PUSH START & STOP BUTTON installation | No Splicing of Wires

  Рет қаралды 88,278

VIOSIFIED Car DIY

VIOSIFIED Car DIY

Күн бұрын

Пікірлер: 404
@Viosified
@Viosified 2 ай бұрын
If you'd like to support this channel, which is never expected but always appreciated, please use this link: paypal.me/Viosified?country.x=PH&locale.x=en_US
@MLK.PaNoRaMa
@MLK.PaNoRaMa Жыл бұрын
I was going to watch a few clips of push start installation and i click on your fisrt, your clip is one stop shop seriously, very clear very nice photos and instructions, thank you again
@Viosified
@Viosified Жыл бұрын
Thank you, I appreciate it! Thanks for watching.
@richstanton1425
@richstanton1425 2 жыл бұрын
I've been put off installing a kit like this but your vid so precise, clean and direct. Nice one.
@Viosified
@Viosified 2 жыл бұрын
Thank you for your feedback. I hope the video was helpful 😊
@kabirraji7341
@kabirraji7341 2 жыл бұрын
same here now am ready to give it a shot
@kabirraji7341
@kabirraji7341 2 жыл бұрын
THis is the best pke installation video have seen so far Thanks man
@Viosified
@Viosified 2 жыл бұрын
Thanks! 😊
@stephenadimonye1772
@stephenadimonye1772 2 жыл бұрын
This video is very precise I guess the knowledge gained here will help me install the one I just purchased
@Viosified
@Viosified 2 жыл бұрын
Thanks! Good luck :)
@awakenedblacktivist7018
@awakenedblacktivist7018 Жыл бұрын
BEST video hands down. 2 thumbs up.
@Viosified
@Viosified Жыл бұрын
Thanks so much
@mixbox3081
@mixbox3081 Жыл бұрын
Thank you very much this is the most easiest and clear steps to follow
@Viosified
@Viosified Жыл бұрын
Thanks for watching 😊
@Viosified
@Viosified 2 жыл бұрын
Recommended Tools/Products: amzn.to/3rGcBML FOXWELL NT301Professional OBD2 Scanner: amzn.to/3sBa6KW ANCEL OBD 2 Scanner: amzn.to/3JiCiZU Fully Automatic Smart Battery Charger: amzn.to/3gCbKGP Digital Tire Pressure Guage: amzn.to/3GKsmqe BOSCH Wiper Blades: amzn.to/3uH8Qss Bumper Retainer Clips: amzn.to/3LuuK88 Fully Synthetic Motor Oil: amzn.to/3szZjAF Panel & Trim Removal Tool Set: amzn.to/34Sw9o8 1000 Amp 12volt Car Jump Starter Pack: amzn.to/3JiEsJ0 Phone Mount for Cars: amzn.to/33hwYXs FOXWELL NT301Professional OBD2 Scanner: amzn.to/3sBa6KW VACLIFE Tire Air Inflator/Compressor: amzn.to/3JnGpDQ AT-205 Re-Seal Stops Leaks, 8 Ounce Bottle: amzn.to/3Lttu58
@gameztester8387
@gameztester8387 2 жыл бұрын
Man your the best one how made a video installing start stop button your explains all the important details and puts all the steps on the camera nice video man keep the nice work
@Viosified
@Viosified 2 жыл бұрын
Thank you so much! 😊
@gameztester8387
@gameztester8387 2 жыл бұрын
@@Viosified do you have video how to install start stop button keyless entry??
@Viosified
@Viosified 2 жыл бұрын
Sorry, I don't have a video on that
@rshinn8776
@rshinn8776 2 жыл бұрын
This was the best video on installation
@Viosified
@Viosified 2 жыл бұрын
Thanks so much! :)
@שיעוריהרבמשהביננשטוקשליטא
@שיעוריהרבמשהביננשטוקשליטא Жыл бұрын
That was a great video, thanks! can you do a follow up video on remote push start installation with pke? on how to connect the other wires that go to the doors, trunk and other connections so the remote would work? where the wires are, how to identify each wire, how best to connect, etc?
@Viosified
@Viosified Жыл бұрын
Thanks for the input. I appreciate it.
@n54anaya79
@n54anaya79 2 жыл бұрын
Wow this was a nice process to watch. Great job & thank you!
@Viosified
@Viosified 2 жыл бұрын
Thank you so much :)
@LJ-xc7nu
@LJ-xc7nu 2 жыл бұрын
This is the best installation video ive seen thanks!!
@Viosified
@Viosified 2 жыл бұрын
Thanks so much!
@EyeAlone777
@EyeAlone777 2 жыл бұрын
Sir, your video is one of the best tutorial video ive seen, very detailed, clear and concise. Easy to follow and it encourages people to be self reliant or DIY. Thanks for sharing. I wanted to ask, i followed your all the instructions and have read the installation manual, i have noticed that whenever i am depressing the brake pedal, there were lights coming on in the instrument panel even i have not yet press the startbutton, or swipe the RFID kit. Is this nornal? I have connected the blue wire from the modulebto the green wire of the brake switch connector as per your video. However, those instrument icon is lighting up when im hitting the brake pedal. Please advise.
@Viosified
@Viosified 2 жыл бұрын
Hi sir, thank you for your feedback. Please re-check your wiring, there could be a mismatch somewhere. The instrument panel icons should only light up when you press the start/stop button (after swiping the RFID tags). Kindly check if the wiring to the ACC in the ignition harness is correct. Thanks 🙏
@EyeAlone777
@EyeAlone777 2 жыл бұрын
@@Viosified sir, it seems i was able to figure it out.. The wiring were matched but it seems that the blue wire going to brake switch had touched body ground. All good now. Thanks again for the response and help. Keep up the good work and more power on your upcoming vids. Hope you could do vid on how to install cruuse control to Toyota 2017 Vios E variant manual tranny.
@Viosified
@Viosified 2 жыл бұрын
@@EyeAlone777 Nice! I'm glad you were able to figure it out. Thank you again for your kind words 😊 Keep safe. God bless 🙏
@santhoshkumar-mm4dh
@santhoshkumar-mm4dh Жыл бұрын
Wonderful performance sir
@Viosified
@Viosified Жыл бұрын
Thanks so much!
@rickeybutcher8365
@rickeybutcher8365 Жыл бұрын
Thank you much... You make it looks sooooo easy...👍
@Viosified
@Viosified Жыл бұрын
Thanks for watching 😊
@rodneyjhackenflash4865
@rodneyjhackenflash4865 5 ай бұрын
Great video. After watching I ordered a kit off Amazon. It will be here this Friday. One question: Do I hook up the brake wire and leave the original male connector inside the brake's female connector of the brake assembly, or do I pull the male connector out of the female connector and leave it off? Thanks.
@Viosified
@Viosified 5 ай бұрын
Hey there. The answer to your question is: Hook up the brake wire and leave the original male connector inside the brake's female connector of the brake assembly. (In the video, I disconnected it just to get a better view of the wires for the camera, but I connected it again after tapping the push start module brake wire to the 12v power wire, so that the brake lights will still turn on when I step on the brake pedal) Good luck. Have a good one 🙏
@rodneyjhackenflash4865
@rodneyjhackenflash4865 5 ай бұрын
@@Viosified Thanks a million! I'll let you know how it turns out.
@Viosified
@Viosified 5 ай бұрын
@@rodneyjhackenflash4865 no problem. Good luck 🙏
@monggo9485
@monggo9485 2 жыл бұрын
Grabe sobrang detailed at ang linis..
@Viosified
@Viosified 2 жыл бұрын
Salamat po
@monggo9485
@monggo9485 2 жыл бұрын
@@Viosified keep it up po.sana ung keyless entry na details nyo din po sana
@Viosified
@Viosified 2 жыл бұрын
@@monggo9485 thank you po sa feedback & suggestion sir.
@nixnet83
@nixnet83 Жыл бұрын
Awesome! Thank you so much :)
@NotizLp3
@NotizLp3 Жыл бұрын
Great video! But what about the immobilizer module I know you stated your keys don’t have chips and don’t use i mobilizers is there anyway I would know if my 2000 Toyota Avalon has the immobilizer system would I need the immobilizer module sold separately to bypass it
@Viosified
@Viosified Жыл бұрын
One way to find out if your car has an immobilizer is, you wont be able to start the engine using a duplicate key. The immobilizer sensor ring is usually located around the ignition barrel (where the key is inserted) and connected to a wire harness. If your car has an immobilizer and you want to install a push start system, you can try and take the chip inside the original key and tape it to the immobilizer sensor ring itself to bypass the system. Sometimes just taping the original key near the immobilizer sensor works. Thanks for watching.
@Paddy.1981
@Paddy.1981 4 ай бұрын
Great vid! Very detailed and precise step by step. Could you please pop a link to where you have purchased the system? And also, ive seen the vids where guys switch the barrel to ACC position abd then remove the barrel. Is that a safe option? Additionally if theres an immobiliser, what do you do in that case? Many thanks
@Viosified
@Viosified 4 ай бұрын
Thanks for watching! Yes, removing the barrel is also a safe option. In case of factory immobilizers the common practice is to locate the chip inside the original key and tape it on or near the immobilizer antenna to bypass the system and use the transponder that comes with the push start kit as the main security/immobilizer. Here are links to the push start kit: ph.shp.ee/p9tG46v (Shopee) amzn.to/3Yuh9nF (Amazon)
@shivraj1006
@shivraj1006 29 күн бұрын
Very professional video. Sir Can u make a video on toyota aqua hybrid push start wires installation plz.
@Viosified
@Viosified 29 күн бұрын
@@shivraj1006 when the opportunity arises. Thank you for watching!
@Viosified
@Viosified 2 жыл бұрын
Push Start/Stop kit: goeco.mobi/4CEcXkH5 or, try this link to buy from amazon: amzn.to/3Yuh9nF
@azmimudamie6160
@azmimudamie6160 Жыл бұрын
Saya nak buat area mana
@kutonb
@kutonb Жыл бұрын
can you give the link of the products thanks and very detailed installation.
@Viosified
@Viosified Жыл бұрын
Thanks! Here's the link: goeco.mobi/4CEcXkH5
@kaiblas274
@kaiblas274 2 жыл бұрын
Ang husay po at madaling sundan tutorial nyo. Sayang ngayon ko lang napanood baka na encourage din sana akong mag DIY. Pinakabakit ko lang kasi PKE ko medyo mahal din binayad ko. Ask ko lang sir ano ang proper na pag start apak preno then pindot ba agad? Or pindot muna ng dalawang beses na magkasunod hanggang lumabas mga light indicator sa dashboard then apak preno then pindot ulit to start engine.
@Viosified
@Viosified 2 жыл бұрын
Pwede po na sabay na ang pag apak sa brake at pag press sa start button. No need to press twice. Salamat po sir.
@kaiblas274
@kaiblas274 2 жыл бұрын
Ah rekta na po? Hindi na idadaan sa mga acc? Ok po. Last question po sir pano ang pag pindot isang mabilis na pindot lang ba or medyo long press? Napansin ko kasi sa vios ko minsan pag mabilis na pindot medyo hindi nagtutuloy umandar. Kaya ginagawa ko medyo long press. Ano po ba dapat?
@Viosified
@Viosified 2 жыл бұрын
Opo rekta na sir. Sa pag start po, apak sa brake then i-long press nyo lang yung button hanggang mag start na po ang makina, then release.
@kaiblas274
@kaiblas274 2 жыл бұрын
Copy salamat po. New subscriber nyo po ako. Godbless
@Viosified
@Viosified 2 жыл бұрын
Salamat po. God bless!
@alexmarroquin4631
@alexmarroquin4631 11 ай бұрын
Thanks for the video very clear instructions 👍 I have a question is it possible to start it by jumping the cables ( hot wire)?
@Viosified
@Viosified 11 ай бұрын
It's a possibility
@alexmarroquin4631
@alexmarroquin4631 11 ай бұрын
@@Viosified ok thank you
@Hataku08
@Hataku08 2 жыл бұрын
Napaka detalyado po ng tutorial niyo. Salamat po, Ask ko lang po, san po dun sa tinestest light niyo malapit ang parklight wire? Ano po kulay? Plan ko po sana mag install ng steering wheel controls pero hindi ko mapagana ung illumination ng SW controls. Salamat po
@Viosified
@Viosified 2 жыл бұрын
Kung para sa SW controls pwede po sa ACC (accessory) wire. Yun po ang makapal na green wire na nasa gitna ng makapal na blue & red wires ng ignition harness (makikita po sa video, around 7:11 - 7:15). Salamat po.
@Hataku08
@Hataku08 2 жыл бұрын
@@Viosified hindi po ba parating naka ilaw if sa acc? 🙂 itrace ko po sana pag on ng parklight switch sabay illuminate na din ung SW controls. Maraming salamat po ulit sa pagsagot.
@Viosified
@Viosified 2 жыл бұрын
Mage-energize lang po yung ACC wire pag pinihit ang susi sa ACC, kung saan mago-ON din ang head unit. Isang option din po yung mapayat na violet Ignittion 1 wire na nasa ibaba ng makapal na green ACC wire. Mage-energize lang po ang Ignition 1 wire kung pipihitin ang susi sa "ON" position gaya ng nasa video. Ingat na lang po para di maputukan ng fuse. Good luck sir.
@jrbalingasa38
@jrbalingasa38 2 жыл бұрын
Ibrahim cali parehas tayo ng issue hindi ko rin alam paano paganahin at pailawin yung illumination ng SW na nabili ko sa LAZADA ano po balita na solve. nyo na po ba paano?
@jafladd
@jafladd 2 жыл бұрын
Great video! Did you have a chip key before you installed this system? I want to put it on a 99 Explorer but I a, worried it won’t work because of my chip key. I am hoping this does away with the need for it.
@Viosified
@Viosified 2 жыл бұрын
Mine doesn't have a chip but you can bypass yours by attaching one of the original chipped keys (or the chip itself found inside the key) to the immobiliser/sensor ring located somewhere near the ignition barrel using an electrical tape. This way you can start your car via the push button after scanning the tags on the transponder antenna that comes with the kit. Thanks!
@axenz1
@axenz1 3 жыл бұрын
Thankyou, very nice done.
@Viosified
@Viosified 3 жыл бұрын
Thank you so much :)
@radj4719
@radj4719 Жыл бұрын
Mate you're an absolute champion , fantastic video and detailed information , with the blue tag do you have to swipe everytime you start the engine also where did you position the transponder ring Can the blue tag be left permanently near the transponder ring Many thanks
@Viosified
@Viosified Жыл бұрын
Thanks! Yes I have to swipe the blue tag everytime I start the engine. I kept the transponder ring hidden under the dashboard. The length of the transponder ring cable allows you to hide it somewhere inconspicuous but still accessible for swiping. For safety reasons, it is not recommended to keep the blue tag permanently attached to the transponder ring. The blue tag serves as your security key against theft and unauthorized use; it also wakes up the ignition system when you need to start the car.
@radj4719
@radj4719 Жыл бұрын
@@Viosified thanks for the info , i have a 2014 Toyota yaris equipped with factory transponder/immobilizer , can this be fitted to it is there a way to somehow bypass it thanks
@Viosified
@Viosified Жыл бұрын
@@radj4719 Yes. You can "bypass" the factory immobilizer, but you either have to permanently attach the original key (with the transponder chip) near or onto the immobilizer sensor; or, you can crack open the rubber handle/body of the original key to access the chip inside and attach that chip near or onto the immobilizer sensor with a tape. Then you may proceed to install the third party Push Start Kit as demonstrated in my video.
@radj4719
@radj4719 Жыл бұрын
@@Viosified great info thanks again mate and much appreciated 👍🙂
@Viosified
@Viosified Жыл бұрын
@@radj4719 thanks for watching 🙂
@MrDrag110
@MrDrag110 Ай бұрын
I bought a second hand toyota vios 2014 car. it has already installed aftermarket keyless entry system. Do i have to buy a new set of keyless entry system with push start button? Or i will buy only the push start button and use the existing keyless entry system. ? Is it possible?
@Viosified
@Viosified Ай бұрын
@@MrDrag110 You don't necessarily have to buy a completely new keyless entry system if you already have an aftermarket one installed. It’s possible to just add a push start button & integrate it with your existing keyless entry system. However, compatibility between the existing system & the new push start button is key. You’ll need to check whether the push start button you plan to buy is compatible with your current keyless entry system or if any additional wiring or modules are needed to make it work together. Sometimes, aftermarket keyless entry systems can be adaptable, but it’s a good idea to consult a professional installer or technician to avoid any electrical issues or installation problems. If the existing system isn't compatible, then buying a new set (keyless entry + push start button) might be a better option to ensure everything works properly.
@nanotech4947
@nanotech4947 2 жыл бұрын
Hi. Your video is so good and easy to understand. Thank you! I want to ask whether or not the same procedure can be applied to Camry? I'm sure there will be additional steps since the Camry has immobilizer. I afraid if I DIY the alarm system, the engine won't start. Huhu
@Viosified
@Viosified 2 жыл бұрын
Hi. Yes the same principles apply for Camry, you just have to make sure the wiring of the ignition harness matches that of the Push Start kit (this is very important). As for the immobiliser, you can attach one of the keys (or the chip itself found inside the key) to the immobiliser ring in the ignition using zip ties or electrical tape to bypass the security. That way you can start the car using the transponder/immobilizer that comes with the Push Start kit. Thank you. I hope this helps :)
@nanotech4947
@nanotech4947 2 жыл бұрын
@@Viosified I've seen there are push start system that comes with alarm. They call it PKE (passive keyless entry). Does this system hard to install?
@Viosified
@Viosified 2 жыл бұрын
PKE is a little bit more complex to install than the basic push start system because there are other wires to connect to for the alarm and lights.
@nanotech4947
@nanotech4947 2 жыл бұрын
@@Viosified thank you bro. Really appreciate it!
@Viosified
@Viosified 2 жыл бұрын
Anytime :)
@orgelshoxha1259
@orgelshoxha1259 9 ай бұрын
Thanks for the video man , i got a question. I got a ford focus mk2 2009 manual transmission , does this work for my car? And where do i have to connect that wire that goes to the brake? Due to there is no need to press the brake and to start the car on the manual transmission, lol😂. Please let me know. Thanks matte
@Viosified
@Viosified 9 ай бұрын
You're welcome. 🙂 1st ques.: It will work provided the wires are matched correctly. 2nd ques.: You can connect it to the light switch in the brake pedal that triggers the tail light when you step on the brake. Thanks for watching.
@nak141
@nak141 2 жыл бұрын
Super neat wiring and nice vdo.
@Viosified
@Viosified 2 жыл бұрын
Thank you 😊
@francomartin5388
@francomartin5388 10 ай бұрын
Friend, I have a big doubt and a question if you can help me. My car has a remote start with an original factory key and I can start it remotely from my house with its key. I am going to use 2 keys with a chip, one for the chip that will always be placed in the ignition antenna (to be able to enable the button that I am going to install) and the other as a spare to be able to start the car remotely. My question is: will the copy of my other key with a chip work to start the car remotely from the house once the button and a permanent chip in the antenna are installed? Greetings
@Viosified
@Viosified 10 ай бұрын
It might not work, because the ability to start your car remotely using the original factory key and the remote start feature - as provided by your car's original equipment manufacturer (OEM) remote start system - is designed to work with specific components and protocols to ensure the security and proper functioning of the remote start feature. When you introduce a third-party push start and stop button with its own module and transponder sensor antenna (such as the one demoed in my video), you are essentially adding a new component to the car's electrical and security system which introduces compatibility issues. If you need the remote start feature I suggest you install the PKE version of this kit. I don't have a tutorial for that kit but it uses the same principles outlined in my video, with the exception of connecting additional wires to enable extra features. Most car accessories dealerships sell this type of kit and they can install it for you at no extra cost. Please note, however, that this third party kit will essentially take over and disable your OEM remote setup. I hope this answers your question. Thanks for watching. Have a good one!
@amjad98237
@amjad98237 11 ай бұрын
Useful video
@Viosified
@Viosified 11 ай бұрын
Thanks!
@drodessit
@drodessit Жыл бұрын
Hey how are you? I just wanted to find out if you can install push the start button can on the car that already has computer alarm and remote start.Thank you
@Viosified
@Viosified Жыл бұрын
It's possible but the wiring setup may differ based on how the alarm/remote start was installed.
@drodessit
@drodessit Жыл бұрын
Is there a way you can consult me on this im willing to pay for it
@drodessit
@drodessit Жыл бұрын
@@Viosified mine is connected through blade-al
@drodessit
@drodessit Жыл бұрын
O ты говоришь по русски
@drodessit
@drodessit Жыл бұрын
Oh im sorry I thought you speak russian then i saw you are from Phillipines. Can you just tell me one thing, on this push to start kit do i have to wire lock and unlock mandatory or i can only wire for engine start?
@markmacaraeg5312
@markmacaraeg5312 Жыл бұрын
Great it helps a lot thank you sir pls make a video of push start button w/remote..
@Viosified
@Viosified Жыл бұрын
Thanks for watching :)
@quoctran3510
@quoctran3510 Жыл бұрын
Hi men. Is it the same to set up on my Camry se 2023, do you have any instructions on Camry se 2023? Thank you!
@Viosified
@Viosified Жыл бұрын
Sorry, I don't have one for Camry but the steps are basically the same, just make sure to use a tester to match all the wires correctly.
@ncksncrl8856
@ncksncrl8856 8 ай бұрын
It is possible to use the switch in the clucth pedal. If the car has a clucth pedal instead of the brake pedal wire ?
@Viosified
@Viosified 8 ай бұрын
Yes, if that's a more convenient location for you.
@KCCLIP-s
@KCCLIP-s 3 ай бұрын
i love this vid imma install one soon but with the steering wheel lock cause i dont wanna make a duplicate key can i use my regular key put in the acc to prevent the steering lock and take it out???
@Viosified
@Viosified 3 ай бұрын
@@KCCLIP-s hey there. The key has to be kept inserted in the ignition (even in ACC position) to prevent steering wheel lock out while driving. Good luck!
@KCCLIP-s
@KCCLIP-s 3 ай бұрын
@@Viosified what happens if I put it in that position then remove?
@KCCLIP-s
@KCCLIP-s 3 ай бұрын
It doesn’t go back to off right?
@Viosified
@Viosified 3 ай бұрын
@@KCCLIP-s if you remove the key in any position the steering wheel will lock up while driving, you need to keep the key inserted in the ignition barrel to prevent that. That's the reason I had a duplicate key made then cut it to size so it can sit flush in the ignition barrel to prevent lock up. I hope this helps.
@KCCLIP-s
@KCCLIP-s 3 ай бұрын
@@Viosified oh thanks I thought putting it in on position then removing would be fine but thanks I don’t wanna have an accident
@eternalsenju3478
@eternalsenju3478 2 жыл бұрын
Nice. Which brand and model (Push start kit) would be best for a GM type car? And would it be compatible if i upgrade the key fob/rfid with those newer LCD remotes?
@Viosified
@Viosified 2 жыл бұрын
Thanks! The Push Start kit used in the video is a generic product and would fit most car brands as long as the kit"s wires and the car's ignition harness are matched correctly. The RFIDs for these products are uniquely encrypted for each module, and fobs or RFIDs from another manufacturer or brand may not be cross compatible (for security reasons).
@longtran-eb1hi
@longtran-eb1hi 2 жыл бұрын
Thanks you very good !
@Viosified
@Viosified 2 жыл бұрын
Thanks 😊
@MLK.PaNoRaMa
@MLK.PaNoRaMa Жыл бұрын
Where did u place the round transponder ring? just behind the push start button? not clear
@Viosified
@Viosified Жыл бұрын
I hid it somewhere under the dashboard. The cable is long enough so you can choose to install it in a discreet place but still accessible for you to swipe the blue tag.
@awakenedblacktivist7018
@awakenedblacktivist7018 Жыл бұрын
Can u put up a link for those 4mm spade connectors. Looked for them on eBay couldn't find them.
@Viosified
@Viosified Жыл бұрын
Hi there. Here's the link: amzn.to/40QKXfA
@awakenedblacktivist7018
@awakenedblacktivist7018 Жыл бұрын
Thanks
@XellosMetallium
@XellosMetallium Жыл бұрын
can yuu explain why you add a jumper to connect the two 12v constant wires together?
@Viosified
@Viosified Жыл бұрын
Because the push start module harness only has one 12v line, and the ignition harness has two. I decided to utilize both power sources by bridging them with a jumper connection. But that is just my preference.
@josephcarmelotes6051
@josephcarmelotes6051 2 ай бұрын
Is it applicable booth manual and automatic transmission?
@Viosified
@Viosified 2 ай бұрын
@@josephcarmelotes6051 Yes
@awakenedblacktivist7018
@awakenedblacktivist7018 Жыл бұрын
Also, I'm installing this on a 2010 Lincoln Town car. Do you think that the 4.8 Spade connectors will work or does it have to be 4mm?
@Viosified
@Viosified Жыл бұрын
Not so sure about the exact size for the Lincoln, but the link I gave you provides assorted sizes of spade connectors which includes both 4.8mm and 4mm, among other sizes. (Here's that link again: amzn.to/40QKXfA )
@awakenedblacktivist7018
@awakenedblacktivist7018 Жыл бұрын
@@Viosified Ok. Thanks again.
@Viosified
@Viosified Жыл бұрын
Thanks for watching
@awakenedblacktivist7018
@awakenedblacktivist7018 Жыл бұрын
@@Viosified No problem.
@dazharchives
@dazharchives 6 ай бұрын
can i use 4.8mm spade connector instead of 4mm? does it still fit?
@Viosified
@Viosified 6 ай бұрын
It won’t fit, but if it’s all you have you can still use it if you file it to size.
@Jamz_Ace
@Jamz_Ace 8 күн бұрын
sir paano eh key program ulit yong dalawang remote ng PKE keyless system (model XY-Q618 Hippcron).. ni reset ko kasi akala ko sira yong remote wala palang kasamang battery yong remote.
@rodneyjhackenflash4865
@rodneyjhackenflash4865 5 ай бұрын
Where can I buy the VIOS Gen 3? Can't find it on Amazon.
@Viosified
@Viosified 5 ай бұрын
Vios Gen 3 is the car model used in the demo, but you can try this link: amzn.to/3Yuh9nF if you're looking for the push start kit.
@NORMAGAYNILO-w1x
@NORMAGAYNILO-w1x Ай бұрын
Good day sir, what if the car has only one ignition wire, what i mean is there is only Ignition 1 and no Ignition 2?
@Viosified
@Viosified Ай бұрын
@@NORMAGAYNILO-w1x you can try connecting that to either IG 1 or IG 2 and test to see which connection starts the engine. You can also try combining the module's IG1 & IG2 and connecting them to the single ignition wire and then test if the engine starts. In case of any hiccups, I suggest you consult with a professional installer near you before proceeding to make sure everything is connected correctly.
@NORMAGAYNILO-w1x
@NORMAGAYNILO-w1x Ай бұрын
@@Viosified tnx sir, God bless
@BonziBonz
@BonziBonz 2 ай бұрын
Do i need to uninstall the keyless entry before installing this push start system? Tnx in advance and God bless
@Viosified
@Viosified 2 ай бұрын
@@BonziBonz whether you need to uninstall the original keyless entry before installing a similar aftermarket push start system shown in my tutorial depends on the specific kit & your car's existing setup. Some push start systems are designed to work alongside factory keyless entry, while others may require modifications or removal of existing systems to avoid conflicts. It’s best to check the specific installation instructions included in the kit you will use. And in case you encounter any technical hiccups, feel free to consult with a professional installer near you to ensure compatibility & proper installation. I hope this helps.
@janpatrick4811
@janpatrick4811 Ай бұрын
Sir would you know kung pwede na instead na yung button na kasama ng kit ang gamitin, yung orig toyota push button ang ikakabit? Para sana mas oem yung itsura? Thanks
@Viosified
@Viosified Ай бұрын
Pwede rin po basta tama ang wiring
@Tony-fn7cb
@Tony-fn7cb Жыл бұрын
Can this be done on a 2019 gmc Sierra 2500 HD?
@Viosified
@Viosified Жыл бұрын
Yes, just be sure to test and match the wires correctly.
@frederickwinchester
@frederickwinchester Жыл бұрын
Hey, my Toyota wish has a push start stop button installed aftermarket. But there are times when you can hear the relay but car does not trigger the ignition. Is there anything wrong with the circuit? P.s i’ve fixed my car starter but issues still persist
@Viosified
@Viosified Жыл бұрын
If the starter isn't problematic, check the health of the battery if it is strong enough to crank the engine. Also check the battery connectors if they're tight enough. Loose connections can cause starting issues. The old Push Start button, module, and/or its wiring could also be a factor and might need to be replaced if they are damaged or worn out.
@michaelmorada2257
@michaelmorada2257 Жыл бұрын
Pag may existing na na immobilizer at alarm, tatanggalin yung dati?
@KCCLIP-s
@KCCLIP-s 3 ай бұрын
Hey I came to do the install I got everything but then o can’t find my wiring harness I have a Holden Captiva 2011 and all I see are small little cables I tested them and it runs the test of constant 12 v but I’m not sure what I can do
@Viosified
@Viosified 3 ай бұрын
@@KCCLIP-s sorry for the late response. It sounds like you've made good progress with the installation, but identifying the individual wires can be tricky. Since you're having difficulty with the wiring harness and identifying the correct cables, it might be best to seek assistance from a professional installer or an auto electrician. They can ensure everything is connected safely and correctly, especially for a complex task like this. Your Holden Captiva 2011 may have specific wiring that a professional will be familiar with. Best of luck with the installation!
@KCCLIP-s
@KCCLIP-s 3 ай бұрын
@@Viosified hmm but I check all the cables and it’s connected to the steering column but a controller steering proportional is also connected to it I ran test light on the wire connected to the column it’s just smaller and does work with the accessories with the light going on
@KCCLIP-s
@KCCLIP-s 3 ай бұрын
@@Viosified does the ignition wiring harness have to connect to the steering column
@Viosified
@Viosified 3 ай бұрын
@@KCCLIP-s the harness is attached to the column so that they don't rattle and make weird noises while driving but you can detach them to make your setup easier and reattach them afterwards.
@KCCLIP-s
@KCCLIP-s 3 ай бұрын
@@Viosified oh ok cause I have harness but it’s like smaller then the regular so I’ll have to get smaller connectors
@Pawankumar-ei6ue
@Pawankumar-ei6ue Жыл бұрын
Thanks for the video, after installing I am unable to lock and unlock the car using remote (push start button is working fine) can you please help me?
@Viosified
@Viosified Жыл бұрын
This tutorial might help: kzbin.info/www/bejne/qZ3bkHyjpsh5hLs
@Pawankumar-ei6ue
@Pawankumar-ei6ue Жыл бұрын
@@Viosified Thanks for the quick response. It’s working ❤️
@Viosified
@Viosified Жыл бұрын
@@Pawankumar-ei6ue you're welcome 😊
@firdauszamani690
@firdauszamani690 2 жыл бұрын
Hi sir, how to connect if my car got two wire starter? Can it be loop together just like 12v wire?
@Viosified
@Viosified 2 жыл бұрын
If you're sure they both supply power to the starter then, yes.
@jmahachi
@jmahachi 2 жыл бұрын
Hello and thank you for your video. I have installed a similar product on my '98 Toyota Vista. I correctly identified all the wires and connected them to the original harness using T-tap connectors. My issue is that the car kicks but it won't actually start. If I put back the original harness (to the key), the car kicks and starts okay. Any ideas?
@Viosified
@Viosified 2 жыл бұрын
Hi. Try swithcing the position/connection of Ignition 1 and Ignition 2 wires and see what happens. Thanks
@jmahachi
@jmahachi 2 жыл бұрын
@@Viosified I'll try that when the sun 🌞 is up, thank you. I also noticed that you bridged the constant +12v. Is there a reason for that? Does the order/matching of Ignition 1 and 2 on the device matter?
@Viosified
@Viosified 2 жыл бұрын
Okay, good luck! It's because there's only one 12v wire in the push start module so I had to bridge the two 12v connectors in the ignition harness because they both supply current to essential components in the car. Yes, proper matching of Ignition 1 and Ignition 2 wires matter, otherwise the engine won't run. I hope this was helpful. Thank you :)
@jmahachi
@jmahachi 2 жыл бұрын
@@Viosified it's definitely eye opening. I'll be back with the results. Many thanks for taking the time to respond so quickly. Truly appreciated.
@Viosified
@Viosified 2 жыл бұрын
Thank you, hope everything works out :)
@Ariel1526
@Ariel1526 Жыл бұрын
I can't install on Hyundai i10. Is there any way to help? What connects to constant 12v?
@Viosified
@Viosified Жыл бұрын
Hi. You can find the constant 12v with a tester (the same goes for all the other wires as well). The constant 12v wire is energized even when the ignition is OFF. The kit also comes with an instruction manual that explains where to connect each wire.
@arisjobetodal3010
@arisjobetodal3010 3 жыл бұрын
thank you paps. ask ko lng, same set-up ba pag clutch start? o ilalagay sa clutch switch ung dapat na sa brake switch na connection. salamat in advance.
@Viosified
@Viosified 3 жыл бұрын
Hi sir. Sa brake pedal ko po sya ikinabit for added safety. Kaya pag magstart po ako apak ko ang clutch and brake pedals ng sabay. Salamat po. :)
@rizalmusa7273
@rizalmusa7273 2 жыл бұрын
I have install this stuff...can i push start/stop button only 1xtime/step the brake to start the engine?or mybe 2xtimes?
@Viosified
@Viosified 2 жыл бұрын
1 time is okay. Just step on the brake & press the push start button once to start/stop the engine right away. (You may also need to step on the clutch at the same time if yours is a manual car equipped with a clutch safety ignition switch).
@rizalmusa7273
@rizalmusa7273 2 жыл бұрын
@@Viosified ok thanks
@haramkhuram1561
@haramkhuram1561 Жыл бұрын
Thanks boss
@Viosified
@Viosified Жыл бұрын
Thanks for watching :)
@jay2617
@jay2617 2 жыл бұрын
Hello same lamg po ba sa vios dual vvti mag set up? Same wirings lng naman siguro po? Gen 3 2017 cvt
@Viosified
@Viosified 2 жыл бұрын
Opo sir
@KonaLokanadham
@KonaLokanadham Ай бұрын
Alto 800lxi me hoga please telme sir
@revolutionperminute208
@revolutionperminute208 Жыл бұрын
how does your steering wheel lock function?
@Viosified
@Viosified Жыл бұрын
The steering wheel lock is disabled when a key is inserted in the ignition barrel (that is the trade off with this set up).
@OfficialILLA
@OfficialILLA Жыл бұрын
Tried to test the brake wires but there is no room for me to test them and its impossible to get to them even if I removed everything possible, any suggestions?
@Viosified
@Viosified Жыл бұрын
One option is to visually follow the wire and find an accessible location to test it and/or splice it at that location (if possible). Second option is to use a hand-operated momentary button switch as an alternative to the brake pedal switch, but you have to connect it to a constant 12v power source. The 2nd option still retains the safety feature of the push start kit because of the momentary button switch.
@carpainter4179
@carpainter4179 Жыл бұрын
Is this for a manual car or a automatic gearbox?
@Viosified
@Viosified Жыл бұрын
It's applicable for both manual & automatic.
@carpainter4179
@carpainter4179 Жыл бұрын
@@Viosified is there a difference with connecting the wires to an automatic or a manual transmission?
@Viosified
@Viosified Жыл бұрын
@@carpainter4179 None
@revolutionperminute208
@revolutionperminute208 Жыл бұрын
if you don't put the cutted key would the steering wheel lock while driving
@Viosified
@Viosified Жыл бұрын
Yes, that is correct.
@erciodisergio
@erciodisergio Жыл бұрын
I have renault clio which already has a start stop button to start the engine. It doesnt have a key it has a card. You insert the card then start the engine. I bought from this set but don't know how to assemble it
@Viosified
@Viosified Жыл бұрын
Those kits usually come with an installation diagram & instructions and follow the same principle as shown in my video. However, if you don't feel comfortable installing one yourself you can find a car electrician to install it for you.
@erciodisergio
@erciodisergio Жыл бұрын
@@Viosified thanks for the answer. Yes there is a diagram and instruction. I will try, if I can't, I will have it done
@Viosified
@Viosified Жыл бұрын
@@erciodisergio ok, good luck on your project 👍
@kenkillernewlife85
@kenkillernewlife85 2 жыл бұрын
Ignition1 and Ignition2 look confuse can you explain about testing both 2 cable plz
@kenkillernewlife85
@kenkillernewlife85 2 жыл бұрын
How can we know which one is Ignition 1 and 2 ?
@Viosified
@Viosified 2 жыл бұрын
@@kenkillernewlife85 Test probe light flickers as you crank the engine = ignition 1 Test probe light becomes dimmer (or turns off) as you crank, and turns on again after cranking the engine = ignition 2
@adabogs4589
@adabogs4589 2 жыл бұрын
salamat sir gawa ka naman ng tutorial for installing alarm sa vios gen 3 idol :)
@Viosified
@Viosified 2 жыл бұрын
Pag may chance po sir :)
@adabogs4589
@adabogs4589 2 жыл бұрын
@@Viosified salamat sir aabangan ko yan salamat sa mga videos mo sobrang linaw sarap panoorin
@Viosified
@Viosified 2 жыл бұрын
@@adabogs4589 maraming salanat po sir :)
@josephcacayan8667
@josephcacayan8667 Жыл бұрын
What if the connection to the brake transfered to the clutch? Then i dont need to step on the brake?
@Viosified
@Viosified Жыл бұрын
Yes, you can do that, but stepping on the brake pedal (in addition to the clutch pedal) while starting the car offers additional protection against unintentional forward or rearward movement of the vehicle when on incline or uneven road surfaces.
@revolutionperminute208
@revolutionperminute208 Жыл бұрын
Does that kit kave remote start?
@Viosified
@Viosified Жыл бұрын
None
@cansinoqurtanthonyp.4677
@cansinoqurtanthonyp.4677 Жыл бұрын
How about the original key immobilizer how do you bypass it
@Viosified
@Viosified Жыл бұрын
If your car has an immobilizer and you want to install a push start system, you can try and take the chip inside the original key and tape it to the immobilizer sensor ring itself to bypass the system. Sometimes just taping the original key (or the chip inside the key) near the immobilizer sensor works as a bypass. Thanks for watching.
@bryandoculan89
@bryandoculan89 Жыл бұрын
Sir pwede request sa vios xle AT mo naman ikabit. 🙂
@Viosified
@Viosified Жыл бұрын
Pag may chance po, pero exact same steps lang po sya sa AT and MT, regardless of generation or model 😊
@jimmuelludovice3533
@jimmuelludovice3533 2 жыл бұрын
i have the same push start kit but i don't know how to install it. can you install it for me? willing to go to your shop or place. thank you
@Viosified
@Viosified 2 жыл бұрын
Sorry, I won't be able to install it for you, but my video is detailed enough to guide you through the steps of the installation.
@jimmuelludovice3533
@jimmuelludovice3533 2 жыл бұрын
@@Viosified ahh okay po ask ko lang po applicable din po ba ito for toyota vios gen 3 na matic?
@jimmuelludovice3533
@jimmuelludovice3533 2 жыл бұрын
@@Viosified and also po yung sa constant +12v po na jumper needdin po ba itest yung gagamiting wire para dun sa jumper?
@Viosified
@Viosified 2 жыл бұрын
Opo sir
@jimmuelludovice3533
@jimmuelludovice3533 2 жыл бұрын
Boss nakabit ko na po pero pag sa 3rd na pindot na po kahit nakatapak nako sa brake ayaw padin po mag start. Ano po kaya ang problema pag ganun po
@emiliob.854
@emiliob.854 2 жыл бұрын
Sir, may idea po ba kayo sa trigger ng toyota avanza sa central lock, confuse po kc ako sa trigger nya kung positive or negative tnx po
@Viosified
@Viosified 2 жыл бұрын
Not sure po sa Avanza, pero pwede nyo po gamitan ng multitester o test probe para malaman polarity nya, sir.
@markrodolphmojico7483
@markrodolphmojico7483 Жыл бұрын
Sir can you teach me how to locate the side door connection
@jay-arjavier9098
@jay-arjavier9098 2 жыл бұрын
Boss pano pag sa batman na manual sa break parin ba ikabit yung sensor o sa clutch
@Viosified
@Viosified 2 жыл бұрын
Kung saan po mas convenient sayo sir. Yung sakin sa brake light switch ko ikinabit yung payat na blue wire para dalawa ang safety (1. yung original clutch ignition switch at; 2. yung sa brake pedal para sa push start/stop kit).
@nathanielkennethtan6262
@nathanielkennethtan6262 3 жыл бұрын
Pwde po kaya jn sir ung female na 8pin connector pra ms mgnda tignan salamat very nice video
@Viosified
@Viosified 3 жыл бұрын
Pwedeng pwede po, magandang idea po yun. Thank you sir :)
@nathanielkennethtan6262
@nathanielkennethtan6262 3 жыл бұрын
Question lng dn po sir ok lng po kya n hndi na e balik ung socket pin dun s orginal position nya mostly kc ng nppnanuod ko iniisplice nla e..kpg na try m sir ung 8pin n female pa send nmn po ng link mern kc ako nkta s lazada d k lng sure kung same size sila pero 8pin dn eto p ung link sir pa comment nmn kung psok kya to o hndi salamt
@Viosified
@Viosified 3 жыл бұрын
@@nathanielkennethtan6262 Ok sir pasend nalang po nung link sa 8-pin connector, tingnan ko sya. Tsaka hingi din po ako ng clarification sa unang ques, alin pong socket pin yun sir, yung female spade/pin po ba na nasa loob ng male ignition connector?
@nathanielkennethtan6262
@nathanielkennethtan6262 3 жыл бұрын
Ung male pin po mismo sir kung ok lmg na d na e balik dun s dting socket na female wla nmn po cguro mggng prblem..
@Viosified
@Viosified 3 жыл бұрын
Kung tama po pagkaintindi ko sa ques, wala naman po problema yun ang mahalaga po ay tama ang wiring ng ignition sa push start module. Liban lang po kung gusto nyo ibalik sa dating nyang itsura at set up na de-susi :)
@shicobatshicobat5015
@shicobatshicobat5015 7 ай бұрын
please my brother is the jumper is important to make it
@Viosified
@Viosified 7 ай бұрын
It is optional.
@revolutionperminute208
@revolutionperminute208 Жыл бұрын
does your steering wheel lock remain function?
@Viosified
@Viosified Жыл бұрын
Yes. That's why I inserted a pre-cut duplicate key in the ignition barrel to prevent steering wheel lock-up while driving.
@guitarninja2098
@guitarninja2098 Жыл бұрын
@@Viosified ask ko lng sir kung hindi b ma drain ung battery kung lagi naka on ung susi?
@Viosified
@Viosified Жыл бұрын
@@guitarninja2098 hindi po madedrain ang battery dahil idi-disconnect po ang wire harness ng ignition barrel pag iseset-up na ang push start kit
@guitarninja2098
@guitarninja2098 Жыл бұрын
@@Viosified so nung kinabit nyo na ung wires from unit,hnd npo ibabalik ung ung ignition harness?
@Viosified
@Viosified Жыл бұрын
@@guitarninja2098 hindi na po sir, kasi dun po sa ignition harness ikakabit yung mga wires ng push start kit
@slik4mg
@slik4mg 3 жыл бұрын
What is the link to purchase this product?
@Viosified
@Viosified 3 жыл бұрын
Hi. Here are links to this product: shp.ee/63kk6zx?smtt=0.0.9 shp.ee/epqux67?smtt=0.0.9
@marlonsantos2356
@marlonsantos2356 3 жыл бұрын
vios din po ba sasakyan mo? matic po ba? matagal n po ba kau mekaniko?.salamat god bless
@Viosified
@Viosified 3 жыл бұрын
Opo. Manual po. God bless..
@redemeindangan2770
@redemeindangan2770 2 жыл бұрын
May nabili akong sasakyan na converted na to push start. Pwede po bang ibalik ito sa original at paano po, thanks
@Viosified
@Viosified 2 жыл бұрын
Pwede po sya ibalik sa dati, pero kailangan nyo po yung mga parts (ignition barrel, wire harness, etc.) na inalis nung dating may ari.
@carlpablo7631
@carlpablo7631 3 жыл бұрын
Hi Sir ang huyas po nnyo👌 Sir tanong po ano different po ng ignition1 and 2 po? Kasi po mag-install ako water temp sa Vios gen3 ko po mayroon nakagay ignition connection di ko sure po San iconnect ignition 1 or 2 or same lang po sila? Salamat po.
@Viosified
@Viosified 3 жыл бұрын
Hi sir. Magkatulong po ang ignition 1 at ignition 2. Mas priority lang po ng ignition 2 ang fuel pump, injectors, ignition coils, ECU, etc., o lahat po ng mga parts na kailangan para umandar ang makina sa start-up. Connected naman po ng ignition 1 sa iba pang mga circuits na kailangan para mapanatiling "buhay" ang sasakyan kapag nag start na ang makina. Pwede nyo po ikabit sa ignition 1 ang water temp guage nyo. baka makatulong po ang info na shinare ko sa video tungkol sa ignition wiring. Salamat po.
@carlpablo7631
@carlpablo7631 3 жыл бұрын
@@Viosified Maraming Salamat Sir sa detailed Info po. Update ko sir after mainstall👌God Bless Always🙏
@Viosified
@Viosified 3 жыл бұрын
@@carlpablo7631 Welcome po sir. Salamat din po & God bless 🙏
@carlpablo7631
@carlpablo7631 3 жыл бұрын
Hi Sir thank you po sa video nnyo VIOS Smart Start System at sa shared details info nainstalled and working na Water temp gauge. NagSubscribed nko po. Thumbs up👌
@Viosified
@Viosified 3 жыл бұрын
@@carlpablo7631 Good job sir 😊 👍 Salamat po sa update at salamat din po sa tiwala at supporta. God bless! 🙏
@alfredoperandos3958
@alfredoperandos3958 3 жыл бұрын
Sir maganda subukan project nato, may link po kayo kung saan nyo naorder ang kit?
@Viosified
@Viosified 3 жыл бұрын
Opo sir, dito ko po inorder: shp.ee/63kk6zx?smtt=0.0.9 shp.ee/epqux67?smtt=0.0.9
@alfredoperandos3958
@alfredoperandos3958 3 жыл бұрын
@@Viosified Thank you po! May kaibahan po ba ang isntllation sa manual at auto?
@Viosified
@Viosified 3 жыл бұрын
Wala po sir. Same lang po basta pareho ang ignition harness
@alfredoperandos3958
@alfredoperandos3958 3 жыл бұрын
@@Viosified thank you very much sir!
@Viosified
@Viosified 3 жыл бұрын
You're welcome sir :)
@lawrencegrancho8594
@lawrencegrancho8594 2 жыл бұрын
sir pwede po ba yan sa isuzu elf?
@Viosified
@Viosified 2 жыл бұрын
Pwede rin po basta tama ang set up ng wiring
@marlonsantos2356
@marlonsantos2356 3 жыл бұрын
sir tanong ko lng po.lilinisin ko sana un vvti solinoid ng vios ko 2011 .ang tigas sir ayaw mahugot.tapus dnala ko sa isang mekaniko hindi rin nyan mahugot.baka daw maputol.anu po kaya ang magandang teknik para matanggal ko para linisin na hindi maputol?
@Viosified
@Viosified 3 жыл бұрын
Sir pag po ayaw na mahugot pwede po buksan yung valve cover para ma-access yung solenoid mula sa ibabaw at maitulak palabas. Pero kailangan gamitan ng pangtulak kasi medyo tago yung solenoid. Kung abot, sungkitin po muna yung nanigas na sludge at tiktikin unti unti yung dulo ng solenoid papalabas para di mabali.
@pamkaturi
@pamkaturi 2 жыл бұрын
Parts kit number?
@Viosified
@Viosified 2 жыл бұрын
None. It is univ.ersal.
@yuvrajkshatriya6841
@yuvrajkshatriya6841 2 жыл бұрын
Where can I get it installed in Hyderabad?
@Viosified
@Viosified 2 жыл бұрын
Sorry I'm not familiar with the area, but if you can purchase it online maybe you can install it yourself using this video as a guide.
@yuvrajkshatriya6841
@yuvrajkshatriya6841 2 жыл бұрын
@@Viosified hi brother, i need some expert lik u to instal, becoz it's nt dat easy as it looks.i tried, bt not able to get the child lock connected. So do u hav anyone in Hyderabad?
@Viosified
@Viosified 2 жыл бұрын
So sorry my friend. I don't know any mechanic in Hyderabad that I could recommend. I hope you find a good one soon. 🙏
@yuvrajkshatriya6841
@yuvrajkshatriya6841 2 жыл бұрын
@@Viosified i re searched with many car decor people and spent hrs of time with dem. Dey were unsuccessful and spoiled da car dashboard. So disappointing. Seriously feeling very bad like y did i purchased it in da first place. Coz I cannot return it.
@Viosified
@Viosified 2 жыл бұрын
@@yuvrajkshatriya6841 perhaps you can try the services of an auto electrician to install it in your car. I hope you find a good one in your area.
@nazerisuib34
@nazerisuib34 2 жыл бұрын
where you buy it..share link please
@Viosified
@Viosified 2 жыл бұрын
Hi. I bought it here: shp.ee/epqux67?smtt=0.0.9. I don't know if you can access this, but you can try. Thanks!
@hakeemkyrie
@hakeemkyrie 3 жыл бұрын
pwede po ba yan sir sa toyota innova J 2018? salamat!
@Viosified
@Viosified 3 жыл бұрын
Good day sir. Sorry po, di ko pa nasubukan sa Innova, pero pwede mo po icheck ang set up ng ignition harness nung Innova kung pareho po ng nasa video. Kung magkaiba, pwede mo po gamitan ng tester o test light para ma-identify ang mga wires ng ignition harness. Yung mga wires ng push start kit po ay universal, pareho lang po sila ng nasa video. Salamat po.
@automoto747
@automoto747 Жыл бұрын
Pwede ba pa install Sayo? Magkano?
@seanelijahbautista579
@seanelijahbautista579 2 жыл бұрын
Sir anung ggamitin sa pag unlock and lock ng sskyan yun parin bang lumang susi? Tnx in advance
@Viosified
@Viosified 2 жыл бұрын
Opo sir yun pa rin :)
@Viosified
@Viosified 2 жыл бұрын
Opo sir yun pa rin :)
@jayson8214
@jayson8214 2 жыл бұрын
Question po sir. Ok po lahat ng wirings. Tested dn po. Pero pag i stop ko na yung car. Ayaw po mag off nung ilaw nung push button. Nagooff naman engine.
@Viosified
@Viosified 2 жыл бұрын
Kung tama po ang wiring, normal po na pag in-off nyo na, nagbi-blink yung push button for 1-2 minutes tapos kusa na din po mago-off yung ilaw ng push button. Ganun po ang design nya para in case kailangan nyo uli i-restart ang makina, may 1-2 minutes window na di na kailangan ire-scan yung RFID to start the engine.
@jayson8214
@jayson8214 2 жыл бұрын
Salamat sir. Try ko ulit kabit sa weekend.. tinanggal ko ulit. Haha. Baka kasi ma discharge battery.
@Viosified
@Viosified 2 жыл бұрын
@@jayson8214 basta tama po ang wiring di po madidischarge ang battery. Sige sir, good luck 😊
@real_ahmadkamal
@real_ahmadkamal 3 жыл бұрын
Can i use it on Gen 1?
@Viosified
@Viosified 3 жыл бұрын
Yes sir. Kindly check the wires of the ignition harness first to see if they are the same color and set up as the ignition harness shown in this video. If not, please make sure to test the wires individually to make sure they match the wires of the Push Start/Stop module correctly. Thank you :)
How to Install Push Button Start in your Car
9:15
Strange Garage
Рет қаралды 725 М.
How to: Full passive keyless entry install (project st220)
39:06
Chazz Coombes
Рет қаралды 86 М.
Когда отец одевает ребёнка @JaySharon
00:16
История одного вокалиста
Рет қаралды 16 МЛН
НИКИТА ПОДСТАВИЛ ДЖОНИ 😡
01:00
HOOOTDOGS
Рет қаралды 3 МЛН
Каха и лужа  #непосредственнокаха
00:15
К-Media
Рет қаралды 4,8 МЛН
Install Push Start button in any car at Home | DIY | Telugu
14:26
AutoFix - Telugu
Рет қаралды 490 М.
The Right Way to Install a Start Stop Button (EASYGUARD EC004)
13:57
The Auto DIY Guy
Рет қаралды 190 М.
Pemasangan Start Stop Engine Keyless Di Mobil
46:00
Fauzan Project Creative
Рет қаралды 178 М.
How install Keyless entry on 2001-2004 tacoma for only $14 in 10 minutes!
16:20
Overland Under Budget
Рет қаралды 38 М.
how to bypass immobilizer to install start/stop remote keyless
9:01
Best of my experience
Рет қаралды 114 М.
RFID Push Button Start Install | Mazda Mx3 - All Motor Project
18:24