You naiked !Helped me immensely. First video I found that showed me exactly what I needed to know ! Thank you , I'm now a dedicated subscriber.
@zeblang9660 Жыл бұрын
Thank you for this video. It helped me finally fix my 770t. Echo replaced my entire engine but not the carb. Even after that it was still bogging and running hot. I kept telling them it was too lean and always told carb was set right. About a half turn and it runs like a hero. No more bogging and it doesn't smell like it's overheating. It smells like a 2 stroke should! And it has a noticeable amount more power. Thanks again for the information!
@garygore15 жыл бұрын
Thanks - just did this and solved my problem. Got a good set of the tools on Amazon for about $15. Appreciate the help.
@jonquillawnlandscape84915 жыл бұрын
ggnoodles1 broke the factory tool set and bought another off amazon. These blowers need slight adjustment from time to time
@Ebaybow2 ай бұрын
I got my Echo 500H running great today!
@dandylawnandmaintenance44075 жыл бұрын
I am going these tools and try this thanks. Also thanks for the trimmer video. I am not even going to tell you how many trimmers I have sold and bought new again just because I never knew. Thanks again.
@packmanbrosefreind87436 ай бұрын
Thank you I just been working. And just replaced the filter work again 😊
@patosborne0073 жыл бұрын
The current # for that tool is: Echo Walbro ECH-91159L but it can't be had cheap. AliExpress sells similar for under $2 but it's too short. If you buy one of those multi sets of drivers, the metal section needs to be at least 4" long or poss. loose your warranty & enlarge the hole to get closer to the carb. I do not know if one of those multi sets has a micro D that fits! YOU CAN MAKE ONE as I just did for .50 Ace Hardware, find the selection of tension pins, get the smallest, 5/32 x 1, not shortest; close it's gap & you have to grind it thinner BUT THIS is the only metal that is still strong enough to do the job. I put the pin in a vice so I could pound something into other end to make it long enough (Use long thin flat head) I tried everything before this as I won't give Echo (on line for $19.04 + 5.98 shipping) that much $. ***ALSO *** E-bay sells China carbs for the 770 for $15!. I saw a vid & it looks easy & worked great (so far) & HAS A FLAT HEAD ADJ. SCREW!!! I hope I've helped you as I banged my head for the longest. (edit: in my exp. all used blowers are slowed- down by a clogged spark arrestor. it's a screen at the exit of the muffler that 2 cycl oil has clogged. Throw this useless screen away BEFORE anything else!) I'M NOT SURE I even recommend this anymore b/c this tiny adj. screw is real stiff to keep from vibrating out of adjustment & it is tiny. My system might round it off so MAYBE replacement w/ a Chinese carb w/ a flat head adj screw is better LISTEN: The BIGGEST, BIGGEST improvement one can make is to lengthen that short blower tube. Being short (5' 8") I just unscrewed both tubes & connected them about 2" into each other then used strong black tape. If you're taller, you may need to order an extra section & fabricate. The end of the tube should be 2-3 feet away from your feet with no hands on. I AM NOW RARELY USING full power so: longer life more satisfying performance! One last clue. If you're adjusting any 2 cycle carb that has a slow adjustment, do not touch that adj. screw.
@kennyplay59823 жыл бұрын
Great ideas!!
@patosborne0072 жыл бұрын
@@kennyplay5982 Thank you!
@patosborne00710 ай бұрын
Looks like a 5/64 tension (get the longest @ Ace Hardware) will fit onto the carb adjustment. First use penetrating oil on the tiny adjustment stem. Echo stop selling any adjustment tool. Open just a hair! Do nothing else but there are clues in my other posts here. (find that pre air filter etc)
@chrisspears64015 жыл бұрын
Great Video, going to try changing the basics first. Thank you!!
@DanbyDoo4 жыл бұрын
Through and well presented tutorial. Thanks for the training ! Much appreciated. I’m going to have at it !
@jonquillawnlandscape84914 жыл бұрын
Daniel Dwyer good luck. Should work out for ya.
@ugna27735 жыл бұрын
Thx buddy. But when you adjust carb you should have the filter on. Makes a difference with the air mixtures
@jimziogas89783 жыл бұрын
Good job on this dude. Well explained
@banjoman6223 Жыл бұрын
Great job on the video very helpful
@jr_da_great240329 күн бұрын
You got a link to the tools i can use other then these blue ones?..i heard you said you,you broke the long one an order another one also is the short one needed
@LawrenceL10004 жыл бұрын
You’re a “PIMP”!!!! You rock bro! Does the 580 adjust this way also? I just picked up a used one and I want to go thru and make sure it runs like it should.... SUBSCRIBED!!!
@jonquillawnlandscape84914 жыл бұрын
Lawrence Lightner not 💯 but should be similar
@chrisgraham290410 ай бұрын
2023 Everybody now lists these tools as "Discontinued" or "No longer available".
@AvenueD41725 күн бұрын
Of course, this is a scam for these repair shops. They know these do it yourselfers don’t know shit about adjusting these carbs. These people drop off their machines and get charged a lot of money for something so minuscule
@jmmcdon252 жыл бұрын
Thanks for the great video!
@travissmith67755 жыл бұрын
Excellent video. Thanks for posting. Going to get online and buy that long d tool. Pretty sure this is my problem.
@laurencelangley18823 жыл бұрын
Thank you. Great video!
@patosborne0072 жыл бұрын
GOOD NEWS: Echo 91186 for only $11 is the adjustment STEM ONLY B U T if you squirt some spray oil in the hole where the (very stiff) carb adjustment is, it becomes much easier to turn. That is what was actually needed. I believe the 50 cent tool will work now! Just open it a TINY bit & FORGET IT otherwise you'll get lost trying to find the sweet spot. Don't skip the last paragraph below.
@petev55454 жыл бұрын
Hey guy, great video. Thanks
@lh984 жыл бұрын
I have a 770 same issue. Watched your video and made the adjustment and it worked, problem is I have to keep adjusting it over and over. (The high side jet) Is it loose shaking itself out of spec each time?? Legit have to adjust it every time I use it and sometimes while using it! Any insight on that sir?? Thanks
@ozenterprisesllc90212 жыл бұрын
Hi! I have a 500T. It sat for several years. SO, I replaced the carb, fuel filter, spark plug; and the fuel, of course, adding a touch of Seafoam. It started right up; but wouldn’t maintain idle, snd then wouldn’t te-start. I found the coil resistance way too high. I’m surprised I got any spark at all. I replaced the coil. Now, it starts right up on full choke, snd idles beautifully with the choke off. When I go to increase the throttle;however, it wants to cut out - lower the throttle and it returns to idle. The most I can give it is half throttle. Would this be the high adjustment? Which way do I go with it, if so. I don’t have the adjustment tool. Some on KZbin use a flattened roll pin.
@patosborne007 Жыл бұрын
The air filter has a foam pre-filter hidden behind the plastic retainer! I use Dawn then squeeze the f out of it
@foreverandaday81852 жыл бұрын
Does the 770 have a spark arrestor that's cleanable? If so, Id check that too if boggy
@halleffect14 жыл бұрын
is there high and low needle adjustments on these? if so, how do you tune the low needle? also, factory settings like number of turns on both needles would be helpful.
@kennyplay59823 жыл бұрын
Yes, isn't there a 2nd adjustment? Other than idle
@jimmiller63286 жыл бұрын
Thank you, very helpful.
@bradbanks627411 ай бұрын
Mine only starts at high rpm. It will not idle at all and seems to only have one speed (high) will this adjust it with only the high side adjustment?
@keny77974 жыл бұрын
My Echo 770P works Great for the first half tank of gas.After that it wont take full throttle and bogs down.Also, it wont turn off.I have to pull the cap off spark plug to turn it off.After sitting for a hour it runs great again; but still wont shut off.It use to shut off the last couple time i used it.Any suggestions on these problems.
@joej.41706 жыл бұрын
Doesn't counterclockwise richen the mixture and clockwise lean it out?
@jonquillawnlandscape84916 жыл бұрын
Joe Jirak correct
@travcon83 жыл бұрын
Is there a plastic cap over the adjustment screw?
@michaelcassidy34404 жыл бұрын
Do you possibly have a link for those carb adjustment tools? Thank you!
@johnhinkle32676 жыл бұрын
You showed the tools you bought online the blue d shaped ones but didn’t you use the black one that you had on that table to adjust the carb that’s what it looked like when I was watching the video it kind of trew me off since I found the blue tool online but wasn’t sure if it was the right one
@reallybadaim1185 жыл бұрын
Awesome video bro. Thanks
@stevesmith87675 жыл бұрын
just bought a 775 2 days old, used it 20 mins after taking a break, now wont start period... GAS\oil mixture is fine as this is being used in various other tools.
@davidpham37873 жыл бұрын
What tool are you using. Can I have the link or name of the item?
@user-rc8sq8en2w Жыл бұрын
PB-770H
@shawnurland16393 жыл бұрын
Have 770t new carb running fine then 2 weeks later bogging our again tried adjusting as per your video no change. New carb. New plug. New fuel filter clean air filter. Any other ideas? Thanks
@Jonathanaymond3 жыл бұрын
Try new gas?
@fluke13872 жыл бұрын
Mine dies on idle is there a idle hole and screw
@paddyslawnandleaf26315 жыл бұрын
Thanks for the video.
@franciscosanchez85753 жыл бұрын
what can I do my whip does not come out does not start the same sun
@demolaj12 жыл бұрын
so is it micro d ?
@viakion21252 жыл бұрын
lol my echo dealer didnt fix mine thats why im here
@salikovalexandr54668 ай бұрын
Подписка бро
@HardscapePro4 жыл бұрын
Hey where did you get those screwdrivers to adjust the RPM of your blower
@two9s6494 жыл бұрын
Lmao
@leftylion8164 жыл бұрын
I have a Echo PB755ST. I'm seeing some sticky black sludge at the exhaust port. What is that and why am I getting this issue? Thanks!
@jonquillawnlandscape84914 жыл бұрын
RAS BKLion probably just carbon from combustion. Just keep an eye on exhaust. Carbon will eventually blue up spark arrestor
@leftylion8164 жыл бұрын
@@jonquillawnlandscape8491 Thank You!
@Ozzylawncare4 жыл бұрын
I have a 770 works good for like 25 minutes and if i push the gas again it cuts off any idea whats issue with this blower
@kennyplay59823 жыл бұрын
What did you find out? I have the same problem.
@ektorcolon73685 жыл бұрын
trhanks for the video. !!!!!!!!!!!!!!
@dorrellmyles99952 жыл бұрын
👍👍
@JosueRamirezBarraza6 жыл бұрын
Do you turn clockwise or counter to rev it up more
@jonquillawnlandscape84916 жыл бұрын
Josue Ramirez counter clockwise adds more fuel
@5881585 жыл бұрын
my blower will only run with the choke set half way. it was stored over the winter with fuel in the tank . could the problem be old fuel?
@kennyplay59823 жыл бұрын
Did you use any type of Stabil in the gas?
@5881583 жыл бұрын
@@kennyplay5982 yes
@105OUTLAW13 жыл бұрын
@@588158 get a carb rebuild kit. 9/10 times it's a bad carb diaphragm.
@stephenP19796 жыл бұрын
Do you ever take the spark arrestor off? If so, does it make a big difference as far as running better?
@jonquillawnlandscape84916 жыл бұрын
S_J_P I never have. Some people do a say it performs better without it. I leave it on for safety. Couple screws and you can remove and clean it if it’s carb up
@bichitoarroyor87266 жыл бұрын
Jonquil lawn & landscape if you take that out and the deflector that holds it, the half moon 1, it makes more noise, and it feels like it's more responsive we u accelerate
@gregsmilgin63686 жыл бұрын
Doesn't turning high clockwise lean it out?
@jonquillawnlandscape84916 жыл бұрын
Greg Smilgin correct
@jodyjo_gd36 жыл бұрын
I will try this tomorrow. I changed everything, fuel filter, air filter etc still bogs down.
@jonquillawnlandscape84916 жыл бұрын
Joey Vance any luck??
@jodyjo_gd36 жыл бұрын
Jonquil lawn & landscape runs great. It actually runs better now than when I first bought it.
@bichitoarroyor87266 жыл бұрын
What happens wen 1 of those run estroge for like 5 min and then shuts off?
@snoopfurlow12755 жыл бұрын
Either the coil or check the muffler screen,spark plug
@ektorcolon73685 жыл бұрын
👍👍👍👍👍
@locindonava36806 жыл бұрын
Can u post web adress of where u purchased that tool... Thanks
@jonquillawnlandscape84916 жыл бұрын
Locindo Nava no clue where I found it. I googled it
@ladodgers95746 жыл бұрын
Do u need put motor oil ?
@kennyplay59823 жыл бұрын
@@ladodgers9574 what are talking about?
@isaaccristan82583 жыл бұрын
I have a 770 and I know it shakes when it idles. But mine shakes bad. Is there anyone who can help me with that
@garrettstevensen24674 жыл бұрын
Damn. A camera tripod is your friend.
@charlesdjones12 жыл бұрын
03:30 that's what she needs, yessir!
@spog73045 жыл бұрын
Walbro “long D” and walbro “large D” eh? So the long d is long and skinny and the large d is shorter and fatter? Think the guys at walbro were laughing their asses off when making those took names?