Early 6.0 HPOP....Fixing another shops FAIL

[@packingbone1953]

Closing in on 10k subs nice! By far my favorite diesel channel

[@AutomedicGarage]

Thanks bud that means alot

[@chaseo7542]

Ffg

[@toomanytoys]

This had the first generation '03-'04 cover on it; there are three versions. You can see a hint of light contact of the J-tube to the cover at 10:05. The Gen 2 cover was ground at the cover's manufacturer in that area for a little more clearance, and Gen 3 was for the '04 with the change in pump and rails. They are cast with a hump to clear the tube for that model's tube.

[@AutomedicGarage]

I actually didn’t know there was a change in the early style pump cover thanks.

[@johncraig406]

I have an '02 7.3L but I really enjoy watching your Channel. just wish you were closer to Tulsa, OK so far, my '02 Excursion has not needed any engine work, just had the AC fixed this week, and all of the body mount bushings replaced, except for the Sway Bar, that thing is a bear, and the rubber bushings in it are still good.

[@michaeljanssen5089]

Once again, another extremely well done, professional video, and job. Drew, you are a master of your craft. As I’ve said before, I will haul my ass all the way to Tennessee to have you work on my rig should the need ever arise, and I do have a funny feeling my head gaskets are on the way out! Keep up the great work, as it is always a pleasure to watch you work. Be well!

[@michaeljanssen5089]

I always enjoy your videos. You do a fine job of explaining things, without all the damn dogs barking and loud music in the background like so many other peoples’ videos. You take your work seriously and it shows. The way I see it, if you’re going to take the time to make a video ( and I can only imagine how much time actually goes into making a proper video, with editing and all that) then do it like you actually mean to help a fellow out. Thank you, and know that you’re appreciated by us followers who aim to keep our rigs on the road, and keep ‘em going PROPERLY.

[@revolutionanarchy713]

I'm pretty sure I have a hpop to do as well, in my 2003 f350 6.0 dually. This video will be handy in the near future, and thank you for that!

[@AgapeLoveAutomotive]

Y’all do exceptional work 👍 The ONLY thing I would recommend doing differently is your choice of pump on the 03 and 04 trucks. If the customer needs a truck back yesterday, then please use the Motorcraft pump. If the customer can give you a couple days, then I recommend them spending the money on the Dieselsite pump. I’ve installed and supported quite a few of them and have yet to have an issue where the problem is the pump. Phenomenal job diagnosing that truck regardless 👍

[@geraldhawkins2643]

Dam another awesome video!!! Nice work my friend

[@briansnik1848]

Awesome job man. Good videos brother. Just did mine. Cleaning stuff for days!

[@timezone4907]

I spent over $10k on my 07 got scammed. Wish I knew about you 3yrs ago. I will bring you mine if you would like to do a video on it

[@nelmor29]

Awesome work brother. Thank you so much for your videos. Very helpful

[@AutomedicGarage]

Sure thing. Thanks for watching.

[@victorcastrejon6679]

I am really enjoying the content, please keep it up.

[@sveinhaland2975]

Great job!!

[@travis1572]

Great job

[@harrelthomas9232]

Thank you oh so much lady !

[@ryanrichard9342]

Nice job. 👍🏼

[@NeedaRez]

I have a 2004, leaf spring front end truck, with the cast hpo rail, icp front pass. rocker cover. Im building just shy of 300psi hpo, so no start at all. I replaced the stand pipe and dummy plugs, while there i noticed my ball cups were a bit loose. I dont have a way to air test. Im confused on what hpop i need, how can i tell between the two covers? Also, going to check my lpop relief tomorrow

[@FishinwithSquirrel]

Which hpop do you recommend? I’ve seen you use adrenaline and Bosch. Thanks, your videos are extremely helpful!🐿

[@AutomedicGarage]

@@FishinwithSquirrel motorcraft is best replacement, Bosch 2nd, adrenaline if your looking for better hpop numbers

[@FishinwithSquirrel]

@ thank you!

[@fsb_-bf3th]

Hell yeah! Sub’d.

[@Benjamin-oy9fj]

I have an 03 6.0 customer pay international to do a diagnostic on, and they told him it is pushing oil to the fuel bowl, to check injectors o rings, and the customer bought the o rings ,I removed all of the injectors they all looks good esept # 2 injector white o ring swollen but not cut the only diferent I spotted all of the injectors had some white under all of the white o rings I'm wandering if they're some cracked injectors cups. Engine starts with starter fluid for 15 minutes then wouldn't start again til it got cold again if you have any idea what could be I appreciate a tip.. I will help you with something. This engine was put in two years ago rebuild.

[@AutomedicGarage]

@@Benjamin-oy9fj 6.0s don’t typically have injector cup issues, hope you haven’t damaged any pistons or rods by using the starting fluid, it’s way to volatile and ignites early making it prone to crack a piston or bend a rod. If your saying it runs for 15 mins then won’t crank back up till it cools off it’s more than likely a crank no start hot due to a Hpo leak. Being it’s an 03 with the early style round pump I would bet it’s the pump or j tube orings. Injectors probably shouldn’t have been messed with and sounds like the shop didn’t know how to diagnose either. What’s your live data for icp psi, ipr %, FICM main power, FICM sync and fuel pressure on a manual gauge when problem happens?

[@edgardoenikrodriguez9854]

Hello, I follow you, I see that you do good work. I have a problem with a 2004 f250, I have a swap of 06 engine with 06 harness and the computer does not read the ficum, it works poorly, what can I do?

[@AutomedicGarage]

Are you saying your pcm doesn’t communicate with the FICM or your scan tool doesn’t?

[@edgardoenikrodriguez9854]

@@AutomedicGarage The scanner says connection failed.

[@patrickwelch620]

@@edgardoenikrodriguez9854 try the cigarette lighter. I think they share the same fuse. Just an idea.

[@dustinmoore5335]

I have an issue 2003 f350 6.0. Icp pressure at 550 wont fire. It tries but wont fire. Replaced icp and ipr. No joy. Tested the ficm and did hp oil leak check no leaks found. Idk where to go from here. Im debating doing the hpop but idk the pressures dont act like its a hpop. If yall have any advice please share some knowledge Thank you

[@AutomedicGarage]

@@dustinmoore5335 what’s your fuel pressure?

[@dustinmoore5335]

@AutomedicGarage idk what the fuel pressure is, I took the fuel filter cap off and cycled the pump and I was getting fuel into the filter quickly. Seemed like everything was working correctly. When I did the oil leak test I tried at the ipr and icp locations and forced on the ipr during the test no noticeable leaks. Should I be looking at a fuel issue?

[@dustinmoore5335]

@@AutomedicGarage i was debating pulling the turbo to see if the j tube is leaking

[@AutomedicGarage]

@@dustinmoore5335 gotta check fuel pressure and if your hearing air leaks there’s a issue. Is it crank no start?

[@dustinmoore5335]

@AutomedicGarage i hear air just no were i can see it. I pulled valve covers and can't see if there is a leak. It is a no crank no start

[@brucestovall874]

Where are your shop located in what state

[@Andrew-ju4be]

Are the bostech rebuilt pumps any good as new or just go with the brand new?

[@camerondeter2524]

Where you located I think the shop did the same thing that happened to them had high pressure oil pump done 2 months ago now it runs when cold but as soon as it gets to running temp it dies

[@AutomedicGarage]

@@camerondeter2524 did they replace the J tube also? What brand pump did they use?

[@outdoorsadrenaline]

Nice work! What’s a job like this typically cost?

[@AutomedicGarage]

$800 labor plus parts.

[@outdoorsadrenaline]

Thanks for getting back to me! My 03 6.0 died last weekend 150 miles from the house . Was gonna cost me 1k cheapest I could find to get it towed to the house so I had it towed to a shop. They said HPOP leak , 2k to replace seals if pump bad 3K. Trucks got 195k miles on it and in shop now. What’s a man to do. I told them to replace seals if that’s all it needed figured I could replace pump myself later if needed however after watching this video I think I’d be better off long term to have them replace that pump but money don’t come free around here. Dadgum.

[@AutomedicGarage]

@@outdoorsadrenaline replace the pump, they get weak on the early 6.0s

[@DanielGonzalezkyv]

@@AutomedicGarageare there better options than the factory hpop or they are all the same. I ve seen videos where they supposedly install a higher pressure one to feed larger injectors . Thanks in advance hope you can answer

[@AutomedicGarage]

@@DanielGonzalezkyv diesel site adrenaline pump has 2 different versions, heavy duty and performance supposed to be a better more reliable design but I’ve never ran one personally

[@davidward6741]

Did u fix the freon leak or just bandaid it by adding more?

[@AutomedicGarage]

@@davidward6741 from what I remember we topped it off, she had pretty tight budget constraints.

[@stroken_7.3_the_legend]

You need to put a updated cover on it. You will never get the overing to stop fretting. Hardly any of the big volume shops know this.

[@AutomedicGarage]

That cover was updated and had been clearanced

[@stroken_7.3_the_legend]

That 1 you pulled off was not. ​@@AutomedicGarage

[@AutomedicGarage]

@@stroken_7.3_the_legend dude I work on so many trucks I didn’t even remember which video this was, that was over a year ago and you are correct it was not a updated. I had to go through the video to remember what was going on. She was on a tight budget, single mom and I remember saying that we needed to order a new cover and explained why and she didn’t want to spend anymore money. It was pulling teeth to get the parts that we did.

[@stroken_7.3_the_legend]

@@AutomedicGarage That was a jab at the previous shop that just couldn't get it right.

[@tinok.8149]

Man im not sure if my hpop is bad on my early 03 … it feels like its holding back when under full throttle my fuel press drops to 46 psi lowest i ‘ve seen it.. then it goes up to 58ish. I changed both fuel filters no mods. Im thinking my hpop is not putting out what its supposed to . I did a pressure test on the icp port.. i dont hear any leaks. I recorded a vid with my laptop and running forscan.. o dont know how to dm message you maybe you can help? I pulled out the bottom T60 bolt no debris there. I put a new drain valve in my oil filter bowl ford part so im getting oil there.

[@AutomedicGarage]

@@tinok.8149 contact info is on our website

[@tinok.8149]

@@AutomedicGarage Hey man i found my problem!!! J-Tube had poped off the push to connect at the branch tube. No matter what i do . .. J -tube does not want to line up. I bought another J-tube off ebay … same problem .. it does NOT LINE UP! Am i doing something wrong? Early 2003! Thank you!

[@AutomedicGarage]

@@tinok.8149 never had this problem

[@tinok.8149]

@@AutomedicGarage it is strange for sure. I thought it was a bad HPOP untill i found that the J branch tube had popped off the push to connect fitting. I was getting 945psi so it was good enough to start and run but pedal to the metal was falling flat on its face. Im sure the pump is good. I just have to find a way to make sure it does not pop off again. That was my problem for sure. Early 2003s had these issues i guess. Either way thank you very much for all your help. Keep making great videos!

[@AutomedicGarage]

@@tinok.8149 sure thing bud

[@elTiterit18]

Hey wat app or site u use to read al the sensors

[@AutomedicGarage]

@@elTiterit18 autoenginuity

[@geotracker30]

is the tool for the discharge tube required to remove it?

[@AutomedicGarage]

Yes but you can make your own

[@TimothyBoyd-py9gk]

You are the Diesel Guy, You know your sh##

[@mikeches7992]

What if you drop yellow ,,o,, ring down..?

[@AutomedicGarage]

@@mikeches7992 it really shouldnt be a problem but it could stop up something in the hpop system

[@mikeches7992]

@@AutomedicGarage doesn't it fall all the way down to the oil pan?

[@mikeches7992]

How do you check a new HPOP FOR LEAKS? The old one appeared to have better suction, new ,,BOSCH,, doesnt do it...where could be the most leak the pump itself or the ,,J,,tube?

[@AutomedicGarage]

@@mikeches7992 give it a air test. I replace the j tube every time

[@mikeches7992]

@@AutomedicGarage and what should I expect from an air test? If I plug the whole on top of the pump and sent air through the whole on the buttom should the air leak through the shaft which holds the gear?

[@allen3272]

I have a 04 6.0 f250 right now it's a mess from different tech threw parts at it. 8 new injectors all kinds of sensors. O ring pieces in oil check valves both sides has no hpop at all. I noticed oil in the fuel also. I'm pretty sure it's rottella in fuel bowl. Guy must be an idiot put all that money into it they had to tow it to me. What the hell is wrong with ppl.

[@AutomedicGarage]

@@allen3272 I ask myself this almost daily. Bubba just got a 7.3 in the same shape that mechanics turned into a shit show.

[@nuffsaid6807]

Ok. I have a 8/03 manufactured truck. I cant find anything on the stand pipes removal and install

[@AutomedicGarage]

I’ve never had to replace the early style standpipes. Better design than the late model

[@tedricksimmons1561]

Where are you located?

[@AutomedicGarage]

@@tedricksimmons1561 Arlington tn

[@tedricksimmons1561]

@AutomedicGarage ok I got a 6.0 that needs your touch

[@AutomedicGarage]

@@tedricksimmons1561 I’m your huckleberry