Easyguard 003 issues

[@joseahernandez4771]

Hope you can help me out Love the remote push button start only issue i have and my installer cant figure out when i turn on the turn signal wont work

[@justinmckibben4534]

maybe you have a bad unit? did you try to set it up on a bench like mine? or just hook up a meter to the module in the car to see if theres voltage reading

[@GoldenLikeShowers]

Hello I bought a car with what i believe is this unit. How do i operate the remote start?

[@justinmckibben4534]

hold center button for i think 5 seconds. Careful though because car will shut off automatically after 20 min or so if it wasn't wired properly

[@vincentaltamerano928]

Hey I have a problem with the easyguard ec002 i got it all hooked up the car start with the push to start but it dies right after. What could be the cause? I hooked up the blue oil path wire to a 12v constant because I dont know where the fuel pump wire or oil is /cant find it in my 2008 kia sportage.

[@martingonzalez-z2f]

Hola tengo el mismo equipo y no puedo instalar por que perdi el manual ¿me podrias enviar la copia este mismo equipo??

[@justinmckibben4534]

google the make and model its online its only one or two pages i think

[@martingonzalez-z2f]

​@@justinmckibben4534 no me aparece este modelo le que figura es el mas nuevo

[@pweezy68]

I’m barely about to install mine in my 49 Chevy pickup 😩

[@justinmckibben4534]

if you need help lemme know... sometimes if your vehicle takes too long to crank it stops trying too soon.... other than that it should work i think?

[@anthonysteptoe3356]

What is the green wire for

[@erikcaban2727]

The siren output is constant or intermitent

[@davebeltran1358]

My issue is the truck starts but won’t turn off. Has anyone had this problem?

[@justinmckibben4534]

That's weird. Have you tried shutting it off via remote?

[@davebeltran1358]

The remote starts it but doesn’t turn it off. I am manually trying to stop it but nothing

[@justinmckibben4534]

@@davebeltran1358 you sure that brake light signal is hooked up??

[@claudiahernandez8711]

I'm back tracking on the wires as we speak. I had to remove the console and other after market things that the original owner installed. Thank you very much

[@claudiahernandez8711]

​@@justinmckibben4534how do you do that?

[@chikilinks]

Amigo disculpa tu sabes cómo le puedo programar un control? Se perdieron los originales y conseguimos uno que según es para el modelo Easyguard EC003N pero no logro programarlo

[@justinmckibben4534]

¿Cómo programar el llavero? No estoy seguro de enviar un correo electrónico a Easyguard en su sitio web...

[@justinmckibben4534]

Used mutliple actuators as well...no cigar!

[@adyjames8204]

Hey. When I bench tested mine it didn’t act right. Turned out that my bench power supply didn’t supply enough power. I had to turn it up to 14-15 volts.

[@justinmckibben4534]

@@adyjames8204 my issue was power supply was inadequate too! Was such a relief to figure that out... Installed in my car has been great except the pke range is junk and the remote start range not so great

[@justinmckibben4534]

When I replace the actuator with an LED, it works great....

[@choochooelectric7381]

do the actuators need to be "direct" grounded? I know this is a year past but Im interested in how this all came out.

[@justinmckibben4534]

@@choochooelectric7381 Not sure what you mean I don't think it would make a difference where you attached it if it had continuity to ground?

[@JuanLopez-gg7zy]

I installed but My pager isint syncin to My alarm tried with code learning an no luck ,🥺

[@justinmckibben4534]

You have this same model?

[@justinmckibben4534]

Are you sure you are using the same model? On this one everything is programmed at factory and there are two pagers, only one active at a time

[@preluesamuels4713]

How can I get a replacement key fob ?

[@justinmckibben4534]

You can email easyguard they will help you

[@anthonysteptoe3356]

I have 1 my car will not start think it has something to do with the green wire

[@justinmckibben4534]

Green is fuel pump wire. + Positive. Try hooking it to +12v (can splice to the bigger white wire)

[@justinmckibben4534]

What I did was build and solder a voltage divider circuit to make 5v from 12v. Basically to simulate a tachometer. I don't think you need to do that though, just splice it to the big white wire from the 6-wire harness.

[@justinmckibben4534]

If you don't hook the green wire up, when you try to start it remotely, it will keep trying to crank the starter while it is already running....Is this what is happening??

[@justinmckibben4534]

You can also splice to white wire from the 6-wire harness, if that is your issue....

[@miguelmercado9176]

que puedo hacer si cuando utilizo el encendido reomto se sigue encendiendo el motor de arranque_?

[@justinmckibben4534]

No estoy seguro de que te entienda totalmente. Cuando usa el control remoto para encender el automóvil, ¿el motor sigue intentando arrancar después de que ya está funcionando?Si es así, debe conectar el cable del tacómetro.Nunca encontré mi cable de conexión, solo hice un divisor de voltaje con dos resistencias para imitar la señal del tacómetro.Traduje esto a través de un sitio web

[@justinmckibben4534]

@Bryson Hodge not sure if I answered your question in my prior response (i used google translate) but your alarm module is not receiving proper tachometer signal. Dont let it attempt to start after it runs you will sheer your starter key

[@ricardonicolalde3657]

Conecta el cable de la señal de cartera al on 1 o 2 y asegúrate del cable de freno de mano

[@saeedsaleh6784]

I forgot password can you help me to reset

[@JuanLopez-gg7zy]

Help me out please!!

[@justinmckibben4534]

????