Like watching how you set up the twin motors out of the chassis, a lot easier to set the mesh. Having the center brace hinge up out of the way is nice.
@earlmoorhead55552 жыл бұрын
Yes
@gucciskunkit4 жыл бұрын
When most see a dead end earl just makes a u-turn and takes a higher road, i love this channel💪💪❤🔥💯
@earlmoorhead55554 жыл бұрын
Appreciate that 🙏🙏
@cmalt-z71712 жыл бұрын
Like the esc plate and ease of access with the flip up bar/brace.
@mtctookie254 жыл бұрын
You moving right along on this build, keep wrenching!
@earlmoorhead55554 жыл бұрын
Thanks 🙏
@islandrc-duke19724 жыл бұрын
awesome,getting closer to the finish line,awesome stuff
@earlmoorhead55554 жыл бұрын
Yes almost there 💯💯
@rcclan4 жыл бұрын
I have a friend who has a twin motor infraction but he's gone a different route but I think you have done a fab job m8 can't wait to see it go buddy
@earlmoorhead55554 жыл бұрын
Thanks 🙏
@streetdreamz80564 жыл бұрын
Nice work earl! Looks good
@earlmoorhead55554 жыл бұрын
Street Dreamz thanks app that 💯💯🔥🔥🔥🔥🔥
@andrewwhiting55264 жыл бұрын
Getting closer 😀can't wait to see the first shake down runs😎👍😀
@earlmoorhead55554 жыл бұрын
Andrew Whiting thanks me to 🙏👍💯🔥🔥🔥🔥
@ShadeTree_RC4 жыл бұрын
been fun watching ya build this monstrosity bro big thumbs up
@earlmoorhead55554 жыл бұрын
Thanks 🙏
@KurtsRCs4 жыл бұрын
That setup looks nice and clean can't wait to see burn up some tires 👊👍🔥💯💪🏻🙏🏁
@earlmoorhead55554 жыл бұрын
Yes should be fun 🙏💯💯🔥🔥🔥👍👍👍
@MetzRc844 жыл бұрын
DUDE. I am so excited to see the next video! It’s going to be ridiculous!!!
@earlmoorhead55554 жыл бұрын
Thanks Metz 🙏appreciate the support 💯💯💯💯
@MetzRc844 жыл бұрын
Earl Moorhead what solder gun to you use?
@earlmoorhead55554 жыл бұрын
Metz Rc weiler 100 amp solder gun from home depo 👍💯🔥🔥🔥🔥
@MetzRc844 жыл бұрын
Earl Moorhead awesome. Thank you sir
@philipjolley10154 жыл бұрын
very nice build brother. gonna be a tire killer.
@earlmoorhead55554 жыл бұрын
Yes should be fun if I can control the power curve lmao 🤣
@prozay68563 жыл бұрын
Just SUB you. I bought a new Felony, and finding information onto the different things you can do is hard to find... This twin motor setup though i will be doing! Thank you for the video
@1etergen4 жыл бұрын
TWINS are always fun to see. Looks Bitchen!! FULL SEND!
@John-np2bf Жыл бұрын
Hi Earl! I love your builds and they way you work. I'm also very jealous of the beautiful paint jobs on your cars. Nice! I actually got one of these dual motor mounts and I found that I couldn't tighten the motors down if I use a pinion that's a little bigger it blocks those screws. Can you tell me what size pinion you used on that mount? I really appreciate it. I'm trying to build a dual motor Felony. Speaking of Felony's (lol) Do you have any? I'm not talking about the law either.... 😂 Thanks Earl!!!
@earlmoorhead5555 Жыл бұрын
27 tooth and 29 tooth but took awhile to get them locked down 👍👍
@Charles1971ify4 жыл бұрын
The Madd Genius singing the Mikey Mouse club house 🎵...lol. Another great video bro.
@earlmoorhead55554 жыл бұрын
Lmao 🤣 you know 🙏💯🔥🔥🔥💪💪💪💪
@reapersrcperformance88354 жыл бұрын
Well I can't believe it but I just got another infraction , found it in a Pawnshop $175 bucks and drove straight to the hobby shop got me an ESC max5 so I'm going to build me another one lol
@reapersrcperformance88354 жыл бұрын
And the truck is brand new to top it off !!
@earlmoorhead55554 жыл бұрын
That’s awesome 😎
@earlmoorhead55554 жыл бұрын
Omar Gomez great deal for sure 💯💯🔥🔥🔥
@bwells27104 жыл бұрын
Going to be such a clean build!.. I'm glad you went with the ESC's laid down. When you solder you don't do any pre-tinning?
@earlmoorhead55554 жыл бұрын
Yes I do Pre tin my soldering I also use flux on the tip on the gun as well 🙏💯🔥🔥🔥🔥
@Lunarpollo56222 жыл бұрын
Question, say for example I had a dual esc setup, wire both my ESCs through a y harness and I lift the red wire out of one of them. If i chose to switch off the master esc (the one that still has it's red wire) what will happen to the slave? (the esc that doesn't have it's red wire) Will the slave work perfectly on it's own? Master powers two motors and the slave powers one, both escs Are operating from the same battery
@jessekormick37962 жыл бұрын
I got a 1717 in my infraction. What ⚙️ gearing do u recommend? Almost done with build. Thanks too your channel I've learned a lot!! Thanks Earl u rock🤟💯
@andrewfarniok93542 жыл бұрын
Saw something you did and thought I’d share to maybe help people or a cheaper way of doing things… with the grub screw problem you could just sand or cut a little off the grub screw rather than risking damaging the shaft… no hate just a little tip id do different🤟
@Bassin07Si4 жыл бұрын
Can't wait to see this monster ripping
@earlmoorhead55554 жыл бұрын
Yes should be fun for sure 👍👍👍
@ronniecreason78704 жыл бұрын
Nice job
@earlmoorhead55554 жыл бұрын
Thanks 🙏
@mosests34 жыл бұрын
Completely awesome 👌
@earlmoorhead55554 жыл бұрын
Thanks 🙏
@smrdmr13 жыл бұрын
Wow... Insane! Now I have to try this. What micro torch are you using? I've tried several different ones and they seem to fail really fast. Looking for one that actually works long enough to have to refill.
@reapersrcperformance88354 жыл бұрын
Starting to get character !!!
@earlmoorhead55554 жыл бұрын
Yes it’s starting to show it’s colors for sure 💯💯💯
@reapersrcperformance88354 жыл бұрын
If your using the original center shafts or the 6mm shafts they won't work you will need the 8mm ones for they won't boow in there slot
@earlmoorhead55554 жыл бұрын
Ya I figure they won’t hind to much but I did change the pins to harden steel hopefully they hold 🙏💯🔥🔥🔥🔥
@reapersrcperformance88354 жыл бұрын
@@earlmoorhead5555 I I meant the center dog bones you need to upgrade to 8mm cause they won't hold ??
@reapersrcperformance88354 жыл бұрын
@@earlmoorhead5555 the first hit I did they shot up into the
@ggsupplies3102 жыл бұрын
What pinion sizes would you recommend starting off playing with and spur sizes on a dual motor for drag?
@earlmoorhead55552 жыл бұрын
47 spur
@TurtleRc Жыл бұрын
The loctite 424 is 495 in the states ya know
@earlmoorhead5555 Жыл бұрын
Good to know
@vlratcliffe13 жыл бұрын
Hi amazingly cool .lay out why do you have twin esc one it run on single esc .as the motors are going one way why do you need two esc .plz can you tell me thanks
@earlmoorhead55553 жыл бұрын
You can’t wire two motors to 1 esc as the magnet are in different positions when the stop so it would back feed and short the esc on the first few trigger pulls 👍👍
@vlratcliffe13 жыл бұрын
@@earlmoorhead5555 ok thanks didnt know that
@arrmaboy_65083 жыл бұрын
If im putting a 1717kv castle in do i need to switch the motor around
@earlmoorhead55553 жыл бұрын
No it fit in the stock location 👍👍👍
@user-bv8gh1rn9c3 жыл бұрын
My friend, I have a question: where did you put the first esc wire in any channel and the second esc into any channel, the first servo in any channel, and the second servo in any channel
@brianargo93064 жыл бұрын
I just came across this guy check him out and maybe this company for driveshaft for ur Summit Markus Dimitri on KZbin. Here's the company name for the driveshafts GMP Racing. Good luck! Hope they have what u need
@earlmoorhead55554 жыл бұрын
Ok I’ll check now 💯💯👍👍🙏🙏
@jameswisecarver Жыл бұрын
I think someone is gettin they butt tore up in the background!
@jamesgeorge6094 жыл бұрын
Don’t you have to program the rotation of the motors?
@earlmoorhead55554 жыл бұрын
Yes just make sure both motors are connected ABC marks are the same on both esc and motors then it can be programmed if needed 🙏💯🔥🔥🔥🔥
@dana27504 жыл бұрын
You will definitely need to have one of them reversed. Make sure to recalibrate your esc after you reverse the motor or you may not get full throttle out of that motor. This will cause the other motor to work harder and most likely run hotter.
@earlmoorhead55554 жыл бұрын
Dana T both motors are on the same side so they should spin the same direction one will pull up on the spur and one will push down on the other side since I have the wire connected the same way on the esc if I flipped one motor around I would need to reverse it correct or am I missing something ??
@dana27504 жыл бұрын
Earl Moorhead you are correct I was overthinking your setup. Good luck can’t wait to see it run
@earlmoorhead55554 жыл бұрын
I was rethinking it for awhile lol after you said reverse one took me a minute to realize I was ok 😂😂💯🔥🔥🔥🔥
@The84294 жыл бұрын
Don’t drill through your table lol
@earlmoorhead55554 жыл бұрын
No I won’t lol 😂
@reapersrcperformance88354 жыл бұрын
Also you will need some special connector's call me