Eastonmade; NEW Axis SHO "Super High Output" Vertical Splitter

Check out the all new Axis SHO Super High Output vertical Splitter!
Adjustable 3 second cycle time, 23hp EFI vanguard engine, front mounted controls, triple section high pressure hydraulic pump, swiveling conveyor, oil cooler and much more!
613-812-3213
www.eastonmadewoodsplitters.com
Thanks for all the feedback and support folks. It's very much appreciated. It's great that we are building such a strong community around our products where everyone can share their ideas and thoughts. Hit the like and SUBSCRIBE button if you haven't done so yet and I'll keep you in tune with what's going on in the firewood industry. Hope to see you all on the next one!!!
Give us a call for more information!!!
613-812-3213 Log Splitter Sales/Service
Check out these awesome KZbin Channels!!!
Like our videos? Check these guys out!!!! If I missed you and you want your channel on the list drop a comment below and I'll add it on the next video.
Eastonmade Ultra
Glenn @oldschoolmillenial / oldschoolmillennial
Chris @inthewoodyard / inthewoodyard
Joe @joesfirewoodvideos / joesfirewoodvideosii
justin @lifesapprentice / @lifes_apprentice
Eastonmade Axis
Buckin billy @buckinbillyray / buckinbillyraysmith
Joe @ohiowoodburner / @ohiowoodburner
Adam @hometownacres / hometownacres
mike @KNLfirewood / @knlfirewood
Gord @gpoutdoors / gpoutdoors
Dan @armsfamilyhomestead / @armsfamilyhomestead
Brittany and Francis @BandFFirewood / @bfoutdooradventures
Neil @neilkochdigdriveDIY / @digdrivediy
Eastonmade 5-11
Gord @GPoutdoors / gpoutdoors
Eastonmade 9-16
Ben @survivingcountrylife / @survivingcountrylife7069
Paul @williamsonridgeoutdoors / williamsonridgeoutdoors
Eastonmade 12-22
Harry @thedriftlesshomestead / thedriftlesshomestead
Chuck and Deb @ironandoaksawmill / ironoaksawmill
Brade @savagefirewood / @savagefirewood
Reuben @earthandbloom / @earthandbloom
Todd @struckacordfirewood / @toddpac1
Eastonmade 22-28
Gord @GPoutdoors / gpoutdoors
Doug @offgridwithdougandstacy www.youtube.co...
Eastonmade 22MB
Chris @inthewoodyard / inthewoodyard
Eastonmade 48C
Kevin @skidderkev / skidderkev
HTTPS://www.eastonmade...
#Logsplitter #firewood #logging #treecare #arborist #chainsaw #sawmill #forestry #homesteading #offgrid #heavyequipment #firewoodprocessor #logger

[@obxkoastie8170]

Andrew...Glad to see you recognized idle-down control needs to be lengthened. That 4-second time will destroy that engine constantly going from idle to full RPM as frequently as it is. I'd suggest 2-3 minutes for when a guy/gal goes to get/load more wood. Just my humble opinion as an engineer!

[@sandypidgeon4343]

yep, agreed...might want to lengthen it to 2 minutes at least. That said, wow, is that fast! GOD Bless

[@bretheinlein2879]

Nailed it on the intro music!! Perfect!! 😅

[@EastonmadeWoodSplitters]

It took a couple of trys and it and we kept coming up with different ideas aaaarggghhh arrrrggghhhj arrrrrgghhhhh lol

[@kevinware4476]

AWESOME! "MAXIS" new name

[@Redneckmfg]

You took my Name !!!! LOL That was my first thought --- Maxis ---.. Smart minds think alike !!!

[@AllenFamilyFirewood]

Ow heck ya , now that’s a real vertical splitter boys an girls . Definitely has all the bells and whistles and looks good doing it . That machine will be a game changer for anyone wanting to do production bundle grade wood . Look forward to seeing this in person at the show .

[@williamklein6649]

Phil I seen the speed of this machine and thought of buster with a conveyor. Right up your alley. Peace

[@AllenFamilyFirewood]

@@williamklein6649 Sure is William looks to be right on point with ole buster speed wise but it sure has a lot of features that buster don’t . I really like the auto idle down for saving gas and who don’t like a nice paint job . They really did a nice job on this new axis and took vertical splitting to a new level .

[@leonardberryhill4166]

@@AllenFamilyFirewood Phil you need to show them how to run this splitter.

[@FredFlintstone21]

Going from my 25 ton countyline splitter to this beast would be ABOUT the same as when i go from my 1981 volkswagen rabbit diesel, to my 2013 chevrolet corvette grandsport! What an amazing piece of equipment Andrew!

[@sawingwithsandy]

I’ve said it before but I’ll say it again, the constant innovation at Eastonmade really is impressive! Great looking splitter Andrew!

[@TheHobbyShop1]

Axis tomahawk is what I’d call it. That thing is an all out savage!! You guys nailed it as usual. 👊🏼

[@Brad-ky8to]

I’m in the market for a wood splitter. Love everything about this machine EXCEPT the 4 second engine idle down aspect. I want the full power for use all the time. A good example is when Andrew was operating the log lift and the engine had reduced itself to idle; the RPM’s need to be high for the hydraulics to do the work. Not a fan of having to wake the machine up. I can’t see the concept of rpm reduction consistently adjusting from low to high providing significant fuel usage reduction and engine wear. Otherwise the new machine looks like a winner! Another great product from Eastonmade. Congrats Andrew.

[@EastonmadeWoodSplitters]

We are going to work on it a little more to extend it. Its pretty easy to disconnet also. Just need to unplug one connector and then its all manual

[@Wild_Bill57]

Personally, the “AXIS SHO” works for a name in my book. It fits in with the SHO label for muscle cars, has that ring of familiarity. Nice improvements, BTW!

[@DaveDunehew-e1f]

That’s an awesome splitter. The idle adjustment needs tweaking but over all it’s impressive. TY for sharing your video. Dave D. from Maine.

[@aldredske6197]

Hi Andrew!!😀😀 You have got yourself a real machine there now. I'm glad you realized that the idle delay needs to be quite a bit longer. Probably between 10 to 15 seconds. Otherwise someone is going to get hurt racing the idle down. Take care my friend!!😀😀👍👍 Logger Al

[@EastonmadeWoodSplitters]

Thanks al. Always great hearing from you

[@bullybluecoal1831]

Was going to suggest Axis Extreme but, after reading some comments...... I second the Maxis.

[@Growing-Our-Retirement]

Love it, The Axis Ultimate! Not a fan of the 4 second go to idle feature. That would drive me nuts!

[@thomasworatschka6860]

Eastonmade axis sho. Put a keypad on the axis with buttons and punch in the time you want for the idle down and hit enter

[@Woodman_Custom_Sawing]

I think 15 seconds delay before idle would serve you fine. Just make it easy for the owner to adjust. I just know some people won't want it at all and some will. But I think if you time however long it takes for the wood to travel up the conveyor that would be a good starting point for the delay. Nice idea.

[@jamesjenkins6775]

Axis Lightening , that splitter looks awesome

[@oakrunacres2564]

AXILLA! What a beast. Just amazing as usual. Dave

[@ethanpemberton9011]

The home improvement intro was awesome.

[@WellsFirewood]

"Axis 2.0" Nice upgrades!!

[@michaelmiller8914]

The speed of that machine is insane.... the idel down being adjustable sounds like the icing in the cake! Adding the idel up function to more than the foot pedal would be great also.

[@dingbatjack1234]

From a guy who owns a slow cycle splitter(not EM) it’s ALL about cycle time. Glad you keep pushing the boundaries on that

[@Timberjack.loggers]

I seen one of these in actions in one Buckin Billy video there an amazing machine very impressive is there anywhere in Nova Scotia to buy them only out that way . Thanks for giving one to Buckin you sound like a great guy !

[@FireStartersPremiumFirewood]

Wow!! What a difference 2 weeks can make. Obviously a few kinks to work out but the auto idle down idea is awesome. Like everyone is saying though, it probably needs to be 10-15 seconds or so. User adjustable would be even better. The cycle time is unreal, I like the idea of the speed being user adjustable on that as well. That is pretty fast for a noob that hasn't learned all the ins and outs of rounds with cuts that aren't parallel yet. Having all of the controls on the front of the machine is freaking awesome. It sure is going to make it easier to sell one while doing a demonstration when you can have a casual conversation with a potential buyer when the machine is at idle or shut down. How's that Black Crows song go.... Jealous, jealous again! 🤩

[@jasonracette6143]

Wow, what a great machine. I'm really impressed. I'd suggest the following a name for the splitter, MOAVS - Mother of All Vertical Splitters. Keep up the great work!

[@thebatjake]

love mine still but add a boat winch on the log lift. Sucks trying to pin the lift yourself (always have to pin and unpin when transporting down the road. Other huge thing ill add is u guys should try and make some kind of a rougher top on the things. U guys up in the big woods have to nice trees but us slums lords in the lower 48 have big nasty gnarly trees and the wood flys out at you when you not looking. I have been messing with some stuff hoping to dial it in better, but a table top that doesn't let the logs slide around but catches it when force is applied is key!! Might be stupid but it helped me. Adding a fold drop leg on the tongue inside of using one or both of the side ones is much easier and seems more correct. Keep on EM, much love from Wisconsin.

[@jamesminard1867]

Axis plus is what it should be called You nailed it again Sir

[@martyr787ro5]

When at idle have the log lifter run the motor at half throttle when activated. Great machine. I think you have a winner. Thanks to Timber Wolf 17VS 😄

[@fralin1966]

The BEST keeps getting BETTER !! This is a awesome UPgrade

[@cliffjenkins6419]

Love that extra speed and control! Great idea the traversing conveyor and the auto reduction to idle. Save fuel and extend engine life. You've done it again Easton made. Cheers from HB NZ

[@WilleysFirewood]

That is a really nice unit. You guys are pushing the firewood industry into a direction it has needed to go for quite some time. Bravo!!

[@jessejones9830]

Hello from East TN found your channel,but follow your products,you stay on top of it,i cant wait to get a ultra in a couple years, call it the Axle,or Axle 1.0. lol

[@justing6594]

Home improvement. The best TV show ever!

[@GPOutdoors]

Got to have the new one - I love the AXIS - hands down. This Splitter is, in my experience, the BEST splitter on the market. Period. Mic drop....LOL!

[@OntarioFirewoodResource]

The BIG SHO!

[@Retiredoutdooroldguy]

Andrew, quite the machine hoping to get one soon. Only a wood enthusiast so trying to justify it. But it is quite thd wood terminator. Keep up the great work. Earl

[@marcelw223]

Ultimate Axis ? Very impressive guys, two thumbs up! 👍👍

[@toddsoutsideagain]

Yeah baby! It’s now the perfect splitter!! Best of both!! The new EASTONRIDGE!!😂 Good one Andrew 👊🏻…… love that new decal👏🏻

[@TheIndependentTinker]

Great improvements Eastonmade team! I have a few names to suggest: 1) 23V-Triple P with A/C 2) Add a seat and call it Sit 'n Split 3) Cord'nator

[@DaveUrner-kw9ps]

I bought an Axis. It delivered almost two weeks ago. It shipped with the conveyor detached. That means I must attach the conveyor to the work table. I looked for instructions that would show a picture or two plus some written instructions. I think it is assumed that everyone purchasing an Axis has equipment to position this beast of a conveyor to be attached to the work table. Not so. My helper and I attempted to align the end of the conveyor to the end of the work table. We would get it to almost an inch from alignment but two tringler pieces that needed to go under the swivel plate would not go under unless I lifted the conveyor up in the air so as for those two tringler pieces to go under the plate, letting alignment of channels for a shaft to be driven through. The two of us could not lift it sufficiently high enough to get alignment. Before I tell you what I did, I would like to hear direct from the horses mouth the recommended procedure for attaching the conveyor to the splitter. May I suggest that the procedure be included in the manual. Tomorrow the splitter will get its grand beginning splitting tons of rounds. Been waiting a long time for a splitter that takes the work out of bundling firewood. Thanks Eastonmade and your excellent team of innovators.

[@highwayhydroponics5823]

Idle down would drive me nuts.

[@rogerl8488]

WOW NOW THIS A HOME RUN Andrew!!! I like Axis 2.0!! An so on..

[@CodyH88]

Man Andrew, a lot of feedback on video. This is the most comments I've seen in awhile, so clearly people are excited! Other than having a 15 second standard idle down time with a 30 and maybe 45 second as options, which I know you're aware of, I would say your set. Anything beyond 45 seconds and there's no point in having the idle down feature, IMO. Name wise, I would throw in AXIS Deluxe. But I have seen AXIS+ by several others and that's solid too. Or keeping the name you have now. No sense in getting carried away with the name or making it sound like it's a totally different, redesigned machine.

[@bythebay72]

Can't wait to see this vertical beast live in Burlington. Nice work Andrew, Kenny and team

[@kendriedger151]

Yah nice machine ! That 3 or 4 second idle down would drive me nuts... id like to see it adjustable or maybe 10 to 15 second delay if its not adjustable !😊

[@danielbenedict9236]

That intro music was perfect and you totally need to name it the Binford edition Axis!

[@obiorah1]

Nice Modification on the Axis SHO Andrew you and your team are producing good quality Equipment,

[@HometownAcres]

Holy hell that thing is fast

[@EastonmadeWoodSplitters]

Its quick for sure

[@OutsidewithScheib]

This is awesome I love the idle down feature and the speed is incredible great job guys.

[@EverythingElliott]

Love the auto throttle! That’d be great on the horizontal machines when you have to walk away to load the log lift

[@welderman1221]

LOVE the idle down option.

[@danshouseofsmokeandoutdoor7119]

Buster 2.0 watch your thumbs 👍🏻

[@AllenFamilyFirewood]

lol needs one of them red circle stickers with a red line threw it and a thumb in the middle .

[@carysmith9039]

Sweet machine super fast😊 Guys always want More power ,faster you have to love it you deliver good job 😊

[@shotlifffamilyfirewood]

Man I thought pretty highly of the axis before but what a machine you have now! love the auto idle feature that will save a ton of fuel over the life of the machine. and I saw the Maxis name on another comment and I vote for that.

[@ryanwhitten4059]

Buckin sent me!!

[@michaeljheinz3336]

"The Axis Supreme" looks awesome.

[@trentwatts4913]

Awesome machine!! What kind of wood is most of that your splitting there?

[@peterbeynon2217]

I would call it the Kick Axis

[@smorefirewood]

Busters Brother. I love the auto idle throttle. 6-8 seconds would be a bit better. But that is a preference matter.

[@EastonmadeWoodSplitters]

We have plans to extend it. Are you coming out this weekend?

[@cecilwells-tm4ss]

busters sister

[@smorefirewood]

@@EastonmadeWoodSplitters Yes and I have a 2” ball on the truck. 😉😉 Phil is there with his dump trailer from delivering the Split Force to the show. 😉😉 Just saying.

[@MicahHughes-zv5zx]

@smorefirewood can’t help but notice the dead-silence to this comment 😂

[@smorefirewood]

@@MicahHughes-zv5zx it happens. It’s like a mic drop. It’s the Eastonmade Buster buster.

[@JoesFirewoodVideos]

I got to try one out at the Hoosier Firewood Hysteria, what an amazing machine!

[@EastonmadeWoodSplitters]

They work really great

[@LetThemGrow]

Think that auto-idle delay needs to be lengthened…

[@EastonmadeWoodSplitters]

Yes it does. Going to play around with it some more we may or may not be able to get it to work well

[@tstep522]

If that is 4 seconds, I would bet you end up in the 30 second range for the final design. I would only want it idling down when I am loading the log lift. That EFI engine sounds great, though!

[@toddsoutsideagain]

Wow!! I just had the chance to run an axis for the first time at the Hoosier Firewood Hysteria. It seems that most people were gathering around the two vertical power houses. So needless to say there was a lot of talk comparing. You just went and stepped it up and addressed any issue that people had with your Axis. Especially the forward controls! Well done, sir! AXIS XPC……..oh and does the new version come with two guys to load rounds at that price too😂

[@reganmcconnell6152]

The Canadian "Kickin Axis"

[@OneEyeCustoms]

The new “Axis Hatchet SHO” It’s as fast as swing a hatchet! I love the upgrades! If you ever need that machine to be in videos at my house, just say the word!! 😊

[@Andrew_From_NB]

Hey Andrew! Love the new update and design features! I’d have to throw in my vote for “Maxis”, it’s the first name that came to mind when you mentioned about looking for a name for it 🔥💯👍. Thanks for all your great content! Really enjoy following along and seeing whats going on and what’s new at Eastonmade! 🔥💯👍 Andrew from NB :)

[@FredFlintstone21]

Axis SS for super splitter. It fits. You got the regular chevelle or monte carlo, etc, and you got the ss, which is more! Axis SS!

[@Ridgewood460]

That’s a nice splitter. Cooler is a nice touch

[@mikesherman2612]

That Axis is a freakin’ beast Andrew. Sorry to miss you guys in Essex but I’m sure I’ll catch you in Boonville ? Have a great weekend and be safe

[@EastonmadeWoodSplitters]

We'll be in boonville. See you there

[@jasonpinnix1905]

The auto idle needs to be at least 30 seconds but a very nice unit you have built .

[@tassi13827]

The time to idle should be on a rheostat that can be controlled by the operator.

[@tstep522]

Great, now I am going to be buying one of these now! Haha, Talk to you soon Andrew.

[@ericbrinson9741]

You build incredible machines

[@joeskittino6659]

Just an observation that it seems like the outfeed table is too long. The operator keeps stepping left to feed logs out and having to take another to recenter himself to continue work. Would be more ergonomic and faster if there was some way to lessen movrment. Other than that I think that machine is a beast

[@albertwells8503]

Andrew: How about “The Axis Wood Commander”

[@thomasworatschka6860]

Make a table that can be raised or lowered to accommodate the height of the splitter person

[@hardworkingmanoutdoors]

That thing is a beast. Can the auto idle time be extended a little beyond 4 seconds? I’d be racing to keep it idled up. A little ocd maybe. Great to idle down while loading, stepping away, etc. I like it!

[@EastonmadeWoodSplitters]

Yep. It think we can put an adjustable timer on it

[@765Guys]

I love the constant innovation from you and your team, you guys go the extra mile to make sure your offering the best you can, the line is impressive as it it, can’t wait to see what other machines you revamp! Keep up the great work Team Eastonmade!

[@edfeldpausch7169]

I think you better change the programing of that auto throttle to about 8 or 10 seconds. That would drive me nuts. I see it stalling the machine. Everything else is phenomenal. I agree with the name of Maxis it's bad ass forsure.

[@kahvac]

My left ear enjoyed the video !

[@jimjackson5836]

That thing is sweet!! I would like to have one!!😮

[@OutdoorsEngineer]

That is awesome! Is the timing on the idle down adjustable? I think whatever it is set here is too short. I would think 10-20 seconds would be better. What I wouldn't give to be able to test drive that thing for a few months and show it off on the channel. Would increase production 10 fold.

[@OutdoorsEngineer]

Well it appears you already thought of that. Pays to watch the whole video!

[@OutdoorsEngineer]

Ahh, the beauty of AI: 1. Turbo Axis 2. Axis Ultra 3. Axis X 4. Axis Max 5. Axis Pro 6. Axis Plus 7. Super Axis 8. Mega Axis 9. Axis Elite 10. Axis Power 11. Axis Extreme 12. Axis Prime 13. Axis Force 14. Axis Speed 15. Axis Master 16. Axis Excel 17. Axis Quantum 18. Axis Supreme 19. Axis Titan 20. Axis Alpha

[@kentcorbett5436]

The Axis 2.0 HO for High Output

[@HuckThis1971]

Sweet Andrew ! Beauty eh! Kooolooookoookoookoookooo!!!! Bob and Doug Mckenzie approved!

[@EastonmadeWoodSplitters]

Lol

[@skeets6060]

Axis 2.0 would work,, though I dont think Im too crazy about the auto idle unless you can change the time, seems to me that would wear a motor ,, but what do I know,,, keep up the good work

[@LeBlancfirewood]

You got my attention hope to see it friday

[@buckhammer5897]

Axis Plus, clean and simple

[@lendevonuk5479]

Eastonmade Atomic

[@calvinboyle6441]

Hey Andrew. The Wolfs main predator is the Mountain Lion, also called Cougar or Puma. Puma-Axis or Cougar-Axis are my suggestions Calvin

[@EastonmadeWoodSplitters]

I like that

[@wvhoundhuntingfirewood9106]

Axis Amputator 😂. Very nice machine!

[@bennsellingit3100]

Beautiful machine.. is the Ram still a 14 ton or did that increase also with this larger engine and pump? Thank you for your response

[@EastonmadeWoodSplitters]

No still 14 tons.

[@bennsellingit3100]

cool

[@markprochaska5395]

yup Maxis sounds good

[@stevensfirewood8658]

That’s definitely a kick a$$ machine! I’ve wondered in the past if a motor/pump combo like that would work on a 12-22 with quick connect hydraulic couplers to connect to 24ft conveyor?

[@Bass2010]

Name it Axis SP and yes the timer need to be set at 30 seconds so nice job 👍👍👍👍

[@redeagle6842]

What an awesome machine.

[@dereksstuff8395]

That's really great. It's there a way to increase the "ramp-up" from idle to maybe 10 seconds? Love it. Maybe the axis- pro?

[@tommygunzgunz5986]

Is the idle down feature adjustable because it seems like it would be better with a little longer maby 10 seconds or so would be a little better never mind you mentioned it as I was typing what a grate machine

[@georgekoval152]

Too fahking expensive is an awesome name for it

[@The_Alpha_Channel]

The Axis Performer

[@nickcr1312]

Very nice upgrades. I may need to upgrade as well.

[@saratogafirewood]

o boy andrew the wolfy boys gona love u big time lol the auto idle [eco green] epa aproved 100%

[@PatrickR.P]

The OXis.