Thanks Lee for all the amazing work & passion you have for Porsches and our community. You really make a difference & it’s hugely appreciated. Toby 🙏
@9WERKSTV2 жыл бұрын
Wow Toby, I am humbled. Thanks a lot for your kind words and support for my work, I am hugely appreciative of your gesture. My work would amount to nothing if there was no community or audience behind it - it is YOUR passion which keeps me with plenty to do. Thank you.
@Van-tastic2 жыл бұрын
Lee, my M96 is built to 3.7L (I kept the short stroke crank) and revved to 7600RPM. There are zero issues. What your man said about “a healthy engine” is where the superstition about the M96 comes from. People pick them up cheap and then attempt to hot rod a neglected engine… that doesn’t work out well.
@ferencmihala53462 жыл бұрын
Where did you have it built?
@Van-tastic2 жыл бұрын
@@ferencmihala5346 Jason @ 9XX Motors.
@ett_baer2 жыл бұрын
@@Van-tastic How much did it cost out of interest? I'm thinking of going nuts with my car and getting a 3.7, coilovers, rollcage etc. The only place I've looked at engine wise is Hartech.
@Van-tastic2 жыл бұрын
@@ett_baer I’m not sure how relevant the price would be today since it was 2015 when I had it done, but it was around $15k.
@wesleycarusos8225 Жыл бұрын
I did the resonator delete mod. I have not done the air filter or the plenum. I did do the air filter on my Boxster and I thought maybe a little bit but I got to tell you the difference with the resonator delete is unbelievable ..my car pulls so much harder at 3K now. It also feels like it's spools up quicker. It's not the extra noise because I don't know that there is a whole lot of extra noise I like the tone of the exhaust better. Surprised this mod can make a substantial difference in the tone but it does and it's nice.
@Flat6_9112 жыл бұрын
Would have been good to see the plenum and filter run separately, the K&N is actually an effective mod in isolation on these cars, good to see there was some improvement though! 👍
@chriscarbaugh39362 жыл бұрын
And they pass more dust 🙁; proven!
@TheGinger12 жыл бұрын
This is what I was going to comment. I would want to know which one is making the most difference because one is considerably more expensive than the other.
@danjo9112 жыл бұрын
Exactly the same comment. How can you deduce what each does when you change both at the same time…..pointless really if your intention is to prove a difference made by either mod.
@9WERKSTV2 жыл бұрын
That's a good point, Ben. Maybe next time!
@marcusoutdoors4999 Жыл бұрын
I think it proved a useful power gain can be had through better breathing, but separately I’ve seen the K&N tested in isolation and it was good for a couple of horse power and also improved the induction noise.
@berniedmd19012 жыл бұрын
I put an after market Plenum on my 2020 Porsche C2S and I immediately noticed a bit more torque and top end pull. I first had a GIAC Tune done with an Akrapovic exhaust with a High flow catalytic converters. On my Dragy I pulled a consistent 2.90 sec 0-60 and a 1/4 mile of 10.66 sec here in Orlando Florida at about 1000 ft of air. After placing the New Plenum I gained around a 1/10th at 2.80 sec 0-60 and a 1/4 mile of 10.50. It was well worth putting on the Plenum, but in the 992 it does require about 4-5 hours of work to get to the part and replace it. But again well worth it as in city driving the increase torque is Soooooo worth it!!!!
@dannsmcshane12332 жыл бұрын
Thanks Lee i have been rebuilding a 997 4s for 15 months i have did the same mods as your self and the titanium exhaust and bigger throttle body
@9WERKSTV2 жыл бұрын
Nice, will be looking into the bigger throttle body.
@michaeljohncox38982 жыл бұрын
Thanks for the informative video Lee. Due to my 2001 C4 having an actual GT3 wing put on by the previous owner instead of the aerokit wing I had to go with the Fabspeed intake. I don't know if it improves performance but the sound is unbelievable at high RPM. I don't tell any Porsche enthusiast it is on the car because I don't need the 20 minute regurgitation of the internet concensus that I have ruined my car because I don't have the stock airbox. I will add the IPD plenum to my list as a possible mod for the future. Enjoy your 996!
@michaeljohncox38982 жыл бұрын
One more comment, the only dyno that matters is your butt dyno! The only thing it needs to be adjusted for is to pass wind - yes even in a 911!
@9WERKSTV2 жыл бұрын
Thanks Michael! Yes agreed, the one true metric is how the car feels to YOU! Data etc is all for pub talk, and for some people on the internet to get very anal and angry over!!
@JimBob_19752 жыл бұрын
You're a good presenter and come across as a decent guy, keep up the good work 👍
@9WERKSTV2 жыл бұрын
Thanks James!
@Lee-zk8vu Жыл бұрын
I have an '11 Boxster Spyder (related engine I believe at 3.4 litre). I installed IPD TB, intake plenum, Soul header and exhaust, Cobb tune, K&N filter. I've not had it dyno'd. However, I owned the car since new, and just completed the above mods 1 year ago. The increase in power is palpable in a 2800 lb vehicle. (Also installed Numeric shifter, which is amazing.). The car is transformed for me. You might go a bit further with yours. Best of luck. I enjoy your content very much.
@tlib7 Жыл бұрын
Awesome video! Very informative. I’m having a IPD Plenum / Throttle Body & K&N filter installed Friday on my 2003 C4S, can’t wait!!! All the best & keep up the great work!!!
@quentingiroud Жыл бұрын
Happy with the results?
@tlib7 Жыл бұрын
@@quentingiroud I'm extremely happy with the results. It's been 7 months now since installation & definitely a recommended modification.
@GTSCarLife2 жыл бұрын
Another brilliant video Lee! Informative, relevant to your audience and something not generally being done! Great job!
@9WERKSTV2 жыл бұрын
Thank you. I only wish more people could see this sort of stuff instead of watching KZbinrs go get coffee in press cars!
@GTSCarLife2 жыл бұрын
@@9WERKSTV I agree 100%. My view is that you create your body of work, make it high quality, and know that it is something you are and will be proud of. Eventually people will appreciate and judge it on it's own merit. What you are doing is really special in the automotive KZbin space, and I do believe you will gain the audience and accolades you deserve. I know it can be frustrating to see an endless parade of teenage girls post iPhone videos on their new boob job, and instantly gain a million views and subscribers, while the work you are doing requires so much more planning, time and money. The world is a crazy place! In my situation, I have the further challenge of a full-time and highly successful career in another industry, so my channel is my passion project, but I do not have the luxury of giving it the time I would like. With your experience, access to important players and automobiles in the Porsche world, combined with your innate sense of what makes for unique and quality content, you WILL succeed. Keep plugging away at it. When it comes to automotive journalism, I will live vicariously through you mate!
@chriscarbaugh39362 жыл бұрын
Dynos frequently give very different results. Just because it was remapped at 320hp, doesn’t mean it would have been 320 on this dyno. The key is the back to back testing you have done. Nicely done at that!
@9WERKSTV2 жыл бұрын
Thanks Chris.
@manuelmartineznusn8 ай бұрын
love the 996, even better than 993
@harrypalmer62282 жыл бұрын
Thanks Lee - good work and very interesting. Would like to have seen the stock map reapplied, values taken, the mods added, values taken and then a specific remap for the added items with a final value.
@fairfaxa4 ай бұрын
Another superlative Video Lee. I opted for the Castol oil bottle lid and noticed a little oomph and some more BASS. Added to my cans that have had some baflles removed and the sound is lovely., Keep up the great work!
@nigelvergas6103 Жыл бұрын
Thanks Lee. Nigel.
@9WERKSTV Жыл бұрын
Oh wow, thanks Nigel. Very kind good sir.
@fairfaxa10 ай бұрын
Thanks Lee... my 98 3.4 is now going to get the helmholtz mod ... had been a sceptic before watching this!! thank you
@tonyfot02 жыл бұрын
Great to see a methodical approach to engine mods with before/after rolling road, rather than figures quoted without any evidence. Been sceptical on these plenum mods, but would consider it a mild upgrade in the future. Thanks again
@siri18022 жыл бұрын
Cool video! Mate, you and a couple other KZbinrs helps me along in my decision to buy a 996 c4S 2 months ago here in Aus. I swear I watched your c4s best non GT 911 video at least 20 times! Anyway thanks for the efforts and this video is something I was looking into also and just popped up from you fortuitously for me… think I’ll go ahead and get my Hemholtz and IPD! Thank you.
@9WERKSTV2 жыл бұрын
Thanks San! Very pleased to hear you have acquired a C4S, it's a cracking 996. Enjoy the journey.
@murraytappington Жыл бұрын
Brilliant - simple, helpful, honest and informative! Very much appreciated. I have a completely stock, late (2004) 996 c2 . After semi solid engine mounts I think this might be the only other thing I change. Thanks again
@hawkinsjd11 Жыл бұрын
My butt dyno really liked the IPD Plenum and upgraded throttle body on my 986 S. It made a noticeable difference in throttle response and acceleration. I also did breathing upgrades on my Boxster. Washable air filter, ipd, secondary cat delete(replaced with resonators) and a borla exhaust.
@rogerjohnson3782 жыл бұрын
You have such a tastefully modified car, you left the essence of the car but improved the experience, I wouldn't change a thing.
@9WERKSTV2 жыл бұрын
Thank you kindly!
@morphyon2 жыл бұрын
And by pure coincidence created a 996 Sport Classic :D
@gregspark98452 жыл бұрын
@@morphyon I've just bought a 997.1 aimed at that goal too. Ducktail (they work so well on 996/7), Ohlins Coilovers, 19 inch Carrera Sport wheels, Sport Chrono Plus, short shifter, bespoke re-covered steering wheel. Here: kzbin.info/www/bejne/amjNhmmVbpuZZqs
@morphyon2 жыл бұрын
@@gregspark9845 nice package 👌🏼
@kc550 Жыл бұрын
Nice gains, and engine sounds healthy. Careful with your bagless steering wheel there, you're still running the original seat belt which has a sewn segment of the belt designed to rip apart upon a crash, allowing the belt to slacken. Once that segment opens up it could mean your face meeting the steering wheel in a very violent fashion. I suggest you install a B-pillar bar with a harness instead, if you value your physical appearance lol.
@remotorcycled6 ай бұрын
Really helpful video, having bought a 996 carrera 2 last year this was going to be on the list of things to do. Thanks
@danielb5072 жыл бұрын
Your reaction to the sound of the resonator bypass: that’s journalism!
@mrh65772 жыл бұрын
The Helmholtz doesn’t restrict any air flow. The air flowing over the chamber just changes the sound. No restrictions.
@richardsholl59772 жыл бұрын
Another interesting and honest video. Thanks.
@9WERKSTV2 жыл бұрын
Thank you Richard.
@rnt45t12 жыл бұрын
You've got the life, my man. Cool car, awesome friends, and that full head of hair. I am one bald jealous fan.
@craftingmat54252 жыл бұрын
Your C2 is really looking good. I wished I could legally drive the ducktail here in Germany as well, but it looks like nearly impossible to get this done. Also I like the Fuchs-like wheels in combination with the green color. You really did a very (veeery) good job. Good luck with the engine... my C2 3,6 passed away 4 years ago with a catastrophic engine failure. Still... I am thinking about buying one again 🙂 Good content - LIKE!
@9WERKSTV2 жыл бұрын
Thanks very much!
@supersumohh Жыл бұрын
Hey there - whats the issue with the Ducktail? As it doesnt change any dimensions of the car, i dont see any problems. Bypass and Plenum would be more of an issue. I am also from germany.. No mods, just a bypass-exhaust and thinking about bypassing the resonator (guess, the exhaust is louder anyways)...
@craftingmat5425 Жыл бұрын
@@supersumohh Nunja, es ist ein Anbauteil, da braucht man eben ein ABE (kann man komplett vergessen) oder Papiere zur Eintragung. Für den 997 gibt es einen Hersteller, der das bietet (Mooshammer glaub ich), aber für den 996 gibt es nicht mal einen Hersteller, der ein Materialgutachten mitliefern würde, um es per Einzelabnahme durch zu bekommen. Klar kann man es dran bauen, aber wenn einer genau hinschaut, wird der Wagen ggf. auch stillgelegt. D eben...
@alanwayte4322 жыл бұрын
Great modification, interesting and informative as always
@9WERKSTV2 жыл бұрын
Thank you Alan.
@DonziGT230 Жыл бұрын
It would have been nice to see the plenum and K&N separately. It would also be nice to see if the resonator bypass does anything for power.
@aboyandhisdog2 жыл бұрын
Outstanding, Lee! If you ever get the chance, I would love to see the dyno test with no air filter in the mix at all. Always wondered how much a filter hinders air flow and affects HP.
@9WERKSTV2 жыл бұрын
Thanks Tom! Yes it would have been great to do a run with just the filter, next time perhaps!
@warrenlucier5796 Жыл бұрын
The filter will straighten the airflow into the throttle body and the K&N or a BMC will flow the most air.
@motorclaimguru2 жыл бұрын
in my old one, ipd plenum, throttle, dansk exhaust, k & n remap, hit 330 bhp on the dyno
@youngsyr2 жыл бұрын
What so many people fail to understand in modifying engines for power with bolt on parts is that the ECU is set up to work with the standard parts and changing parts often alters the data that the ECU uses to set the mapping of the engine. E.g. the intake plenum can alter the amount of air entrring into the engine for a given MAF reading, the ECU therefore thinks there is less air in the engine than there actually is, so the ECU injects less fuel than it normally would, resulting in a leaner burn, more power and hotter running temps! You could achieve the same results simply by remapping the ECU to run the engine leaner and not bother to fit the fancy £700 plenum. You obviously wouldn't, because you don't want the engine to run hotter though! You could have checked this by logging the AFR before and after fitting the parts. Any change in AFR would indicate that the change on power is at least partially resulting from the parts messing up the ECU'S input data, not from the part itself.
@bakerbk36962 жыл бұрын
Great video as usual, good to know the extent of the difference
@9WERKSTV2 жыл бұрын
Glad it was helpful
@pjay30282 жыл бұрын
Interesting video. It's just a shame you didn't do separate runs for the plenum and the filter.
@Carrera-gp9od2 жыл бұрын
On a good day panel filter 1-2bhp
@gregspark98452 жыл бұрын
@@Carrera-gp9od as good as zero...filters are seriously over-rated.
@Carrera-gp9od2 жыл бұрын
@@gregspark9845 Correct , those k and n are coated in oil too , can cause havoc with your mass air flow sensor. Their cold air induction kits are worse , most of them actually lose power , they sound good though .
@gregspark98452 жыл бұрын
@@Carrera-gp9od I was in an Audi group some time ago, and oil contamination of MAS was identified as a big problem with K&N filters.
@pjay30282 жыл бұрын
@@Carrera-gp9od maybe, but I've never heard of actual power increases from the IPD plenum before, either.
@GetUpFalcon2 жыл бұрын
Congratulations on the result Lee. You’ve gone about modifying your car as a grown up and avoided the gotta have this gotta have that upgrade just because. The sum total is a very desirable machine.
@9WERKSTV2 жыл бұрын
That's very kind, thank you. I seriously love that 996, it does everything I need it to and hopefully shows you don't need a £100k 911 to have a load of fun.
@charliewolf75002 жыл бұрын
My IPD Plenum was in terrible condition when first received. I think I must of been sent a factory second. The line up of the moulds, flashing and inclusions were all terrible quality. I had to machine, grind and file the IPD Plenum, to get it in reasonable shape and improve air flow. Its good to see IPD finally got there act together in terms of quality. My IPD Plenum also increased the diameter of the intake for higher volume. I can't remember the size exactly, but I think the diameter of the intake and throttle body increased by around 10mm.
@laurencegibbs36402 жыл бұрын
I have a few reservations about the validity of the test. As has been alluded to already by others . The ECU will adapt and alter fuel trims and timing . I would have like to see a pull with the original parts put back on after the ipd plenum. It might well be that the ECU simply adapted to the engine being given a rigorous workout on the Dyno. Italian tune up if you like.
@spyder_man2 жыл бұрын
Great Video Lee, sounds amazing. 👍🏻
@9WERKSTV2 жыл бұрын
Thanks 👍
@motorclaimguru2 жыл бұрын
Great vid lee, very enjoyable. You can also do a lot with exhaust tuning as well,
@713vinh2 жыл бұрын
Awesome inexpensive bolt on mods! Love where you are going with your channel.
@riddledriddler39332 жыл бұрын
are you sure about IPD being inexpensive? :D
@9WERKSTV2 жыл бұрын
Thanks Vincent!
@lifeflightunlimitedblu-deu1592 Жыл бұрын
Thanks!
@enriclibert5452 жыл бұрын
Thanks for your videos, from 🇪🇸🇪🇸🇪🇸👍🏻👍🏻👍🏻
@9WERKSTV2 жыл бұрын
Thank you Enric!
@bobbarker142 жыл бұрын
This is the second video I've seen confirming the modest gains with the IPD plenum via dyno. Vu Nguyen with PCA did a similar test and it also showed increases throughout the rev range. N=2 now and I'm considering throwing one in. I imagine if one lived in California, they would have to temporarily swap it back out for the emission inspection in order to pass visual. Seems like a pretty easy install so why not?
@thinaharran Жыл бұрын
On my 997.2 C2S, the IPD Plenum is recommended only in a stage 3 upgrade. A base tune should push it up for 400hp then onwards will need a sports header/exhaust then later the IPD. I guess by doing both it will be difficult to say the true effect of the plenum upgrade.
@thejupiter22 жыл бұрын
Thank you. I can't thank you enough.You have just saved me a small fortune. All that expense for a miserable 10 BHP gain! Utterly pointless.
@skyachtone87022 жыл бұрын
Well reported! Proper journalism!
@marcusoutdoors49999 ай бұрын
Extremely interesting. I wonder what high flow cats would do?
@chriswharrier35712 жыл бұрын
Great video, 600 quid for 10bhp. I like the look of the resonator delete thou.
@9WERKSTV2 жыл бұрын
Thanks Chris, yes the resonator delete is a good mod, highly recommended.
@chriswharrier35712 жыл бұрын
@@9WERKSTV It's about the level of my technical ability to complete.
@CarlsModsClass2 жыл бұрын
Great video lee I'm currently looking at these sort of mods for my 2003 3.2 986 boxster I've already started by fitting a Design tek Deep sound back box i'd love to know more what affect the 200 cell sports cats would have on the 3.2 M96 engine etc.
@thiosemicarbizidebenzoylal29212 жыл бұрын
You cannot change air flow without actually tuning the engine and expect gains. the plenum can be HONED for even greater unrestricted air flow for cheap, but i wouldnt do it without a full fuel air ratio tune.
@pjay30282 жыл бұрын
If the air/fuel ratios are OK with the existing map, you don't need to do anything else. As stated in the video, they checked the air/fuel ratios after the mods were installed as part of the dyno run, and they were good, so that's fine. There is always a bit of leeway in the standard maps because not all engines will breathe exactly the same vol of air.
@QFXmusic2 жыл бұрын
Great video Lee
@9WERKSTV2 жыл бұрын
Thanks 👍
@Lee-zk8vu Жыл бұрын
Need to get cat-back exhaust as well as a tune.
@sherparoyale8 ай бұрын
Love the color. What “green” is it and is original paint or after market (paint or wrap)? Thanks
@tlzangl2 жыл бұрын
Nice looking panda. Looks like a nezumi.
@9WERKSTV2 жыл бұрын
Good spot!
@thejumbo2 жыл бұрын
Great video - I have a 2000 996 that I would like to work on a bit, as well. Questions: What are the 18" Fuch-like rims, and what is the duck tail you are running? Or, is it in another video? ;)
@jacekliberak54632 жыл бұрын
I hear that the IPD plenum gives more power only when you combine it with larger (997 gt3) throttle body
@warrenlucier5796 Жыл бұрын
Correct and if you improve the intake side you will need to free up the flow on the exhaust side too and you will get the full benefit you are looking for.
@ett_baer2 жыл бұрын
Thanks for the info! BTW you look like Sean Bean!
@Carrera-gp9od2 жыл бұрын
I’m only a minute in , but I’m going to guess they will make little or no difference 😂
@alexchuo8055 Жыл бұрын
Thanks for the video. I have a 997 and installed the IPD plenum in addition to the GT3 throttle body. Was there a reason why you didn’t install that part?
@theclutch192 жыл бұрын
The K&N alone could have given you those gains... and the IPD a waste of money. As soon as you whipped out the K&N, I knew your results would be skewed. So much for proper journalism. :( thanks for the video regardless as they are well done at that.
@villaman4818 Жыл бұрын
Brilliant...many thanks. Now on my list !
@nateisright Жыл бұрын
Ditch the K&N oily filter. The stock air filters are just fine.
@icanbelievemyeyez465311 ай бұрын
Im new to Porsche… which year is your car? Thanks
@Van-tastic2 жыл бұрын
Also, you can’t test the IPD like that. The computer must be reset so that it can readjust long term fuel trims. The cable throttle ECU barely has any processing power so, it takes a lot of samples before it makes a change on the parameters it sees.
@9WERKSTV2 жыл бұрын
As we said in the video, the ECU adjusted fine.
@Van-tastic2 жыл бұрын
@@9WERKSTV the ECU ‘will’ be adjusted fine after some time driving and it has enough data to change the long term fuel trim.
@rhesaobineche27442 жыл бұрын
Thanks
@9WERKSTV2 жыл бұрын
Thank you kindly for supporting the channel, Rhesa!
@jaapthieme65612 жыл бұрын
Very interesting Lee! What were the total cost for this upgrade? Thanks!
@garage19builds Жыл бұрын
Was this with a stock exhaust? Mufflers and cats?
@blackericdenice11 ай бұрын
The 911 is just like any other n/a car. If you want to increase hp. You have to install hotter cams.
@danjo9112 жыл бұрын
Unfortunately you proved nothing by changing the filter and plenum at the same time. What was the reason for doing that?
@desmomotodesmomoto20332 жыл бұрын
Have you seen the K997 build?
@tomasis7 Жыл бұрын
supercharger?
@motorsandmeats882 жыл бұрын
Fantastic, scientific…. Love it. Do you know if a gt3 throttle body can be applied to our cable-throttle early 996’s?
@jobytapia63882 жыл бұрын
the GT3 cable throttle are as rare as hen's teeth, you'd want to do some extensive port work to take full advantage of the improved flow (if you could find it)
@Van-tastic2 жыл бұрын
Short answer, the best you can do for the cable throttle body is to get it bored by 3mm.
@motorsandmeats882 жыл бұрын
@@Van-tastic makes sense. Any trouble finding a new …. flap thing 😂 in the new larger size? I think I found the limit of my technical nomenclature. You know what I’m talking about?
@Van-tastic2 жыл бұрын
@@motorsandmeats88 a new one (butterfly valve) must be made. FVD is the easiest way. Send complete throttle body in as a core and they’ll send you a new one that is built by a race shop in Germany. There are US shops that do this mod as well but they will need to work on yours.
@motorsandmeats882 жыл бұрын
@@Van-tastic gotcha. And thanks for clarifying the butterfly valve!
@craiglizotte3622 жыл бұрын
What rear deck lid are you running? Looks great
@9WERKSTV2 жыл бұрын
Thanks, it's a carbon ducktail form RPM Technik.
@MikeKing-jy9tk Жыл бұрын
OMG the badge on the wheel really DOES turn into a swastika! I thought that was just urban myth!!
@paulos_23532 жыл бұрын
Any chance you could please give me a direct link for that helmholtz bypass kit , can't seem to find it anywhere ......
@9WERKSTV2 жыл бұрын
Hi Paul, it's in the video description for you.
@andyearl67849 ай бұрын
Today I’m going to talk about something I said I’d never never talk about (and then he said engine up grades) really thought he was going to talk about undescended testicles
@GT380man4 ай бұрын
Meanie.
@OGcottoncandyrandy2 жыл бұрын
You should NEVER used an oiled filter with a MAF sensor car. 🤦🏼♂️
@andyearl67849 ай бұрын
His
@frederickcook872 жыл бұрын
The ideas behind the ipd seems solid but they have been shown to produce zero benefit 😟
@kevinobal20422 жыл бұрын
Thanks!
@9WERKSTV2 жыл бұрын
Thank you for supporting the channel, Kevin - highly appreciated.
@karlosborn91362 жыл бұрын
Thanks
@9WERKSTV2 жыл бұрын
Karl, thanks so much for supporting my work, I really appreciate it.
@chasingautos63502 жыл бұрын
Thanks!
@9WERKSTV2 жыл бұрын
Thank you for supporting the channel, it means a lot.
@mattholloway97302 жыл бұрын
Thanks!
@9WERKSTV2 жыл бұрын
Thank you Matt, highly appreciated!
@jasonburrell52462 жыл бұрын
Thanks!
@9WERKSTV2 жыл бұрын
Thank you Jason!
@billwhitlatch9612 жыл бұрын
Thanks!
@9WERKSTV2 жыл бұрын
Thank you kindly, Bill!
@makakoaoc2 жыл бұрын
Thanks!
@9WERKSTV2 жыл бұрын
Thanks for your support, Chris!
@smallbloc2 жыл бұрын
Thanks!
@9WERKSTV2 жыл бұрын
Thanks Michael, hugely grateful for your support! 🙌🏻
@mattpearce94442 жыл бұрын
Thanks!
@9WERKSTV2 жыл бұрын
Thanks for supporting the channel, Matt - highly appreciated sir.
@mattpearce94442 жыл бұрын
@@9WERKSTV You’re welcome. Thanks for the great event at Heritige. Great turn out and nice to get out for a run in the GT3 even if the weather was a bit suspect. 👍🏻🏁