, its the ambient noise of the voltage on the mic line. Take that with any sort of a gain filter or lets say reduction in windows input volume, or even differences in impedance and you get that background noise to go away.

[@JoeyTeckno]

Ernst Blofield thanks! I’m happy with how the recordings end up, it’s just annoying to not be able to monitor exactly what is being recorded. I’m just glad the noise is in the monitoring and not in the recording 😆

[@spiritofzen7022]

I’m wondering why I can’t get any decent reverb on mine as I thought it had built in effects which it obviously doesn’t or I’m doing something wrong

[@jaybub3442]

thanks alot after this vid i ordered one and ive just received mine

[@7caesar7]

Very well explained, thank u so much for it!!

[@latotayporota]

Wow, a great video...nice work dude. Hey behringer !!! this is the way to make a tutorial. Make one for each of your mixer models.

[@guittubed]

Excellent info. Thanks! Got none of this in the manual. Would be great if you could go into the effects more in depth. Also, there are buttons that cancel out the effects and mains, why? Took some trial and error to sort it out. This is a USB Zoom concert mixer for me and so far it's sounds great although it can be tough to get the instrument mic at a good volume without using all gain. I am a solo acoustic guitarist. Thanks again - very helpful.

[@LukasHallgren01]

Thank you! This video helps a lot! Credits from sweden! :)

[@Arty00120012]

you just sold this to me

[@siroz1]

Dude thank you so much for this.

[@gregsmith2644]

I brought the 1204 FX without the usb interface. Does a DAW (Ableton) see more than 2 channels coming in on the USB output of the mixer or do you need to feed from Aux, Alt3-4 back panel?

[@tonylongbui3654]

Appreciate for sharing this video

[@leprofesseur2045]

Very helpful video, after searching on the internet for a mixer that would fit my needs I came to this video, however there are still a couple of questions if you don't mind. My set up consists of a pair of studio monitors, a microphone and headphones which I have all hooked up to my pc. My main concern is that it doesn't look like this mixer has an USB audio input to which I can hook up to an output on my monitors and headphones. So basically a USB connection that transfers audio Computer > Mixer > Headphone/Studio Monitors. Thank you in advance

[@WillfoxPiano]

thanks for the tutorial. I'm wondering how I can send my mic through the usb but not hear it in my headset.

[@chongomillionaire7205]

yo... same

[@dougrobinson8632]

I need to use my NextKast software to go live on my internet radio station. It says connect to main out...the audio from NextKast and Line In connected to my computer. Can you fill me in on the connections and for a strange reason...I don't see line in in my sound panel 😢 help

[@everardovilla564]

Perfect explanation thx

[@MACODJ]

Hello, Is It possibile to control the main master, without put down the all volume inside the live streaming in zoom? So that people can listen the audio streaming from home very well, but from my speakers came out low volume? I want that the main master can be separate in output from all audio inside the mixer

[@ugvinyllettering]

Hello nice video I have the main outs hooked to my amp But can I hook a powered speaker up to mixer too And have in the same main mix?

[@Skoarch]

Even tho this video was well constructed and was executed perfectly. Im still lost lol

[@atgeki]

Just ordered this for streaming in our church service. Thanks for the review. Btw does it require an additional amp?

[@isyotuyala7032]

Hi brother, hope u can help my problem on my mixer is exactly the same as yours but i got trouble on my microphone there’s no echo i dont no how to adjust it. I used my mixer for karaoke.

[@revadan]

question. ALT 3-4 Outputs from the back, are they mono? can i use a TRS to XLR male from there?

[@PerryComics]

hey, fantastic video, i have one question. I'm using this for a dual pc set up and I'm getting some type of static noise from the gaming pc audio, audio cable 3.5mm to dual 1/4" TS into channel 7/8, any suggestions on how to eliminate that static

[@hubert17]

My USB Audio Device only send MONO audio from the xenyx mixer. In Windows Advance settings, Default Device is only 1 Channel or Mono. Can you advice me on this?

[@BinuJamesMathew]

Very useful explanation. appreciate every button explained. I'm looking for support on the same mixer to be used for karaoke live streaming for Zoom sessions. Can you please explain it n another video?

[@SDGolfGuy]

I would say it depends how you use it. One channel would be your mic, another could be your guitar. The USB goes into your PC and you just manage the volumes on the mixer.

[@drin4us]

Absolutely perfect ! Keep it so on !!

[@scentgrasslakerailway]

Excellent, thanks!

[@rcdude86]

i am curious to why you have the compressor all the way up?

[@SDGolfGuy]

Was probably just testing something at the time.

[@DJ-SPARKY-REACH-ON-AIR]

is the usb on alt 3-4 so i can put usb laptop music playing when i fade mics down i dont want to use main mix to fade as then it all fade out

[@erwinhudecloyd]

Hello Ernst, I have just bought the same "mixer" I'm using Ableton Live 10 Lite for recording AND NOW I CAN NOT RECORD MY MIC...???? I'm using standard sound card in PC M-Audio Delta Audiofil...could you help me please...???? many thanx.

[@carlosbernad7371]

Hi Ernst, Thanks for sharing your video. I was wondering if I send signal audio from PC via USB to the mixer, is this signal assigned to a channel to manage EQ, FX, balance and volume or is it only mixed into MAIN MIX by pushing down 2-TR/USB TO MAIN? Thanks! Carlos

[@Greentim67]

Waw,I've just bought this half an hr ag on ebay .thanks.

[@LeBulbe07]

the thing i'm trying to do is not exactly the same as you but maybe you can help. the reason i bought a mixer is to be able to input my MIC (audio technica AT2020), 1 echo dot (alexa) and 1 IPAD through discord. I also want to be able to hear myself(MIC) at the audio level i want in my earphones without affecting the output sound in discord. can you guide me to how i should plug and configure my things so i can do that ? also i have the 1204USB (not X) but i dont think that sould matter. right now everything works except that i can only hear my self too loud or not at all by turning to main mix redirection to my headphones on or off and if i put it to off i also loose the sound of my ipad and echo dot obviously. i'm really lost right now. oh and i tried using the ALT 3-4 wich was the reason why i bought this audio mixer in the first place but i only get sound from left ear (that might be my cable though).

[@jaybrodie943]

my question has to do with speakers I may not be placing them in the correct output. when I plug into the output there not very loud atleast not loud enough for a gig. do I need power speakers or am I totally not using this correctly

[@SDGolfGuy]

Depends on the output you're using. I think for most applications powered speakers are ideal. That's what I've always used.

[@sanacuriosidad]

thank you! very helpful

[@PurpScurpington]

Thanks for this! So you send your mic and instrument to your PC via USB, then your PCs to Alt3-4 and mix them back into your streaming PC via that PC's mic in jack I assume? And then combine mic (USB main mix) and PCs (3.5mm alt mix) into one track via OBS? I've got one of these and have ended up doing the same, although I feel kinda dumb still ultimately mixing in OBS because I mean... it's a mixer lol. But hey, at least I'm not alone. Three questions: (1) Do you know of any way to get FX from the internal processor on aux send 2? No matter what I do if I use aux sends I can't get FX on the mic. Although using a just-mics mix solves that problem for me basically. When I switch my mic from the USB main mix to 3.5mm alt mix, when I record my voice into audacity to test, they sound mostly the same but the waveforms look very different, even though I keep myself the same distance from mic and touch no settings. Any idea why? (3) There's no way then to isolate just game audio, e.g. if I wanted to record alongside stream and re-dub with new audio later, yeah?

[@SDGolfGuy]

So a couple comments, then I'll attempt to answer your questions. I use this setup to send ONLY my mic to the stream PC (I run dual PCs). The Aux send 1, sends ONLY my mic, to my GAME PC. My ALT3-4 only ever goes to my headphones, no other route. The GAME PC sends directly to the STREAM PC through line out/in connection (3.5mm). This means I have 3 sources in OBS - USB mic, Line in game pc, and "desktop audio." - For the game PC I use the line in as my mic, and default audio (speakers) out as the output. Hope that clarifies the setup because there are no loops you're hinting at. 1. The orange knobs send FX via Aux Send 2 to whatever 3.5mm or 6.3mm source. 2. Main and Alt mixes have different interfaces (USB versus analog) you simply may have some loss or added gain between the two - keep in mind the alt3-4 faders are separate from the main faders (USB will offer a cleaner signal usually because below a certain level there is no gain since its digital) 3. There are many ways to isolate game audio. If you're running dual PCs just do it how I did (game pc to stream pc direct line out/line in), if you're using a single pc you could run the game audio into the mixer, send it alt 3-4 into wherever you want it to go (back to line in?) depends on what you want to isolate in that ALT3-4 mix.

[@keithbarnes1321]

What kind of footswitch should be used latching or non-latching?

[@DobeMac]

I'm looking to invest into a mixer for my streams on twitch. I stream PS4 as well as PC games. I use an elgato HD 60 and Astro a40s mixamp as well as a dedicated streaming PC to stream whether it's console or PC gaming. Currently I get white noise and some feedback when I stream. I want to get this mixer but I'm not sure how to set it up. I'm a noob with all of this and really need a suggested layout dumbed down. Any suggestions? Also Is there a way I can set up my mixer with PS4 and PC audio captured? So it makes it easier to switch between them? Also What sound card do you recommend?

[@SDGolfGuy]

Your setup is a bit more complicated. I have a video on how to setup dual PCs using this same mixer as well. The difference between my video and your setup is I would probably use an HDMI switch to alter back and forth between the video source (PC hdmi and PS4 hdmi) before the cap card. In terms of audio that is where it gets a little trickier. You'll need to get the PS4 to send the audio out via the optical, into the mixamp, into the mixer itself, OR you can have the cable send it out via the controller to the mixer. You could also pickup a small USB audio card that will likely work with PS4 that allows it to come out the primary USB ports on the PS4. The mixer itself can do all the audio no problem, its really just how you want to connect it to the stream PC. You could also just send it direct via the HDMI which may be the easiest (but might have an issue in OBS when you switch back to PC - you'll have to disable the sound on the cap card for PC streaming). In terms of sound card I just recommend any audio that can produce at least 24 bit 192kbps audio quality, anything lower than that can have some noticeable quality loss.

[@TheWhatthefuck12]

THANKS for a clear pretty through explanation of basic (not to me) functions)

[@FirebrandVOCALS]

Excellent Overview .. Cheers!

[@billducas]

I have the same mixer. I've been looking for a video like this. It's excellent! I've noticed that you have to press the clip light on each channel in order for the meter to work during a live performance with all channels going. Is this the way it's supposed to work?

[@ExtremeReviewer101]

Quick question: What does Line IN 7/8 really do? Split the Left and Right into separate sources? Because when I use my 1/4 Inch RCA to 3.5mm, I only get the right sound to work fine. How do I get the left side of my monitor speakers to pick up sound??? I'm not here for streaming I'm here for audio playback. The Behringer mixer I have is a QZ1204USB, and the manuals still doesn't explain to me what LINE IN 7/8 does. I can get LINE IN 5/6 to work fine, but LINE IN 7/8 I don't know how that's done.

[@SDGolfGuy]

7/8 has two mono lines into one fader basically, offering it as a "stereo" input. Chances are you potentially have a wrong adapter. The inputs are mono, remember that.

[@ExtremeReviewer101]

@@SDGolfGuy Ahhhh, that explains why I can't get the left speaker to work, it's mono channels on 7/8...Huh.

[@dkamhaji]

hi thanks for the video! Quick question.. how do you set it up to send input from your computer say KZbin..coming in via usb and get it out through the alt 3/4? can this be done without connecting your computer to your input channels ? just using the USB cable? Alternatively, say you have your phone hooked up to the Tape in can you send/route that input out of the mixer somehow? to the 3/4 or control room? thanks!

[@SDGolfGuy]

You can’t use usb as an input to a line, I believe. You’d have to run analog out from pc. Then listen to 3/4

[@prosandcons4453]

Thank you for this.just a question.where is the main out for quarter inch cable?thank you for the reply

[@SDGolfGuy]

On the back :)

[@KalonaSuperNatural]

My inputs are audio from 2 microphones (line 1 and 2) and computer audio. I want to hear both in my headset but can't hear the computer audio. (Drivers were installed and it was working but then I must have pressed some buttons.) I've tried every combination now. What should I do? (This is so I can do a live video broadcast with two guests on mics at the board as well as guests who video conference into the computer/browser via restream.io).

[@SDGolfGuy]

if your computer is outputting via USB then it can't be used as an input just make sure its on USB to main and it should come through main with the mics.

[@johnboy88ism]

Very educational...thank you*👍

[@Aaron.Broomfield]

Incredible Video, thank you soo much !!

[@jimgerth6854]

Important question: does the red USB/2-TR button (the top one in the SOURCE section) mute the ALT 3-4 track for the control room output? Or do they also get mixed together like when you press ALT 3-4 and MAIN MIX at the same time? I need to have both the USB Input and the ALT 3-4 track output to the control room together

[@SDGolfGuy]

Nope, it doesn't mute it, it adds it or subtracts it to the source

[@Jeyfreeofficial]

I have a problem with that mixer, I have it connected to my laptop, also have some monitors audio mixer and headphones all connected to their corresponding inputs at the time you want the audio coming out of my laptop is only heard in the you headphones and not on the monitors do not, it stops listening on both, as I solve the problem?

[@mrdavidajordan]

Very good video. Thank you.

[@thealphajourney6108]

Hey Ernst, I'm having a really tough time with my Behringer Xenyx 502 (non USB version) mixer. I've been trouble shooting for a week now, and was hoping you might know the solution to my problem. My setup is I have 2 PCs : One gaming PC and one Streaming/encoding PC for twitch.tv. I bought this mixer to connect my gaming PC audio to my other Streaming PC. This mixer will allow my streaming PC to hear everything playing on my gaming PC. My problem is that once connected to the mixer, all i hear is loud static. It doesn't even show to be a connected device in the devices and printers section on either PCs. The program that i'm using to run my streaming is called OBS. (studio version). In the audio settings on OBS i have my Line IN as one of my aux audio devices, so that should pick up my gaming PC audio, but all that it is picking up is what sounds like static. I DONT have a static remover connected to the mixer because i thought that it would only be necessary for low amounts of static in the audio. I don't know if NOT having a static remover will make my audio completely distorted, or if the static remover is designed to help treat already comprehensible audio signals. My connections are as follows: Gaming PC Line out to LINE IN on the mixer. (RCA to 1/4" connection) LINE OUT on mixer to my Streaming PC LINE IN. (RCA to 1/4" connection) These are the correct connections for a dual PC setup, but the audio never gets through. I turned down my levels on my mixer, disabled all sound effects on my LINE IN settings under audio devices manager, but all i'm getting is static sound. *Is a Ground loop/Ground eliminator necessary to get any audio in my situation? *Is my behinger 502 faulty? The Power light is orange, but no levels are being shown (Green or yellow light indicators) *Are my devices not selected properly? *Do I need a dedicated sound card for this setup? (currently using motherboard sound interface) *On Amazon (place of my purchase) I have read reviews on the power supply being faulty. Would this contribute to my distorted signal? I'm a complete audio novice and would appreciate a reply. Please, I really want this to work for my streaming setup on Twitch.tv. Thank you!

[@Avidcomp]

No, I didn't see your video on : "2 PC's using 1 mixer, 1 headphone and 1 microphone", may I have a link for that please?

[@dominiquedionisio1026]

Hello Sir! your video helps me a lot in understanding this behringer mixer, however, may I ask you if this mixer's USB out is capable of sending stereo signals to computer? thanks in advance

[@SDGolfGuy]

Its stereo from stereo inputs as main mix

[@baskinbobbins2718]

Hi Eric, I've been following your guide on dual pc streaming, to which is an awesome guide by the way, and I've been having an issue. Sound going to the stream pc sounds like it's in an auditorium or cave. I purchased everything you had listed in your updated diagram including the Behringer x1204usb. Do you have any thoughts? I don't have any of the mics set to "listen to" and I did use the software video to make sure everything was set up, the only problem with that is there isn't a line in option for Mic/Auxiliary Audio Device 2 in OBS. Thanks in advance and sorry to bother you.

[@baskinbobbins2718]

OK, never mind on the line in issue. I had it plugged into the mic in on accident. So now if I just use mic/aux 2 in obs, the sound is fine. The desktop audio in OBS works fine as well. However, Mic/aux is the one with the auditorium sound, which is the microphone usb audio codec.

[@baskinbobbins2718]

The mic/aux is also picking up everything from the gaming pc as well. Alt 3/4 button is pressed.

[@SDGolfGuy]

It sounds like the red knobs aren't turned down properly, or the orange knobs. If you're hearing a cave like sound it seems like there is some sent audio from aux send 2? did you perhaps plug in aux send 2 instead of aux send 1 to the wrong PC? If not, check the "RECORDING" devices on stream PC and make sure in the "LISTEN" tab the "LISTEN TO THIS DEVICE" is unchecked.

[@baskinbobbins2718]

It seems I didn't have the red/orange knobs turned down properly. I had them the way they were in the diagram and now I have them positioned as this video does which fixed the problem with gaming PC sound going to stream PC via microphone usb audio codec. So that's great! Now the only problem is the cave sound coming from the mic. I have the gaming PC connected to aux send 1 and there is nothing in aux send 2. "Listen to this device" is not checked on either PC. The microphone works fine when used on the gaming PC.

[@baskinbobbins2718]

Well you did it. I forgot about the red and orange knobs on the right of the mixer. I turned them down and everything works fantastically. Amazing guide and much appreciation for the quick and helpful response.

[@spedled9520]

I have an issue when I stream with this mixer. My friends say their voice echos when I have the ps4 controller plunged to L/R audio in and 3mm Jack plugged to controller to head the sound of the PS4 game play in my headphones. However, I don’t hear them echo and everything sounds good on my end. Am I plugging my sound in/out wrong?

[@ALFAATV]

USB cable goes in which pc? im trying to do a similar setup, but instead of a gamer pc, i pretend to use a ps4. Using the mixer to both console and streaming pc. Nice video btw, best explanation on this kind of setup here on yt. ps: sorry about my english, im brazilian (:

[@SDGolfGuy]

Stream PC

[@DankyMurphy]

What if you have an amp with your headset for gaming? Like Creative Sound Blaster X7 paired with the beyerdynamic DT 990 PRO? Could I combine it all with the mixer (Xenyk q1002usb) the model I have?

[@SDGolfGuy]

Yes, you can hook the amp up to the headphone out if you'd like have the headphone out on the mixer go into the line in on the amp. Works all the same way.

[@willclarke8604]

can you send channels into the headphone mix , for example listen to one channel on it's own on the heapphone mix ?

[@SDGolfGuy]

Yeah essentially that is what I'm doing with both game pc and stream pc

[@dickyvalex8094]

Followed this to the T and have an issue with mic quality.. the Stream PC uses the USB cable and sounds amazing. I use the 3.5mm for the Game PC and I'm told that in game and in Discord/ TS I sound very bad. Very low and/ or high but very distorted. I have been told I sound like a demon screaming in a mic through a pillow (?) but I'm confused as to why. I have the Behringer 1204USB and only use the output for the mic line going to the Game PC.

[@SDGolfGuy]

Well if you're using FX send you might have some FX added to the mic which makes it sound that way, if not you may simply just have your aux send 1 lines with too high of volume, this can lead to increased gain and be staticy and over driven.

[@levia9753]

So what cables am I going to need to route audio to my laptop, and also my PC. I don’t believe it came with the ones I need. I just bought on amazon the thing with the 2 thick aux into the small 3.5mm cables cause I’ve heard that I needed that. What all cables am I going to need for a PC/Laptop setup

[@SDGolfGuy]

Levi A cables are variable as to what you wanna do, I have some other diagrams for other utilities that may give you some ideas

[@levia9753]

Ernst Blofield I’m not sure if the mixer I bought is going to work for what I’m trying to do... this is the exact product I bought “Behringer XENYX 1002-10 Channel Audio Mixer and Accessory Bundle w/ 5X Cables + Fibertique Cloth” I’m looking to do a dual stream setup and I want the audio routed from my gaming PC and my laptop going in to 1 mixer so they share the same audio if that makes sense. What cables will I need for this? And will this mixer even work?

[@yanzee8604]

If i have two mics connected on 1 and 2 can they have a diff fx on both of them at the same time?, example echo on mic 1 and hall on mic 2? And can i mix 2 built in fx on 1 mic?

[@SDGolfGuy]

No you can't have two different without changing the knobs and muting one of the mics. No mixing FX's.

[@jordanharms1864]

So I had a question. I can not seem to get the sound from the streaming pc to go to the headphone unless i do it through the usb. When i do that though I cant control it, as well as can only get it to obs by bypassing the mixer. Any ideas whats going on?

[@crux1179]

What if i wamt to record everything to.my main mix, and only send for example line 1 and 2 to alt34 mix, is that possibke? Can i record everything through main into my.pc, amd sent out only a few of those channels?

[@theUPTOPKID]

If i have this mixer and a USB microphone where would I hook it up at to the mixer?

[@SDGolfGuy]

Can't hook it up, not meant for USB mics.

[@Jaysbart23]

How can i set it up for PC karaoke thru home stereo.

[@TON3LOC27]

Hey man great vid. I have a question, I also am running a Rog Swift and am having trouble getting it to work with my streaming pc and Elgato hd60 pro. what adapter are you using?

[@SDGolfGuy]

For a cap card I use MAGWELL X1000ie-4k or something like that - only one that will natively work with 1440p

[@shadowstryker1125]

where goes the aux send? i mean where it connects (sorry if my question is stupid i really dont know)

[@TonysGoodLife]

Could you do a video setting up a Sm7B with this mixer ?

[@SDGolfGuy]

its the same thing, just use the SM7B

[@IgarashiDaichi]

Very interesting and useful video, but why you would listen again your streaming/gaming pc? Aren't you using the usb interface to listen? I'm a bit confused here

[@SDGolfGuy]

USB interface doesn't listen to it, only sends it.

[@IgarashiDaichi]

@@SDGolfGuy oh noes, so it isn't like an "audio interface", you get only the mic, is that correct?

[@SDGolfGuy]

@@IgarashiDaichi no not exactly.

[@IgarashiDaichi]

@@SDGolfGuy I see, I'm still a bit confused but ok. Anyways, this is only one of 2 videos that explains how to setup a dual pc mixer in a smart way, sooo good job on that

[@connectedevolution]

Is there any reason why I wouldn't hear any effects through the headphones while I am monitoring?

[@SDGolfGuy]

Depends on your FX loop and whether they're captured in your listening device. If you're sending via main and listening to alt, you won't hear.

[@SuperStruct]

What mixer should I get if I only am going to have 1 xlr input but want all the good features

[@SDGolfGuy]

Pretty much teh Behringer X1204USB is the minimum mixer you want to have 1 XLR input but dual outputs - sadly there is no company I've found that has less inputs - say 1-4 that hvae dual outputs. Perhaps soon.

[@SuperStruct]

I only need 1 USB output, but it seems like anything with less inputs/outputs also lacks the processing power