Easy learning, the beginners guide to CNC router & Mach3 setting up a job

[@vapoureyes]

You are a man that knows what your talking about. You are explaining everything very well so I’ll be watching all your videos. I’ve an old laptop running XP would Mach 3 run on it .

[@rogerwebb9600]

Yes it will

[@brianconley1732]

I did see you show us what it can do and the 3018 is going to be my first cnc ever since I have had a dremel...This man knows his kangaroo 💩!!! Great work sir and god bless you all and keep safe

[@sioux5755]

Great Job Sir The Best explanation i have seen so far..about CNC . Thank You Sir

[@rogerwebb9600]

You are most welcome

[@tidesrollin5343]

I just got Mach 3 and a brand new lenovo yoga 7 series and Mach 3 works fine.

[@joeygonzo]

A camera or laser crosshair next to the spindle would make life much easier

[@HerrMesser]

thank you! it was very helpful!! greetings from Paraguay!

[@rogerwebb9600]

You're welcome!

[@niceday5463]

Thank you For Sharing, great Job!

[@mperry9025]

Thank you for this info love this ?i am setup a cnc with a slave y and sure how to set up? Love your Chanel........thx

[@DvuongDo]

Thank Roger!

[@umargul5644]

Greater job sir,god bless you

[@greaper512]

Fyi does work with windows 10 64

[@66666tony]

Hi Roger I bought a mill, and rewired it with the new usb breakout board , I have it all working on a 64 bit windows 10 laptop , your tutorial are simple to understand for us beginners , I am struggling with the tool offsets, could you make a video of starting the job as I do a trial run without the stock in and the z is not going to where the top of the stock should be . Regards tony

[@FauziIbrahim]

Thank you so much

[@rogerwebb9600]

You're most welcome

[@sonuverma2796]

Why you not z zero again when you tool change,

[@Ahtraihue]

Thank you!

[@rogerwebb9600]

You're welcome!

[@phil57chev]

hay roger, thanks so much .for all your shows,i learn something every time,but i never learn what i need a long the way,i do have bad cnc work sometime ?

[@rogerwebb9600]

You are very welcome

[@ristovuorela8138]

How do you get that MPG working with mach3 ? I have a same MPG but it crashes mach3. Maybe wrong file. What do you use ?. (win7 32bit, mach3 someting ,066)

[@fredericgiraud5663]

Bonjour monsieur, j ai la même manivelle que vous. comme installer dans mach3 ? J ai déjà une . Mais qui ne marche pas comme il faut .j ai remplacé par une filaire . Merci beaucoup Si vous pouvez m aider .

[@elpee519]

Does anyone know why my g code loads in Mach 3 90 degrees off from what is set in fusion? Appreciate any advice! Thanks!

[@brianconley1732]

Your videos are great but I am not even a newbie yet but I am ordering a cheap one to try one and I am wanting to do carved pictures but I’m getting confused about best place to find patterns for Cnc

[@rogerwebb9600]

Hi, have a look at my 3018 CNC router videos

[@andrewwebster3775]

hi i have mach 3 on my cnc machine and i can not get the machine to work with the z x y i have put an g code in and nothing works can you help me

[@rogerwebb9600]

Hi, have a look at the mach 3 videos I made last month

[@iainpress765]

Hello Roger, thank you for your video. I'm quite new to CNC routers, and I have a Mach3 router, I'm struggling with getting any files to work properly on my router, apart from the ones that came with the Mach3 software. Can you please give me any pointers/advice on how to set everything up properly? I've tried to send a file over to my router in Mach3, but it doesn't seem to recognise the gcode commands to lift the spindle between moves, and I can't work out why... Apologies for the long winded comment. Thanks in advance.

[@rogerwebb9600]

use G-code mm (tap) as a post code

[@iainpress765]

@@rogerwebb9600 I’ve tried that, I’ve also tried .nc, .ngc and more, it just doesn’t seem to work for me at all for some reason…

[@blueknight9748]

you do very good videos....but is there any place to learn how to make the program ?? not just to load it but to create it... I don't know how to do 3D carving...where the picture is raised on the wood not plunged into it....I use Fusion 360... and Carbide Motion...

[@rogerwebb9600]

Hi, yes, I have CADCAM programs on my KZbin channel Carveco, ArtCAM and Aspire.

[@timd8142]

if using a usb breakout board it will work on windows 10 64 bit laptop

[@rogerwebb9600]

No it will not, you will need an older WIN 7 or 8 laptop that has WIN 10 running on it, as Mach 3 needs a 32 bit operating system

[@partibensuppiah9113]

Roger can i know if the Mac3 is stable on a laptop computer? Because i see allot of comments stating that it should be run on a PC rather than laptop. Just need your input. I have a laptop running windows 7 32Bit laptop. Which i plan to upgrade to windows 10 32bit just to run the Mac3

[@rogerwebb9600]

I think its ok

[@partibensuppiah9113]

@@rogerwebb9600 i have seen on your video that you are using a laptop with extended larger monitor for the mac3. So far any issues that you have faced running mac3 on laptop? Does it have any form of issues while running continuously for hours?

[@mperry9025]

In Mach 3

[@rho35100]

Can not find the videos with more match 3 tutorials

[@rogerwebb9600]

Hi, have a look in my playlist lots on Mach 3 there

[@rho35100]

@@rogerwebb9600 i like your videos. But I would of been helpfull a little more continuity on the mach 3 tutorials, instead of having to "fish" them up from your play lists. Any way. Grateful for the effort

[@cherylcarey6600]

What brand is the pendant? Do you have a link for it?

[@rogerwebb9600]

Hi, the information you need is in this video link. kzbin.info/www/bejne/iX3Xi3qijayKf5Y

[@cherylcarey6600]

@@rogerwebb9600Thanks, but there is a different pendant controller in video #400. Which one is this?