e60 5 series BST bypass passenger restraint error fix

I now sell a OEM plug with the resistor so you don't need to cut your current plug off. visit: www.roskinc.com
in this video i show you how to bypass the BST cable (battery safety terminal). all needed is a 2ohm resister to be soldered to the cable. this only works if your error is from the BST cable, if from the seat mat, it will not. but the majority of the time this error is from the BST cable. PLEASE TRY AT YOUR OWN RISK. use as guide only. please be very careful when attempting to do any electrical work. visit my site for more info roskinc.com

[@blakecole6328]

You sir are a genius! Just did mine and worked like a charm. I run a body shop, and even the parts at cost are not cheap. Not to mention if the original failed, then how long does the replacement last. Glad to have the red light off the dash, and no more warning messages!!! Anyone in question of longevity, I am writing this 20 minutes after completing the job. 2 ohm / 2 watt resistor should last for years if not decades. If it fails again, check your wiring.

[@brianevans673]

Can confirm this ALSO works on 2003-2005 Range Rover L322 (BMW era). I reset my code with the Gap IID tool. Thank you for a well produced video! The only thing I did slightly different was to cut the wire leads unequally and soldered the resistor parallel to the wires, not perpendicular like you have done. That allowed me to use a smaller piece of heat shrink and makes it more compact and easier to tuck away.

[@loveme2tmes671]

I tried this today for the first time and it worked. My solder kit was junk. Going to buy a better gun. Basically, I did this without soldering. I just wrapped the bare wires around the ends of the resisters and used electrical tape to secure the connection but I will invest in better solder and heat shrink wraps. Thanks for the great video

[@alexg8460]

LoveMe2Tmes did you have to reset it with a scanner or what did you use?

[@nelsonmelgar999]

What's the resistor that you used?

[@LDC5Too]

Just implemented this resistor change and it worked on my 2004 545i. I had the passenger restraint error message for a while, and during service at dealer for a 4-wheel alignment, I had them check root cause of error message, which turned out to be BST cable, quoted for $600 cable plus labor. So a pack of (5) 2.2 Ohm, 1/4watt resistors at radio shack costed $1.50 (I think), plus Carly Pro App ($40) for BMW with wireless ODB2 adapter (~$65) fixed it. It's been 3 weeks and so far so good, most importantly received state vehicle inspection sticker 2 weeks after clearing error.

[@mworksdesign]

What's the link to app for error override. I've seen the Bluetooth obdII part on Amazon but just want to confirm the app compatible for BMW. Thanks for any help.

[@dennisbusch4124]

Was BST the only SRS system error you had? Mine also has a seat belt tensioner error with Carly Pro.

[@JINSTASUTUBE]

problem is this introduces new error codes. the process needs lots of improvement too. there is actually no need to cut the factory wiring...ideally a plug end is needed as otherwise you ruin the wiring loom in cases this does not ressolve error (expensive mistake). its also a silly fix if you dont stipulate the repercussions, ie subsequent errors this causes and implications of them. be warned folks

[@dennisbusch4124]

I agree in that I'd rather have the connector and wire it up than cut and splice. Then can easily revert back if there's an issue. I've tried finding that connector to no avail. 02 525i

[@shez2cool]

Dennis Busch could you not just remove the resistor and solder the wire back together to the original BST cable if you had to revert to the original cable?

[@Struthunter]

2005 530i Got it from your site. Worked great. I had my mechanic clear the error code. He was very interested in what I did. I'm sending him this video and your site info. Thanks.

[@roskinc]

Struthunter thank you! Glad I was able to help!

[@Abomb-lw8ul]

Thank you sir! I own a 2006 BMW 330i e90, this same error appeared shortly after I installed a new starter, maybe the cause...maybe not, anyways - Used a 2.2ohm resistor, got it off Amazon. Used the myCarly app and plugin for diagnosing and clearing codes. The wire to cut on my model also has a black outer jacket and the inside wires are two twisted black wires; it also has the same yellow stripe on the connector as in this video. My (e90) wire bundle comes from the right side of the battery housing instead of the left side as in this video (e60) so be careful of which side of the wire you cut. Thanks again... saved me a lot of money.

[@robertsimental1469]

Abomb4141 what does the cable look like? I'm trying to do this on my bmw 330 but both cable are a black and brown twist not both black

[@Theriion]

Nice video and all. But how do you diagnose that this cable is faulty indeed? Also this cable is there for a reason so what's the worst case scenario in case of an accident with this bypass. Cable won't explode and won't cut the power from the battery but what can this cause in the event of crash? Will it catch fire or something ?

[@TasteofBlood]

You're the best! Hella e60's have this problem. I brought my car into the dealer to have the seat mat fixed and they told me after the repair that it was the bst cable that needed to be replaced.

[@roskinc]

I've heard one too many times dealers charging for mat replacement only to still have the error. Also when e60 go in for the battery cable recall they end up having the error when the dealer move the bst cable around aggressively. Thought I'd help people fix this issue cheap.

[@LastkingFisher]

Hello, I have really struggled to find a solution for 6 months on the net, and even on youtub, but you did it and not easy to find !! big thank you to you for the solution, THANK YOU THANK YOU bmw E61 2004

[@jefftruong6734]

Bruno tzr

[@alexg8460]

Did you have to reprogram ?

[@jevgenijdavydov6876]

This is the only one really useful video with great explanation

[@jhonnyarevalo7]

Another great video bro keep it up =) you made my car so much more fun with the sports mode now I'm ready to take that air bag message of my cluster

[@jakedevil8374]

brilliant video did mine today on e90 320i cost me £10 including an soldering iron=) normal cars dont have this system so no worrys

[@pirrurrashon]

Thx dude, I'll be trying this over the weekend. I had pretty much given up on this error code. Its annoying and had even thought about removing the light bulb in the cluster... Ghetto I know. Keep up the good work.

[@Tappie1982]

Thank you! this is exactly what I was looking for. works on 2004 520i.

[@mworksdesign]

This is now happening on my 2008 535i BMW, really annoying and I'm glad you have video. I have a question, you said the resistor part 👌🏾, but do you have a video tutorial on how to use the laptop to override your error. I'd like to learn that so I can use also after buying resistor

[@luisbermudez2830]

am having similar issues, can you send me the specs on that resistor. video was very informative. thxs for posting it

[@climbn110]

Once again you saved me a lot of money, Thanks!

[@sorawittoh]

I found this video relates to my problem and is helpful to me. Can you please advise me what resistor do I need to use for F10 m5?

[@bilkham]

Hey did you fix your problem? Which cable is the BTS for f10 and which one should i cut and put resistor

[@empowerd1]

Thank you. Very useful. Are airbags still active and will shoot in case of accident after these changes? Is 2 or 3 ohm OK for M57D30TU?

[@brianevans673]

The rest is the SRS system will be UNAFFECTED with this bypass. All airbags and seatbelt pretensioners will still be functional and active. 2.2 ohm 1 watt resistor (red-red-gold-gold) is what I used.

[@mohanadhala6330]

I have 2005 e60 545i and I have airbag and seats belt light on . I did same thing you did but still show me error and light on dash .

[@joe2dn]

+Mohanad Hala your ccc is bad, In had the same problem and changed the ccc, I baught one on ebay for 350

[@randywarren1276]

Do you know how to reprogram a used cluster for 2005 bmw 545i. They are telling me I have to buy new from BMW otherwise it won't match up VINs

[@alexg8460]

Is this the cable that goes to the battery? That connects to the postive side yellow and blk wire ?

[@MrDutchentre]

I did this with a 2.2 ohm resistor. It didn't work. The error would not clear. Any suggestions? HELP! Thanks

[@rafaelfernandezfernandez6997]

Thank you for all your help, I have one question... I have the Airbag and the seatbelt warning light on, I scan it and It show me the code 93ae - (rear airbag driver side).my car it is BMW e92 - 2009. This light turned on after a rear end hit me, but the thing it is, that it was a really soft hit imagine that I do not have any damage on my rear bumper so I don't understand why the light turned on??I try to reset it but it tell me that it is permanent.

[@blanco20001]

Hi, I have a 2006 750 li I have the same problem, I have just 1 question will this fix clear the error and the air bags will work properly????? I just want to make sure the air bags and seat belt will work in case of accident thx for your help and great video....

[@DoseOfBaani]

i just took mines to the bm place... they want $900 to fix the problem....and they told me its the same exact wire. 😂

[@TheRonmaio]

i will try this i bought a car yesterday and upon this video i bent down to look at mine to find that . In the past Whoever changed the battery put the battery in and because of the tight fitment from BMW they shorted the Positive from the battery onto the body of the car which is metal. I think you said something about this type of install can cause this cable to back feed. Am I correct in understanding? ont

[@lavinkeaty5878]

Hello, I have a question. The wires you cut then unplugged from the harness, mjne is different. Mine plugs right into the positive battery cable at the battery. Is this the same thing? Can I just cut those brown wires and put a 2ohmn in between? I have a picture but I can't upload it here.

[@007maka3]

Hi I found on eBay A resistor of the following kind "Resistor, metal layer, 2.2k Ohm, 1/4W 1%, 50 pcs.” Is that okay? Please answer the question Thank you 😊

[@Zizoproduction31]

This worked on my E61 Thanks bro ! Keep it up;)

[@TheMrAS93]

hello +roskinc, I wanted to know the colors of the resister you used and wanted to know if it works for BMW e61 2004 ?

[@rob8002]

If you want to undo this action (because it didn't work for me), does it matter how you reconnect the 2 black wires?

[@ajuneja5707]

BMW 530d not getting ignition on. Only airbag and seat belt lights are coming and all functions window and sunroof operating. But no ignition. What can I do

[@Yerevan87]

@roskinc Which program are you using on your mac to connect the OBD cable to and clear the error messages?

[@dexterlaundry7657]

Hi roskinc. My BMW 530i 2004, have the same problems as on video you posted. Before watch this video I already buy bypass and buy c110 on eBay to clear airbag and seatbelt light but still don't work. So I want try tha way you show on video, so do you think I need took off the bypass ? And do step by step as you did? And don't need the c110 scanner.?that light on my car 2 yrs ready, I hate see that but no choice. Thank you if u can help

[@minazsomani8468]

Hi, I have a BMW 320i Estate 2007, rear window sprang a fault. Don’t want to fix it as we don’t use rear area. But iDrive warning all the time. Can I by pass that? Thank you

[@jscons7424]

How can one bypass a front crash sensor, if you can’t find one immediately but need to solve ses light on panel

[@veezyloco3759]

What are the blue and red wires? And what are they suppose to be connected to? Mine is just hanging loose.. I dont see anywhere to plug it

[@kevinalexander8670]

Hello, with this bypass. Will the airbags now deploy? I’m curious because all I want is the restraint error to visually disappear.

[@brent1990xenon]

Where/How did you connect your mac with the car?

[@alberteinstin1136]

Hi, regarding this video, very informative, thx. I have a 2006 e60 M5, and the cable layout is different from what you show here. It appears that the BST cable going to the sensor fuse has 3 leads in it, rather than the 2 that you show. I wouldn't know which 2 out of 3 to bypass. Any suggestions? I'd be happy to provide a pic. BTW, how did you stumble on this bypass trick, and what are the side effects of doing it? much obliged. Albert

[@mohammedpatel5284]

Do you have any idea if this would work on an E87 (05 118i)?? Can't find a video specific to e87 but I have a suspicion e60 may be similar since theres some bypass solutions on ebay for e60/e87. Good video by the way. Thanks.

[@Richard-pr9tn]

Does this fix stop the air bag and restraint system from operating normally? Also, will this work on a 2006 750i with a code of 93FC? I can clear both lights, but they reappear when the car is driven the next time.

[@RevLee]

Hey I have 2002 BMW 745Li NO CRANK NO START need your help change starter check all fuse and relays,

[@DJCOOP1983]

how to install sub box without using aftermarket CD players

[@reggaeboyz21]

What's the watts of the 2 ohm resistor u used..thanks

[@danilsimble4389]

rinaldo chambers How many watts is it?

[@zterlep]

2.2ohm 2W resistor...worked for me

[@n54single]

Igor Terlep is it 2.2 ohm or 2.2k ohm or are they the same??

[@Mrizing]

Can you please help me, I have a 2004 bmw 545i and the ccc unit is completely dead. I've read online the chips inside need to be resolider on????

[@jodashpillay7018]

Hi is the wire u cut the 1 that gets connected to the front of the bts housing

[@sincityrrt301]

finally a solution. this and many other issues with my 550 have been annoying me. i appreciate these videos they're immensly helpful but the e60 is a piece of garbage, i'm even sick of their styling at this point both exterior and interior.

[@anthonytubman8696]

great video I have this problem! My question is how can I get that software for a mac computer?

[@joe2dn]

+Anthony Tubman the software is for windows only, I dont think there is a mac version

[@tylermacdonald2272]

What program did you use in order to reset the error memory? Searched impa but couldn't find anything. TIA

[@valramps1994]

Would this work for isafety and information module SGM-SIM

[@crazystang69s75]

hey buddy Nice video I will do mines in the morning, quick question on the negative terminal whats that black little wire with a plug on it do?

[@gmcguyver]

I believe the wire you are referring to is used for shipping only;

[@Del-ul6gt]

hi does this work on driver restraint error on 2016 BMW 535i? thnaks great video

[@LibertyNdihana]

Roskinc i am in trouble with my E60 2005. My iDrive is mis-behaving it switches on when it feel like it. When you start the car up it will just display the BMW logo then is switches off and on till it feels like going on. What could be the problem with it?

[@exhaustsdaily9759]

When are you making more of these. They are currently sold out on your website

[@vegask2]

Can you explain more in detail how you cleared the error in inpa? I used inpa and ncs expert to enable your aux but confused how to clear the error.

[@whim7240]

Great video! Am wondering if it works on Bmw 520i 2003? And what is the name of the program you are using to reset the airbag? @roskinc

[@chucke3305]

2009 528i blk/yellow hard wire. Will it work.😢

[@Charles_Odom17]

thanks man.. can you go to a independent shop to clear that or can you do it with a code reader.?

[@igorek11201007]

and after these actions the security system is working properly? or by turning off something?

[@gda86pl]

it won't disconnect battery in case of accident... i would worry if you got petrol... less if diesel as it is not flammable

[@denisemin6039]

Hello. I've got the same problem since 6 months. When i erase the error it appears like after 25-30 days. Could it be some wires problem or the sensor? Cause when i erase the fault im testing it like hard sitting in the passenger side, shaking the seat. And if i do the same thing like you will my airbags on in some accidents without anybody in the passenger seat?

[@t4turbo9]

What watt 2 ohm resistor did you use? I need to order one online my local electronic supply store don't carry it.

[@joshmo495]

For some reason I am unable to clear the codes, the cable connects but when I click clear codes it loads, then completes only for it not to erase the codes. I had erased codes before using the same laptop and cable on the same car. Any ideas thanks!

[@kaloyanyordanov1395]

Yo man would the airbags stil work after the resistor is placed

[@bowtawks]

Is this method applicable to all e60 model includes LCI version?

[@pixelcharlie]

Does this disabled the AIRBAG system though?

[@yahvin86]

wondering if you have ran into Dtc p0700 on these models. if so any pointers?

[@adrianuk8102]

Does driving with the warning light on affect the car or driving in anyway?

[@adnanulepa9661]

Hi Ive done this and it seemed to be good but right after someone sits on the passenger seat it showed up again Any solution? Thanks

[@Rockony]

So you fixed? How’s going

[@adnanulepa9661]

@@Rockony i trier everything and nothing helped so i quitted Couple months later i installed seats from e60 2006 ( mine is 2004 ) and deleted errors with mechanics diagnostic tool and it never showed again even i deleted it with my delphi diagnostic thousand times I still dont know how😂

[@Rockony]

@@adnanulepa9661has you try the by pass under the seat ?

[@Rockony]

Did you check your airbags are on of on ?

[@Ejzaidhilal]

hey do you have a video or set up oh how to change Amp Hr in battery using NCSexpert, 2006 330xi e90

[@VuTran-nd9oc]

will the air bag still works if you bypass this cable, if in an accident...will the air bag deploy..??

[@ABWSKITCHEN]

Do you know where is the cable on a 2013 X3?

[@vadimtornea5961]

I have the same problem on e39. Question: How do you know how many Ohms do you need?

[@anthonyvelazquez9246]

Hey how is it going I see you post some good videos of what you do when or if can you post one of bypassing to use the navigation as a DVD player

[@Bong_zoro]

I search to buy a 2 ohm resistor and I was wondering how many watts should it?

[@saransaran28]

What value do I put the resistors , i have Bmw e61 525d 2004

[@Ar836k1]

Not sure if this is the proper fix as the car will not function as designed. It will turn off the warning message which doesn't say much. In the event of a collision the battery might not get disconnected as it is supposed to, to prevent a possible fire. I would just replace the cable due to safety reasons.

[@roskinc]

Ar836k1 I always tell people to replace cable. This is just a way to test if it is the cable and not the Matt or bad battery

[@gda86pl]

you can check resistance of cable in DISA (i did not see this in INPA) with simple test. vmware with DIS is on web...

[@abumannocchi]

For e90 it goes into the negative or positive cable?

[@Da78Gemini]

Will this work with a higher resistor, like 220 omn?

[@Valdemar_Einstein]

Привет. Быстро ты с ней справился. Скажи, а подушка безопасности пассажира будет работать после этой манипуляции?

[@lauraaken1966]

Hi my 2004 e60 says restraint system fault and driver restraint fault. would this work for this

[@kennethm2v]

@roskinc after follow all the step the error 9aff dissaper but now im getting error 9b01 wiring break detonation circuit any idea???

[@vigaringarcia8472]

My question is if the computer thinks there's somebody sitting or that nobody is sitting?

first of all, you gonna have really bad time in the case of fire... and as the second, where did you get that the resistor have to be 2 ohms ?

[@borad1993]

i have a 1994 e34 525i it had original an passenger airbag, now i fitted an leather interior from another car that didnt had a passenger airbag, does anyone know if i can use a resistance like the one in the vid to make the system work again, if so, does the 2ohm resistor make the computer think that there is someone on the passengerseat. sorry for my bad english. hopefully someone can help me, thanks

[@Pasaris2008]

Hello, I have the same problem on a 525d ,I put a fuse car insteed of a resistor and is not working,I have to put a resistor of 2 ohm? Or it s have another problem? Thank you

[@roskinc]

mihalache george it HAS to be a 2ohm 1/4 watt resistor. Exactly that resistor

[@qaahm2635]

whats the name of this cable which u r bypassing coz it is missing in my car

[@padraicdevine8907]

is it the same thing for a 3 series e90 model or is there a way

[@moshazza5684]

I tried this. Bought two 1ohm resistors put them in line. But I had to wire them into the "car side" of the loom rather than disconnecting that plug as the plug was loose and error kept coming back with any movement. The reset worked with two 1ohm resistors online for couple months but error came back... and this time I couldn't even reset it. Then I tried just a 1ohm resistor on its own. It reset light went off all day but would re appear when starting car up first thing in morning. I'm at this position now where light is on. I'm next going to buy a single 2.2ohm resistor to wire in. Can anyone tell me if a high wattage or low wattage is more suitable

[@dwainbradshaw3212]

Would this work on a 2005 BMW 745Li (E65) ??

[@israelrodriguez7767]

Hey by doing this will affect anything? ,because I did it and now my car drain over night thanks in advance

[@GotaGetaGoing]

What was the module and error code that you had before and cleared?

[@rickyp8195]

Hey looks like you upgrade your monitor how did you do that just asking 👍🏽

[@MiamiJunkie]

Ricky Peralta yes! please do tell ! roskinc

[@roskinc]

It's not software upgrade I did a new Cic upgrade. Will post video very soon!

[@atproductions73]

roskinc cant wait to do the retrofit on m5! please post it quik!

[@rubble9999]

@@roskinc hey man I have a fault showing that air bag control unit faulty ..intermittent fault ..will this fix work for that

[@dwainbradshaw3212]

Can this work for 2005 BMW 745 Li ( E65 E66 ) ?

[@tford17]

Nice video. I don't see this item for sale on your site

[@MiamiJunkie]

CIC upgrade video please !!! :-)

[@derickmaldonado3350]

Can you post a video of how to update the office system please, my needs an update. Thank you..

[@vladzbtl9574]

When will the bluetooth add on module be available?

[@bigbm1888]

Will light still come on at ignition the go off again ...uk needs it to illuminate then go off

[@roskinc]

All light will appear then disappear