EASY: Turn Off Check Engine Light for FREE

[@chuckf4333]

Success !!! 2004 Toyota Sequoia vsc,track and engine lights on after a minor service. 3 clicks didn't work. Remove left terminal connection, cleaned everything up, waited about 10 minutes, reconnected and bingo! Lights out! Thank you VERY much. Saved a trip to the mechanic and a costly diagnostic appointment.

[@TightWadDIY]

Nice work!

[@girlygirl1890]

My check engine light came on. I went and got an Oil Change and the Engine light went right off immediately. Havent come on since. Thank you for this video, at least it told us to check other options before spending a whole lot of money. Thanks so much. Gereat video.

[@TightWadDIY]

My pleasure!

[@josephinesmith7876]

Good

[@chudstyle]

That would have been the mechanic resetting if after the oil change 😂

[@agnessmith9313]

OMG. My check engine light was on for a couple days. I went out and turned the ignition to 'on' three times and it went OFF! You saved me a trip to the dealership...and lots of $$. Thank you!

[@TightWadDIY]

I’m glad it reset. If it comes back on, make sure you have your codes pulled for free at an auto parts store.

[@cdang6663]

@ TightWadDIY I am 87 years old, and the temp out there is 87 but feels like 97 ! Have driven my 16 years old Camry for 3 wks now with the check engine light on, and a New gas cap. I first tried the 3 time...On, off.... Didn't work. Then, next, battery neg. off. Works like a charm !!! What can I say ? Thanks a million TightWadDIY.👍🙏

[@mrtwista5794]

So glad there are people out there that do things, not just for financial gain but just because it's the honourable thing to do!

[@TightWadDIY]

Truth be told, I love teaching and fixing things but I do actually make money for posting on KZbin.

[@AdanPerez-yx4eg]

@@TightWadDIY my chuc

[@DavenHiskey]

😱​@@TightWadDIY

[@mandyjacobs726]

😅😅

[@sethkyere7602]

I solved a check light problem simply by closing the gas cap. I love this video.

[@TightWadDIY]

Nice! I’m glad it worked!

[@nanapoku5259]

Is one week okay to take the car for emission test after taking off the check engine light? Also, do I necessarily have to take it to auto zone to reset the code after a week before taking it for emission?

[@justtester_9962]

Cleaning the gas cap didn't clear those lights, but removing the negative battery and leaving off for 5mn worked for me and I didn't lose my radio settings.

[@TightWadDIY]

That’s great!

[@Lordismyshepered]

Dude, it really worked. The TCS light disappeared when I switch my ignition to on position 3 times. My check engine light went away as well when I removed the negative post & let it sit about 5 mins. I thought it was going to cost me a lot if it wasn't for your video. Thanks men!!😊

[@TightWadDIY]

If it comes back on, make sure you have your codes run.

[@MarysolPantoja-iv7ue]

Great video thanks worked for a 2000 Honda LX V tec engine

[@coreyjones8912]

It work 3x to acc on my 2016 chrysler

[@iandawson9945]

​@@TightWadDIY.q3⁴⁴¾q4q4⁴😊😊

[@themac9344]

I'm so glad you informed others including myself on not going straight to emissions to get a test because I just went and got my Gas pump assembly replaced and my engine light was still on so I came home and tuned in to your channel blog and took off the ground wire for 5 min and worked successfully now I will wait and drive for 2 weeks before going to emissions

[@carminesemioli8293]

i had a check engine light come on. got it checked at autozone just a thermostat issue. had 20.00 in rewards from autozone and paid 1.61 out of pocket. came to KZbin learned how to replace it. I was waiting for the check engine light to turn off. Then decided to look up how to manually turn off a check engine lightCame across your video and the battery terminal wire wire worked flawlessly. thank you

[@TightWadDIY]

That’s great! Hopefully you are all good to go now.

[@onalennalemo8571]

Thank you so much 😊 a dealer was telling I need to replace some engine part and mentioned a very expensive amount. Maybe because I am a woman so I thought of listening to your videos now I will ask intelligently

[@TightWadDIY]

Yes! Go to the auto parts place and have them pull your codes for free. Take the codes and Google them to find out what they mean.

[@jesusonlywaytoheaven1463]

I want to thank you guy for this video . My car was with engine light on since yesterday . I went to work today worry, then I saw this video . I did the same as you did, unplug the battery about 5 min. When I turn on my car , the engine light was gone. Thanks again !

[@TightWadDIY]

Turning off the light doesn’t solve the problem though….

[@RN-jq9mb]

It will appear again after few minutes

[@JosephMbidi]

​@TightWadDIY ahahahahahahahaa. Turn off engine light is temporarily. It will be back and you guys need to find the mechanic to fix this problem 😂😂😂😂😂

[@tom2754]

The ignition 3x worked for me. Check engine light came on after I cleaned the throttle body and mass air flow sensor. Thought I broke something. This did the trick. Thank you.

[@Afrancis2774]

Turned key to ON position 3 times and light disappeared on 2004 Camry!! Woohoo!! Thank you so much!!

[@TightWadDIY]

That’s great! Hopefully your issue is fixed too. If the light comes back on, go have your codes run for free at an auto parts store.

[@twindread3052]

I put diesel in my 4runner, it did not go far , i had to drain the tank and clean the pump and filter. Everything was fine until the next morning ,the check engine light came on , so i came across your video on how to turn off the check engine and track off by disconecting the negative terminal waited 3 minutes before starting, check light went out , thank you so much for shearing these tips 👍

[@TightWadDIY]

If it comes back on, go have your codes pulled.

[@dougiemac8417]

Thank you for the quick fix information. I'm experiencing the same issue. My check engine light and my traction control lights are on solid not flashing. I'm going to try this in the morning. Pray for me. 🙏🏾

[@snetiengineeringltd8246]

Feedback

[@williamrandolphjr6807]

these are great tips esp., on the gas caps maybe old & time to change them, however, if you have a pre- 1990-94 NO AUTO STORE will check this cause they don't have an OB1 READER,the OB2 is only for 1996-NEWER I have a 94 Oldsmobile Cutlass Supreme S 3.1lt & my check engine light comes on every so often, but none could find anything wrong

[@mercylewis5373]

check enjin light is not coming on car is dead wont start

[@mercylewis5373]

car dont want to start

[@nadimchadi9617]

I had same issue with my car and I’m gonna try these steps tomorrow morning if it’s worked i will share your videos to all my friends

[@TightWadDIY]

Please do

[@apuzyr]

Glad to hear you warned about NOT going to Motor Vehicle inspection right after resetting the check engine light. Their computer system will know it and fail you. Saying this from experience.

[@TightWadDIY]

PowerPunchingSecrets.com That’s right! You can’t blatantly cheat the system.

[@blesstone2562]

Is that right! Thank you 😇

[@Hummer999xx]

I went to get the emissions done right after I reset the code. I drove the car for 5 minutes. No issues with passing. I have a 1998 Honda Accord. Been doing this for the while.

[@MelodyFaithClark]

Can you still get get passed on the inspection if you have a check engine light on?

[@MelodyFaithClark]

@@TightWadDIY I have a Toyota Prius I think my problem is probably my gas cap but I'm wondering if you go get your car smogged will it pass if it has check engine or not?

[@jman2005]

Thanks for the upload. Disconnected the negative battery terminal for three minutes and it worked. Replaced the EVAP purge valve on my 2019 Ram Bighorn for the codes it gave, but the check engine was still on after the repair. Your tips cleared it up. Thanks. 👍

[@TightWadDIY]

I’m glad it worked for you too.

[@randomvideoconnoisseur563]

Unfortunately in Canada, most places charge $140-190 just to plug their diagnostics tool in. Right now I need an 02 sensor replaced and I already know the issue from plugging in my friend’s obd code reader. I went to multiple repair shops and they all say they have to charge me first to plug in their own device even though I know what the problem is. The total cost to change 1 o2 sensor will be above $700

[@TightWadDIY]

Sounds about right. Their “diagnostics fee” is their biggest money maker because they get $100+ for a 5 min diagnostic. You are really paying for their knowledge but it’s a bit much. Find a place they doesn’t charge the fee as long as you let them do the repair and you will know you have a good shop.

[@randymcmanus8691]

If there's an issue the light will come back on after resetting usually within 20 miles or so and it will keep coming on until issue is resolved

[@RN-jq9mb]

You are correct

[@Jim-bx7vs]

I had this light come took it to O'Reillys in glenwood IL. They scanned it turned out to be the thermostat i replaced it disconnected battery cable ,all is well thanks for sharing

[@TightWadDIY]

That’s great!

[@chefarm9798]

Omg! It was my gas cap🙄 .. I was so close to taking it in.. God knows what they would have told me it was.. Wow, thank you!!

[@TightWadDIY]

I’m glad you checked here first!

[@justtester_9962]

You can go to Advance Auto Parts and they will let you use their diagnostic tool for free instead of paying $100 or more at the dealer.

[@TightWadDIY]

@@justtester_9962 That was mentioned in the video.

[@kalaKHAN-ig8kn]

Thanks Mr. i am from Norway and i just paid 100 us Dollar two days before for just this job .

[@TightWadDIY]

Sorry that happened.

[@kusuko..scla..213]

I just did it with the key..and is gone THANK YOU SOOOOOO MUCH!! I was SOOO worry Abt cuz right now I'm 450 miles from home.. TTHANK YOU YOU THE GREATS !!!

[@TightWadDIY]

That doesn’t mean the issue is fixed. I just means you turned off the warning. If it comes back on, you still need to have your codes pulled.

[@brighteyes6559]

@@TightWadDIY Does the computer ever throw codes by mistake? I got a code P0793, but the car runs fine and smooth. Didn't experience any problems with driving. I will try to erase the code, and hopefully the computer just made a mistake and the code won't come back.

[@TightWadDIY]

@@brighteyes6559 Not really a mistake but a temporary issue caused by bad fuel or. Loose fuel cap can cause it.

[@adriannraden7366]

It is so good too have people like you guy's out there,thanks so much

[@TightWadDIY]

My pleasure.

[@mariejean2628]

Thanks for showing this video I have my check engine light & the VTM-4 on what does I mean?

[@arnoldbelaj6988]

Thank you thank you thank you may you have a fabulous year. The best wish i can think of. You ve saved me a lot of money and time and stress with a simple video. This is how internet should be used. Bravo 😊

[@GlennDavidBeatty]

Smart, simple, easy to understand, especially for novices.

[@TightWadDIY]

I’m glad you found it helpful.

[@angelaprince7698]

It is great to have people like you. My check engine light is on a reading says the transmission is malfunctioning.

[@TightWadDIY]

I’d go get that checked out. Turning off the light isn’t solving the issue.

[@proscentgifts]

What was it to fix? I have too with solid light.

[@cruella5016]

I'm going to try this after work today! If it works I will be sooooo happy. I have a feeling it won't because I usually don't have things that easy lol. Thanks for the video.😊

[@TightWadDIY]

Just turning it off won’t fix your issue. This is mean to turn it off after a DIY repair is done.

[@Mibonitodesinaloa]

Oh my god!!! THANK YOU SO MUCH. YOU LITERALLY SAVED ME FROM SO MUCH !!! I was soooo worried, I turned the key twice and engine light went off. 🙏 Im sure I would have gotten ripped off. Thank you so much. GOD BLESS YOUUUUUU!!!!

[@TightWadDIY]

You’re welcome. Now if the light comes back on, go to an auto parts store and have them pull the codes. Somewhere like Auto Zone or Advanced Auto will do it for free.

[@Mibonitodesinaloa]

@@TightWadDIY love you!

[@justtester_9962]

Now they let you do it yourself with simple to follow instructions on the code scanner, and then you get a free printout inside if you want.

[@williamarandolphjr4649]

If you have an older model like my 1994 Oldsmobile cutlass supreme s 3.1 Lt.that means that you have an OB1 port and auto parts stores don't have an OB1 scanner,there for they can't scan it

[@leonardkoczor8380]

Use a paperclip then count how many times it comes on then go online to find codes

[@bestiehandsfreeblowdryerho7701]

Hi! I have a 2006 Toyota matrix and was told that the check engine light sensor was disabled intentionally. Do you have a video showing how to possibly fix that? Also the lightbulb in my gear shifter is out for you have a video how to take that apart and put in a new lightbulb or check to see if maybe at some thing else? Anyway, thank you for your video that was really cool and insightful.

[@TightWadDIY]

Sorry. I don’t have a video for either of those.

[@liban4217]

Very helpful! I followed your advice to remove and reinstall the battery, and it worked perfectly. Thank you!

[@TightWadDIY]

If it comes back on, make sure you get your codes pulled

[@dingminmin5754]

This may not solve the problem. You need to get the code and fix the problem.

[@Rick-or2kq]

For emission tests to pass after resetting the computer drive it at least 100 miles before taking it in.

[@TheSageSpartan]

You don’t need to drive 100 miles

[@pvsheridan]

Thank you TW. I updated a BUNCH of stuff (TPS, etc.) on my drop-dead mint 2007 MGM (24k miles), and light appeared. 'Did the routine you shared, and no more light. Thanks so much.

[@TightWadDIY]

Great!

[@lyxaduong5530]

Scorry Kilmer has highly recommended people do not short circuit the negative terminal directly to the positive one, but use any big 1 Amp resistor of 1K to make the short circuit trick.

[@fongfutube]

Satisfied follower of your channel. Followed instructions and the first 3 clicks to ignition solved the check engine problem on my 2016 GMC Terrain. Thank you!

[@TightWadDIY]

That’s great news! Glad to that works on the GMCs.

[@weriesblack1375]

Why does the 3 turns to on remove the check engine light and does it reset any electronics or just remove the light mine came on after a engine wash and now my cruise control wont set and i have the light on. Any help will be apreciates

[@lonnellware3055]

My toyota 1995 toyota engine light showed! I removed the cable and waited for a few minutes and the engine light turned off! Thank you very much!!!!!!!

[@sincengilemkhize1377]

Thank you very much for this helpful clip Does it mean the proces closes the slippery light as well Thank you

[@TightWadDIY]

It should.

[@thomasfriis3556]

Thx dude. This was really helpful and solved the problem. Well filmed and precise advice 👍🏼

[@TightWadDIY]

Great! I’m glad it worked for you too!

[@sunilayya8948]

Pls clarify that if so required , the negative terminal should be connected to the positive terminal only when both terminals have been removed from the battery.

[@williamyoung369]

Clean the gasket inside the gas cap & all around where it seats. Check the gasket for cracks. A paper towel & some WD40 works. Freezing weather may shrink the gasket. Maybe time for a new gas cap.

[@TightWadDIY]

All great tips.

[@UltimateForceMarketing]

Better NOT use WD40 on most ANY rubber, it simply dries out the lubracating or natural oil compounds out of the rubber making it become brittle over some time. Best purchase some 303 lubricant spray it helps restore the natural compounds in Rubber therefore making the rubber components last a long time!!

[@blesstone2562]

I failed inspection of 0432 and my car runs good.! Thank you I'm going to try this today!

[@rodbutler8069]

Do not run a jumper to the positive terminal unless the terminal is OFF the battery.

[@UltimateForceMarketing]

Absolutely Correct!!

[@Falconlibrary]

How to turn off the check engine light: Disconnect the cable to the NEGATIVE terminal of the battery ONLY. Then turn on the car's headlights and honk the horn 4-5 times to bleed off any residual energy. Wait 1 minute, then reconnect the cable. The light should be off. If the light comes back on after driving the car for a total of 20 miles, go to an auto parts store and have them read the error codes for free. NEVER ignore or turn off a FLASHING check engine light--that's very serious and needs immediate diagnosis and repair. (I used this method with my 2000 Lexus GS300 after the check engine light came on after an air filter change--the light did not come back on during subsequent trips.)

[@mohinderpauljatana2176]

4:45

[@robertday4204]

DHS. U7 ru jo. I,,,, i.9

[@AlexRodriguez-5.0xplo]

Idk about the honking part bubba

[@pahbsd]

I did turn the key 3 times and it worked! Thank you

[@TightWadDIY]

That’s great to hear! If the light comes back on, go get them to pull your codes for free at an auto parts store.

[@princesen0608]

Yes sir good job & well done but remember to mention it works with only older models😃after 2000's those cars are not the same...thanks👌

[@TightWadDIY]

Thanks.

[@billwagoner5423]

That is not a fix .that light will be back on before long. I have been doing that do months on mine and it will always come back on. Sometime before I even leave the drive way. Sometime longer, but it won't say off I guarantee u that much. K

[@GrillThisSmokeThat]

@@billwagoner5423 This video actually discussed the possible source of the light coming on. Fix your gas cap seal and turn off the light. If it comes back on, there is a different issue. It’s definitely a fix if your gas cap was the issue…right?

[@Nana-jn7uu]

KZbin has a solution for everything.. thanks for the video

[@TightWadDIY]

My pleasure!

[@camdix3250]

Thank you so much for this. You're an excellent teacher. Concise and to the point. Excellent! Best wishes.

[@TightWadDIY]

Thanks! I’m actually a school teacher. 😂

[@camdix3250]

@@TightWadDIY I'm a retired school teacher as well! Your teaching is brilliant. I know squat about cars, so it's thanks to folks like yourself that help those like me. Warmest regards.

[@gloriatorres2198]

​@@TightWadDIYh😂😅😊😊😊😊😊😊😊😊😊😊😊¹¹😊1

[@syudi2012]

I bought a used 2011 Chevrolet Malibu LTZ sedan and at the time my mechanic wasn’t around so I trusted the guy well after getting it home my mechanic came to check out the car because the water pump broke and he said the guy who sold me the car turned off the check engine light because he knew the timing chain was going out on the car . Saved all my money for this car single mom on ssi 😢😢😢

[@DSmith-ix1xf]

Any deal that seems to good to be true, probably is. Bet that won't happen to you again. 🍀

[@kimberlysmith1082]

I just did the battery trick...it worked. Yippee thanks buddy

[@TightWadDIY]

Great!

[@teller628]

well the check engine light can mean many things, and being on is not a catastrophe, however if the thing starts flashing you better get it off the road immediately, or so my mechanic son tells me.

[@thomvogan3397]

He said that

[@FrancisBaker-zt7wc]

I appreciate you kindness by sharing these tips....thank you

[@TightWadDIY]

You are so welcome!

[@alexanderlopez3033]

Well did everything you said not to do on my ‘04 tundra and didnt have a problem lol. In a strict state as well

[@josephrufus7684]

What after all these, the lights still on. What do we do again and what actually are the causes of the vacuum and traffic off light on the dashboard

[@TightWadDIY]

I suggest going to an auto parts store and ask them to pull your codes. It’s usually done for free.

[@NathanRagland]

Good morning, That is a great job, you are the best truck fixer ever!!! I enjoy watching this video! Have a great day My name is Nathan Ragland

[@TightWadDIY]

Thanks Nathan.

[@NewYorkF150stx]

Thank you much... Bro! Absolutely worked. Thank you so much for sharing this video. Hyundai Santa Fe Sport 2013 👋👍🤙

[@TightWadDIY]

Glad it helped

[@katprince5528]

If you unhook the battery or clear the trouble codes with the scan tool will you reset all the monitors too? If so,you need to put the vehicle through a system of drive functions and the vehicle will fail without the monitors set even with the check engine light OFF.

[@TightWadDIY]

That’s correct.

[@at8630]

I see your vsc and vtrac lights were on too. I have that issue with the check engine light also. How did you fix those? That was more than just disconnecting the battery, wasn't it?

[@jannordlund6153]

This proceedure usually will not fix the problem. its best to use a obd code checker to find out what the real problem is and fix your peoblem from there.

[@mohayooahmedova7281]

What a amazing idea thanks a lot I hope learning further about 👍🏻

[@TightWadDIY]

My pleasure 😊

[@jwatt9570]

My hummer h3 had check engine and tpm lights on. Disconnected the negative battery cable. Re connected and "bingo" all clear thank you.

[@GHOST5663]

The ignition trick worked for me, Thank you.

[@TightWadDIY]

Great!

[@Jesus.Love.Saved7]

That was a excellent video cause. I have that problem with the engine light. Thank you I probably need to get rid of this car

[@shanie_76]

2004 lexus es330 removed battery check engine light went off. Drove 5 miles light came back on. What should I do need to get inspected...and have taken it twice to repair shop ($400) and within a couple days light comes right back on!

[@TightWadDIY]

First…Find a new repair shop. I would take it to an auto parts store to have my codes pulled. This is only meant to turn off the light after you fix something or tighten the gas cap.

[@thedbcooperforum]

This only resets the computer. if an issue is causing the light, it will come back on within a certain amount of miles or time.

[@TightWadDIY]

Yep. That is discussed in the video too.

[@claytonturner5740]

Not an lsd light it's traction control

[@josephinesmith7876]

How will staying off

[@stevendegiorgio3143]

I usually just disconnect my negative batter terminal and let the car sit for an hour.That works for me all the time.

[@TightWadDIY]

That works too.

[@tntathean4409]

This really work even for the MZR 2.3 l madza 3 wow 😮❤❤❤❤❤ cheers bro

[@TightWadDIY]

That’s great!

[@chandlerwilliford8448]

Thank you so much I have this exact issue with my Tundra. This resolved it. Thumbs up and subscribed thanks again

[@TightWadDIY]

That’s great!

[@mariesilver9162]

Thank you so so much, the key trick worked!!! You saved me a trip to the repair shop!

[@TightWadDIY]

Just to clarify: turning off the light doesn’t fix the problem. If you didn’t change anything it will likely come back on and you will need to go have your codes pulled.

[@mariesilver9162]

@@TightWadDIY It's been a couple weeks since I turned it off and it hasn't come back, so fingers crossed. I may not have had the gas cap tightened enough.

[@TightWadDIY]

@@mariesilver9162 That’s great!

[@ritanelson4651]

I did what needed to be done to fix it and your second option work. Thank you so much, sunscriber👍🏼😊

[@TightWadDIY]

That’s great!

[@NgocNguyen-lx2jf]

Thanks for the videos lots easier than others posting.

[@TightWadDIY]

Great! I’m glad it worked for you too!

[@Yemith_Gaming]

I guess it depends on area, but the auto parts store, I work at, we are explicitly told to never clear the codes for customers. They even send secret shoppers to make sure and it is firable offense.

[@TightWadDIY]

Im not recommending they clear the codes. You can just have them tell you what codes are causing the light to come on.

[@philhohnen6193]

The "check engine" light has been coming on and remaining on at random in my 2005 3 Litre turbo Toyota SUV for many years. It goes into "limp home" mode then. Dangerous on the highway. I took it to a dealer here in Thailand, who replaced the injectors, to no effect. I discovered that if I turn off the engine for 2-5 minutes and restart, I can continue on.

[@t.5610]

Thank you for the information question what causes the stability track light to turn on and service engine on although got vehicle serviced after repairs to heads and addition repairs the check engine light went on a week later and hasn't turned off know my vehicle starts but stays on for a few minutes and shuts off. Thank you. Veh is a 2015 Chevy Cruz.

[@TightWadDIY]

Sorry, it’s hard to say. You’ll need to plug-in and OBD reader to see.

[@rickybs34]

the 3 times turn on and off got rid off it thank you

[@TightWadDIY]

That’s great! If it comes back on, go have your codes pulled.

[@j.d.schultzsr.9215]

I bought a cheapo Chinese OBD code reader which seems to work. As long as the car runs OK, I prefer my wife's solution: Stick a piece of black electrical tape over the "CHECK ENGINE" light. Problem solved without breaking the bank!!

[@TightWadDIY]

Haha.

[@Camry-pe6up]

Thanks for your video. The stated way for putting check engine light off, is tbjs procedure sutible for Toyota Camry XLE.

[@tomsut123]

what does a jumper wire look like and where to get one? Thank You

[@TightWadDIY]

You’d want to use a low gauge wire like 6g. You back buy it at any hardware store.

[@chrissyrodriguez1166]

Thank you so much for your help. And explaining so well and in detail you're Awesome!!! 👍👍😊

[@TightWadDIY]

Glad it was helpful!

[@felixdoleguez4846]

The check engine was diagnose with bad ECT sensor using diagnostic test....is the ECT to be replaced or other test will be made before ECT replacement....thanks

[@charlesgreen8267]

Hey my boy I just want to say thank you I look at your video today and guess what you save the day frfr big God bless frfr and thank you I'm post this on my Facebook account ok. So you know ok.

[@TightWadDIY]

Thank you!

[@Jul0570]

Youre the man! It worked! Many thanks bro

[@TightWadDIY]

You're welcome!

[@travisvalentine8252]

I have a 1988 Chevrolet Silverado c1500 2wd 5.7engine . Auto parts stores say my truck is to old they can't check it

[@rosemitchell921]

This was very helpful 👌 Thanks for sharing

[@TightWadDIY]

My pleasure!

[@LynnElliott-xd3hq]

2000Jeep Cherokee Sport. We replaced the downstream Oxygen Sensor and the Neutral/Park Safety Switch Sensor. That cleared two codes. We still have a nonflashing check engine light orange. We cleaned sludge out of transmission pan and put in new filter, gasket, and fluid. It drives good. But we still have P0705 Transmission Range Sensor. Went to Auto parts store and they couldn’t clear it. We don’t know what to do. Please help.

[@TightWadDIY]

Call your local service center and ask them what the most common cause is.

[@gregorykearney8482]

i got that light on plus cruise control and tried everything, but it was an oxygen sensor. as i remember.

[@TightWadDIY]

Yeah. Sometimes there is truly an issue you need to have repaired.

[@exploringallaround]

I have a 2011 cruze lt. I want to ask something regarding the gas cap. In my car, the gas cap is with key but i didn't get the key from where i purchased my used cruze. So the gas cap is without key and it doesn't lock there properly, click sound comes, but it still remains loose, even with click sound i can just lift off the gas cap it will open, it never tights. Maybe because i don't have its key?? Also in my car, engine check light is appearing, it's not blinking though. I think that due to this gas cap, the engine check light is appearing maybe. Also my car is burning a lot of fuel, the crazy thing is when i leave car at park in the night and again go back in the morning the fuel shows 1-2 needle less on the meter as compared to when i checked at night. Why is this happening and what should I do?? Thanks.

[@TightWadDIY]

I would order a new gas cap. Your fuel could be evaporating.

[@exploringallaround]

@@TightWadDIY can I order a keyless gas cap, does it affect my car? Because the gas right now is with key and this gas cap is broken I think because it never tights

[@GrillThisSmokeThat]

@@exploringallaroundYes.

[@sydneydennis4542]

What about keyless ignitions to reset outside the battery cable removal.

[@TightWadDIY]

I’m really not sure.

[@aderloustonluc6511]

I haven’t try it yet, but thank you for the information 🤝

[@TightWadDIY]

You’re welcome!

[@siriqballectures2644]

Thank you you explain the problem very easily again thank you very hank you very much and

[@TightWadDIY]

Happy to help

[@philliphall5198]

Really having a master cut off switch is very handy to reset light

[@TightWadDIY]

Agreed!

[@johnwright3951]

Can you remove a fuse and put back in to reset the check engine light? I have a 2005 Toyota matrix

[@TightWadDIY]

Possibly.

[@habibshaikh389]

Very nicely explained sir

[@TightWadDIY]

I appreciate the kind comment.

[@hepeli2]

If I will get the motor warninglight blinking and also a accimalator light as well is the accumalator or charcher off on duty? My car is Kia Ceed 1,6 ,2011

[@lavaeseai892]

Thank you for sharing. God blessings.

[@rayvillarreal1225]

My check eng light keeps coming on even after I replaced EGR and cleaned tube and reset system. What can do???