Lucky the flywheel housing didnt crack. Just finished replacing a cracked flywheel housing. Had a clutch replaced about 6 months ago by some other shop. top 4 bolts were loose. 1 of which was found in the ECA guard. crap job too. was in a CNG fueled volvo with a ISX12. Found out the housing on a ISX12 is much worse to install than a isx15
@rhodes2you6 ай бұрын
Please refer to Eaton manual clsm0200. Anytime there is a possibility of engine housing damage the runout should be checked. Make sure to lube the cross shaft and use the proper alignment tool when installing a clutch.
@nabils65932 жыл бұрын
Judging from the fork repetitive action TCM doesn't see the shaft stopping which is due to clutch brake piece missing/broken. I have not worked on autoshift only manual transmission. My analysis is based on visual comparison. Just my input since there's no narrative in the video. Hope this helps you. 🤟
@lionsdejudah2 жыл бұрын
I added a detailed explanation in the description, it’s like no body reads anymore.
@anytimetnt Жыл бұрын
@@lionsdejudah *Nobody* It's like nobody has correct grammar anymore.
@Lento_MontarАй бұрын
Does this problem cause a truck to lurch/ jump while backing like all of a sudden it accelorates on its own
@LeonardoRodriguez-ji6jd9 ай бұрын
I have a problem with my automatic transmission, it hits only once when it slows down, its sound is similar to a clutch but it is new.
@sultonbekikromov59643 жыл бұрын
Was anything with clutch?
@thegreekguyviva-greece58812 жыл бұрын
Dialog..... ok..... if yall read the description it's all there. The noise is important if he talks over it you lose that diagnostic part for anyone watching trying to find a solution.. be nice people and read before yall yell dialog dialog.....
@Thedieseltechpro4 ай бұрын
Has anyone dealt with these inertia brakes coming apart?
@joshuahenderson95214 ай бұрын
yes, i just did one on one of these because it was in pieces in bellhousing. Too much play in input shaft caused it for me
@jerrymedellin73032 жыл бұрын
The clutch has any problem??
@rickl70243 ай бұрын
Yes ,,, I’ve done three clutches with this transmission setup,,, what happens is the springs in the clutch will brake,, then usually get jamed in the front clutch causing it not to disengage,,, trans ecm sees no disconnect , it sets codes then no gear engagements
@christopherarroyo69052 ай бұрын
@@rickl7024 I’m guessing a code 27
@almed96192 жыл бұрын
Looks like something is missing on throw out bearing
@sultonbekikromov59643 жыл бұрын
Was anything wrong there?
@oldschoolrodz97452 жыл бұрын
well the inertia brake is clearly not working for one.
@brkbt9311 ай бұрын
worn clutch brake looks like to me
@max1chase1662 жыл бұрын
Where is the dialogue to show what is being presented, to me it looks like the clutch is wayyy out of adjustment to stop the output shaft from spinning but you must tell us. Visual effect is great but no dialogue.????
@lionsdejudah2 жыл бұрын
Read the Description...
@rivera75nesto2 жыл бұрын
Kool
@neryrezabala32812 жыл бұрын
Tengo problema de falla ,cuando muebo marcha me pedorrea y despaciosa deltra el camvio ,este problema es cuando boy a salir o meter rebersa
@lionsdejudah2 жыл бұрын
What fault codes are you getting? Is your cab a KW?
@brunoeliasdiazchacon34895 ай бұрын
El mío me hace lo mismo que el tuyo ,acaso es que la transmisión no sirve ya
@eloyclaude21012 жыл бұрын
🤔
@sultonbekikromov59643 жыл бұрын
Wrong *
@JoseMartinez-ll7vo2 жыл бұрын
Need dialog!! I didn’t look up a KZbin video to read!!!