ABS Pump Failure Symptoms - How To Test And Fix!

With so many ABS fault codes meaning the very same thing, it’s sometimes hard to keep up.
Tim’s going to take you through some ABS pump failure symptoms for the fault description - ABS Pump Motor - how to diagnose and how to resolve these issues
Common fault codes:
• 0070 - Power Supply Pump Motor, Faulty Signal / 0072 - Pump Motor Mechanical Fault
• 01276 - ABS Hydraulic Pump V64 Malfunction
• 5001- Pump Motor Fault
• 52-1 Pump Motor Fault / 51-1 Pump Motor
• 5DF0 - Pump Unit Faulty / 5DF1 - Pump Unit Plug Faulty
• C0020 - Pump Motor
• C1061 - ABS Pump Motor (In Hydraulic Unit) Circuit
• C1095 - Pump Motor Circuit Failure
• C10D3 - Pump Motor Faulty
• C1380 - Pump Motor Fault
www.ecutesting...

[@prestonthulsie1528]

This what all automotive videos should be like to the point and informative very well done

[@bessarion1771]

If you have Mazda 3, there is a valve that gets stuck WITHOUT an error code. The brakes will feel mushy. You need to get on an unpaved road and brake hard activating ABS 5-10 times. This will unblock the valve. No diagnostics or replacement needed. You are welcome.

[@mymonster156]

Same issue with my 2012 Subaru Legacy, and at the same time, my sons Subaru 2016 Forester! Very dangerous when you suddenly can't brake! The brake experts replaced calipers , pressure flush, at lots of expense! Problem may repeat. A serious safety issue!

[@JokersHangout]

Yeah unless you have adaptive cruise control

[@kyleellis4360]

​@@JokersHangout what do you do if it does have adaptive cruise control?

[@AudreysKitchen]

I've heard the issue comes back after some time though. What has been your experience with this? Also does it cause leaking from ABS module? Mine appears to have some leaking...

[@bessarion1771]

@@AudreysKitchen Yes, it has come back. I did the same reset and it's been fine, except that I did not need ABS since this winter. In the end, you have to replace the valve at some point.

[@jeffmosier3145]

Wish all auto vids were clear and precise as yours. I just bought a 04 Pontiac Bonneville in wonderful condition except the abs pump had a leak from underneath the black cylinder. It was where the elec harness is mounted. Took off the module and used a whole can of brake cleaner inside /out then used permatex on the harness gasket and reattached it. Prior owner was using E brake to drive it. Do you figure the pump is burned up cause he left all harnesses connected and no fluid in the system? The brake system is bone dry I'm sure. Don't want to waste time putting module back on , replace fluid and bleed for nothing. Any advise would be greatly appreciated

[@jaimemartinezMogu]

Very very very nice! Great job!!! Thanks for this video...

[@Eurospec73]

I believe I've had a faulty ABS hydraulic pump on my VW Corrado SLC for many years now I took a pair of alligator clips from the battery to the motor and all I heard was a click, the motor never turned on, that's how I know it's faulty. I've got the worst parasitic draw because of it. I'm going with a non ABS swap!

[@HopeWeems-m7h]

I have a 07 buick lucerne, and I don't have no lights on, but my car sides from time to time when I press the brakes. What could that be

[@darrenpenman7076]

I have a seat ibiza. My abs light and handbrake has come on and buzzing from pump even when engine is off. Even took fuses out and still buzzing. Gotta disconnect battery to turn it off

[@Ecutestinglimited]

Hi. The ABS pump running continuously is a common sign that there is an internal fault affecting the ABS unit. If you would like to get your unit tested and potentially re-built, please visit our website and find the unit which matches the part number printed on your ABS. You can then fill in our online test form: myaccount.ecutesting.com/ for details of how to send it in to us. If you have any questions, please contact our technical support team via email on [e-mail] or by calling [phone] (Mon-Fri 9am-5:30pm BST) with details of the fault, the make and model of your vehicle, and the part number of your ABS unit. They will be able to advise you further. Thanks

[@bradh6185]

The constant music noise. WTH? I had to bail.

[@MRMAN-wb1tv]

*I have a 2004 Lexus GS300 with the fault codes of C0246 open/short circuit SRR brake booster, C0256 O/S circuit SRL, C1223 Malfunction ABS control module. All wheel speed sensors read correctly. Is the Malfunction Code do to the first two?*

[@DebtFreeCars]

Will a bad abs module cause my brakes to lock up? Then i have to loosen the brake lines at the master to relieve the pressure.

[@Ecutestinglimited]

Hi. Yes a faulty ABS unit could cause brake binding. Check out the video we did on this here: kzbin.info/www/bejne/iKO2n2ODbNNsm6c If you suspect your ABS is at fault and want to send it into us, please fill in our online test form at www.ecutesting.com.

[@amalfiphone6736]

Dash ABS warning light on. Worried this might be a failed ABS module, or maybe a loom/connections issue? Have just replaced longitudinal, was about to do a Basic Settings recalibrate, but not possible. Seems to drive fine despite the errors. Ideas?! It's doing my head in, and I need to get an MOT! Mk4 Golf, v6 4motion, 2000. VCDS scan output below. ------------------------------------------------------------------------------- Address 03: ABS Brakes Labels: 1C0-907-37x-ESP-A.lbl Part No: 1C0 907 379 F Component: ESP ALLRAD MK60 0103 Coding: 0023046 Shop #: WSC 31414 000 00000 VCID: 2D56919BB7029956C6-5000 5 Faults Found: 01279 - Longitudinal Acceleration Sensor (G251) 008 - Implausible Signal - Intermittent 01542 - Yaw Rate Sensor (G202) 012 - Electrical Fault in Circuit - Intermittent 00778 - Steering Angle Sensor (G85) 003 - Mechanical Failure 01435 - Brake Pressure Sensor 1 (G201) 012 - Electrical Fault in Circuit 00538 - Reference Voltage 012 - Electrical Fault in Circuit

[@Ecutestinglimited]

Hi. Please contact our technical support team via email at [e-mail] with your message and they will be happy to assist you. Cheers

[@amalfiphone6736]

Thanks!

[@TEXASDAWG09]

I have a Ford Fusion 2011 Code is B1676. I replace battery / replace master cylinder. Need help please

[@spyder2001]

Hi, i have a 2009 Scirocco 2.0tsi. ABS & Traction lights came on randomly along with a flashing handbrake light. Took it to a garage that reset the error codes and the issue went away for about 15 miles; now it is back. Brakes feel fine, no issue with the way it drives either. Code is 16352 - Control Module - Defective. Is this something your rebuild service can sort out? Your rebuild cost is really reasonable considering i have been quoted for a new module @ £1,200 plus 5hrs labour...

[@Ecutestinglimited]

Hi. The 16352 code is a very common sign of a faulty ABS module, and we do offer a re-build service for your vehicle. If you fill in our online test form at ecutesting.com with the following details; Vehicle make and model, ABS part number, details of the fault as you have described above and any fault codes, then our technical support team will advise you further. Cheers.

[@djmike281]

Hello I'm in the US I have a 2018 Ford Transit connect two of the wheels the front driver and the rear passenger both calipers are dragging I have already checked both calipers and already checked the brake lines The only thing I can think is maybe the ABS module is keeping pressure supplied to those two calipers please help me😢

[@ANHARISBEAST]

Lol I've got a seat leon tsi for my first car has the same exact problem and fault code going to send these guys my abs pump for a recondition

[@totallyunmemorable]

Damn that music!

[@dexietyy7922]

I have a MK6.5 Ford Fiesta with the abs light on I’ve plugged it in and it says “ low voltage to ABS pump “ what does this even mean haha

[@Ecutestinglimited]

Hi. The low voltage code means the ABS pump is not receiving the correct voltage in order to function. We would recommend checking the wiring to the ABS unit and the connector for any signs of damage. It is also worth checking the relevant fuses as detailed in this video. It could be that the ABS pump itself is faulty, so if everything else checks out ok, then please contact our technical support team via email at [e-mail], and they will assist you further and recommend any re-build solutions we can offer. Thanks.

[@dexietyy7922]

@@Ecutestinglimited hi there thanks for the response it keeps blowing the 30A green fuse for ABS system so I’m guessing the ABS pump is fried or the connection has water inside or corrosion

[@Ecutestinglimited]

@@dexietyy7922 Hi. If the fuse keeps blowing then the problem could either be with the ABS itself or the wiring to the ABS. To differentiate which it is, disconnect the ABS unit and test for continuity between the ground and 12 volts signal on the wiring loom. If it reads open circuit, the ABS is faulty, but if it isn't open circuit then there is a short somewhere in the wiring loom. Hope this helps!

[@vernoncampbell811]

Voltage drop would be from B+ at battery to the power wire at module. You did available voltage tests

[@frikkiesmit327]

Can hear this guy doesn't just talk he knows what he is doing. And is correct with voltage drop. From my experience and as a electronic technician old school one taught me also. A voltage drop can also be to a short circuit that has some resistance. So it can cause problems like on cars your battery life gets shortened. And you basically get 2 types of short circuit one with 0 resistanc which causes fuse to blow usually. And the one with resistance so the fuse doesnt blow yet you get battery drainage issues. And i have seen it in the past. Few months ago i worked on a Toyota hilux which had extra battery in for camping lights and so on. The owner asked me if i could test if there wqs 12volt at the connectors at back of rhe vehicle. I tested the ground 1st and its fine. 12v side dead. So went to engine compartment test that battery 0volt! He is like what?! 0 volt?! That cant be. I also tested a 100 amp fuse which is also fine. So he went in to make some coffee and now my brain is thinking and im like yeah 0volt is extremely flat. So i removed the positive terminal on that battery tested again and i got like 2 volt literally 😂. The moment i touched the positive terminal on battery volts drop immediately so theres a short circuit somewhere in that harnass. The client also said the people that fitted his reverse camera suspect that they might have damaged some wires. So yeah just to be extra safe i insulated the positive terminal. So in mean time the client can take vehicle to the workshop that fits the camping accessories and so.

[@alangrant5278]

I checked the 40 amp fuse for the abs motor and the fuse is good but there’s only 4.5 volts there. Any idea what could a use that?

[@mahtzechuan1732]

hi, my car is 2011 year ford fiesta 1.6s. I have faulty ABS code U3000, I cannot to found the problem pls help. Thank you

[@Ecutestinglimited]

Hi. The U3000 fault code can be a sign that the ABS unit itself is faulty and may need to be re-built. If you would like to do this, please send details of your make and model of vehicle, unit part number, and the details of the fault to our technical support team at [e-mail], and they will advise you further. Cheers.

[@javierardanaz77]

Hello, I have a question about an ABS module that was replaced second-hand on a Mercedes W221 320 cdi. The module has the following ref: A2215458732. It has been verified that the connector has two direct positive supplies, two correct grounds, positive after contact, with values ​​of 12V. The Can Hight and Can Low connections have been tested, the sum of which is 5V (2.65+2.35), the resistance between them is 60 Ohms. Am I missing something before diagnosing that it is the ABS module, the culprit for there being no communication? Regards.

[@kristopherdetar4346]

ABS SUCKS !!! Been driving for nearly 50 years. Cars before ABS rarely has any brake issues. Now these fucking ABS systems have caused more down time making me lose more money than these units worth.

[@mehmetakifkucuk1418]

I have a 2001 ford focus. After renewing the entire brake system, the brakes started to fail. All parts were renewed but it did not improve. Finally, it was decided that the ABS unit was defective. Is the problem really caused by the ABS unit? Or is there another reason?

[@CarlosVarona-g7z]

Is it possible that the ABS module could be damaged after having changed the brake fluid in the traditional way? The traditional way of applying the brake, loosening the bleed valve, etc. When changing brake calipers, the brake pedal sinks. We have changed everything, bled the system and it is still the same.

[@aminmohamad4935]

when going over 60 in a 2012 honda pilot, sometimes vtm4, traction, and abs light come on. After you turn the car off and drive down the road, they disappear. Anyone know the cause. Might be an abs sensor but who knows...

[@gw3705]

I hope you post your solution. I had a wheel sensor turning five warning lights on, sometimes. Then it was all the time. I bought a scanner but I was hoping the wheel sensor would fix it. It did.....all but ABS and traction lights and cruise control. WTF. I'm hoping to fix it still.

[@tyroneturbos6916]

Most common stuff I've seen recently is open circuits in wheel speed sensors traced back to ABS pump

[@Ecutestinglimited]

Thanks for the comment, and you are correct Tyrone! Part 2 of this ABS fault series is going to cover wheel speed sensor faults, so watch this space over the next few weeks! Edit: Here is it! - kzbin.info/www/bejne/imiXc5KXerGhi5I

[@gw3705]

I hope to discover how to repair 2016 VW flashing abs and traction control. (after replacing a bad fl wheel sensor) I also had/have no cruise control when the five warning lights were on. Now it's just ABS and TRACTION flashing in unison, and I gotta get my cruise working before I get a speeding ticket.

[@joshscott8678]

04 tundra double cab abs light ,speed sensors,speedo,wheel bearings raised lspv ,soft petal

[@johnesmer5635]

Alli can hear is stilly music

[@abdulwali4696]

22 civic abs module diagnosed bad. If I replace it will it need to be reprogrammed?

[@JakkiPi]

my 2015 c-max hybrid will not release the brakes when in the hot sun, then sometimes flags the abs light. If I feather the accelerator, it eventually releases. Also, if I switch from reverse to drive, it will release also. The compressor sounds weak and slow. It's like it's gotten weaker over time. Braking during operation is not a problem. In fact, sometimes it's too strong, especially under 10 MPH. The dealership quoted $2,500 to replace the whole ABS module. Looking at the troubleshooting report, they're basing it mostly off the code and test values. No mention of the sensors being tested.

[@Ecutestinglimited]

Hi. Please send the following details to our technical support team via email at [e-mail]. Your vehicles make, model and year of manufacture, the part number of the ABS unit if possible, the results from the troubleshooting report including any fault codes present, and the symptoms of the fault as you have described above. They will advise you further. Thanks.

[@RianKurnia]

Kompenen apa yang rusak jika muncul kode kesalahan U3000 control modul supervision software failure? Apakah ic yang rusak? Mohon di jawab. Terimakasih.

[@picwick57]

I'm in the thick of things right now with my 06 GMC HD2500. I 'm using an old Snap On brick so did a bleed test & know ABS motor works, but pedal blowby felt where it should push back against foot during this test. I have done a road test & speed registers at all frt & r. WHEELS . If I delete abs light & drive off,ABS light stays off during complete drive cycle. Only when I shut truck off turn back on ABS light glows but yet no codes are being registered!! truck brakes fine otherwise. everything on truck is new from last year and nothing is worn & no seized "calipers" including a new master & hydro boost. Will check wiring for bad ground or ?? Coincidence after replacing a bad RF hub bearing yet, speed sensor registers ok! Thanks for sharing your knowledge!! you gave me a couple more tips to check out !! THERE IS A REASON AND I HATE UNWANTED DASH LIGHTS !!🤣

[@marko7843]

I hear you! I have a '97 Riviera with a Teves/ATC ABS/TC system that fails the pump-motor voltage test at 12mph after a hot soak. I've replaced the fuse & relay, cleaned the contacts with electronic cleaner, and even replaced the EBTCM with a wrecking yard unit. The pump always works when I need it, but the 'judge' in the module insists on deactivating the system & lighting the dash lights because it doesn't like the feedback voltages from the motor... Arghhh!

[@PJWALL89]

I'm driving scirocco 1.4 tsi and the car had error code 01130, anyone know if this really ABS pumps faulty or maybe sensors, fuse etc. Thanks in advance!

[@Ecutestinglimited]

Hi. The 01130 fault code is usually caused by either a blown fuse or a faulty ABS unit. We would recommend testing the fuses first before condemning the unit. If you believe your ABS unit is faulty and would like to get it re-built, then please visit our website: www.ecutesting.com/common-faults/volkswagen/vw-01130-abs-operation-implausible-signal/ and select your vehicle make for details of how to send it into us. Make sure the part number matches the one on our website, and if it doesn't, then please email our technical support team on [e-mail], or give us a call on [phone], and they will be happy to assist you further! Thanks.

[@CrisSenior]

abs 30 amp fuse blowing when driving over 15 mph an abs light will come on. All ok when under 15 mph, fuse ok an abs light of

[@Ecutestinglimited]

Hi. It could be that your ABS is causing the fuse to blow. If you would like to send your unit into us for testing to confirm this, then please contact our technical support team via email on [e-mail] with the following information. Your vehicle make and model, the part number of your ABS unit, the fault symptoms as you have described above, and any further relevant details such as fault codes or attempted fixes. They will be happy to assist you further. Thanks.

[@MrNeildavies3]

I have a mk5 r32. The esp button does nothing and no traction. Ive already had the haldex pump replaced. Could the abs pump/module cause this issue?

[@Ecutestinglimited]

Hi. Yes, a faulty ABS pump/module can cause the ESP light to become permanently illuminated. Have you scanned the vehicle for any fault codes at all, as these can help determine the diagnosis. If you are able to do this, please email the results of the scan along with the information you have provided above, to our technical support team - [e-mail]. If you are also able to include the part number printed on your ABS unit, then they will be able to advise you further. Thanks.

[@Gypsy_Danger_TMC]

Went on your site but apparently you guys cant fix my model on my berlingo

[@AnilNigam-k8i]

Hello, I have a 2001 porsche 996 C4 with PSM. I have several symptoms right now: 1) the pedal sometimes becomes very hard or 2) sudden braking without any pressue being applied to the brake pedal. When either of these happen, ABS light comes on on the dashboard. Code 4460. I switched out the brake pedal switch which did nothing. I had the ABS electronic module verified and was told it was fine (no open circuit) and the problem is the hydraulic unit. When brakes come on unexpectedly, the only way to relieve pressure is to disconnect one or more brake lines from the ABS unit and then reconnect. Does this confirm that the problem is the hydraulic unit itself? Thanks for our help.

[@thumbsocial6754]

My abs pump fuse (30A) keeps blowing. Breaks themselves are fine. Could it be : 1) blown motor 2) sticking relays? 3) short, such as wheel sensor? Where should I start?

[@markheatherly2915]

C1440 and c1963 2011 f150 66000 miles brake fluid changed at 50000 lights reset after each restart but sometimes can drive several miles before they come back on sometimes can barely move the truck and they come on wandering if the problem is abs module or transducer in pump housing which I understand is unserviceable and parts cannon shot is 2000 I can’t imagine what the dealer would say but I am interested in verify problem myself before I present it to a shop as this information would help narrow my search in the landmine field of good guys and bad guys also tempted to buy the equipment and repair for free as many as possible to get back at the bad ones my plan is only flawed by making the good ones suffer as well please help if you can I appreciate your time and effort to enlighten us all

[@rajendraamberkar9512]

In some cases fuse faulty but service center guys change whole abs control unit 😰.

[@joelove541]

2014 Subaru Outback. I was driving on a rocky road and right after my brake pedal goes almost to the floor before it slows down. Replaced the master cylinder and still the same issue. No codes or lights are on. Any ideas?

[@satwikmacharla007]

Hello bro my mt15 V1 front brake feels spongy even after several brake bleeds, zip ties, and even after replacing mckit . But abs sensor light working good i feel abs is triggering but can’t figure out this spongy brake. Service centre guy simply told abs rotor/motor problem which costs around 13k . Im confused is this really a abs issue or any brake hose or calliper?

[@juanlazar8945]

gracias por tus veritables consejor¡s y por compartir tus metodos, te sigo desde hace tiempo y me gusta tus profesionales metodos de diagnostico, many thanks

[@cransaftvalve734]

Is it possible that the ABS module could be damaged after having changed the brake fluid in the traditional way? The traditional way of applying the brake, loosening the bleed valve, etc. When changing brake calipers, the brake pedal sinks. We have changed everything, bled the system and it is still the same.

[@kazmegaming4384]

I got tested my car’s abs from the company and they told me my ABS valves are faulty. What’s the solution?

[@Ecutestinglimited]

Hi. If you have a faulty valve then you can either get it re-built by a specialist such as ourselves, or buy a replacement unit. Fill in our online test form at www.ecutesting.com to get it re-built, or find your make and model of vehicle on our product catalogue for up to date pricing. Alternatively, if you cannot find your car on our website, email us at [e-mail] with you car's make and model and details of the fault and our technical support team will assist you. Many thanks.

[@YANDEX30V]

Hi. I've got abs and EBD lights lit on iveco.. ran diagnostics.. only, no braking system.detected.. where do I go from there? Please tia

[@nedunonnyp704]

If I'm able to Run My ABS Pump with My Scan Tool and activate all the valves. Doesn't that mean that My fuses, wiring & electricals are good/intact? 2015 Infiniti Q50. Chasing a C1138 Code.

[@dennissalisbury496]

My 2004 Land Rover Range Rover HSE 4.4l with BMW M64 TU has the DSC disabled and replaced with a coil spring system is this the cause of my ABS red light fault with no codes?

[@paulscot9417]

unfortunately, ECU testing wasn't able to test module, which is a pity as they are a very professional outfit😪

[@kva_powerup]

Hi, I have an issue, I parked my w204 c300 4matic mercedes 2010 for about 3 weeks and when I drove it for like 4meter away the brake pedal went flat momentarily ( happened 3 times ) after which it normalized, since then I haven't driven it again, please I would like your help on what could be the cause

[@Ecutestinglimited]

Hi. A brake pedal going completely to the floor could be a sign of low brake fluid, air in the brake lines, issues with the master cylinder, or a leak in the system. Checking the brake fluid level and condition is essential, and you might need to bleed the brakes to remove any trapped air. Checking the master cylinder or brake callipers for leaks would also be worth doing. Hope this helps!

[@kva_powerup]

@@Ecutestinglimited the fluid is intact and also never worked on so not certain of air trapped in, also the calipers work fine when I step on the brakes but there a slow return from the pedal , and also it sinks in after some seconds of hardness when been stepped on

[@richmaya]

This would all have been great to know before sending my unit in, but your website didn't offer any of this advice. I hope it is a fault with the unit as I'm supposed to be taking the van away in less than a fortnight, and I will have almost no time to find the problem once I have the unit back. Maybe you should link this video on the website, so that people are more likely to have checked all of these things before they remove the unit and send it in?

[@e-ride]

Hello, If the voltage is high? Around 16~18 V? Thank you. And nice video.

[@cj1613]

Does anyone have any reviews of this company rebuilding the unit and offering the lifetime warranty thinking about doing it???

[@e-ride]

Hello, if the voltage is high?. Around 16~18V. Thank you and nice video.

[@nounoufriend1442]

Hi we have 2012 Citreon relay ABS plus traction control faults on dash , no speedo and not registering miles , scanned got configuration fault (configuration not suited to vehicle ) Fault in the alignment of the configuration between ECU's (used Foxwell NT 530 scanner . Been into Citreon dealership (local garage advised to ) couldn't bottom fault , so sent download off to Citreon tech been told fault is ABS pump/module ! doesn't show ABS module fault on scan , reads wheel speeds ok ,What do you think

[@MrFrankGallagher]

UO121 Code astra J . Is this abs control module fault ?

[@Ecutestinglimited]

Hi. A U0121 fault code can certainly be set by a faulty ABS control module. Please contact our technical support team via email on [e-mail] with the following information. Your make and model of vehicle, any relevant diagnostic information such as fault symptoms and codes, and finally the part number printed on your unit. They will be able to assist you further. Thanks.

[@JokersHangout]

Get a 2012 2013 with adaptive cruise an loose all brakes... that's a fun feeling. An can't find one.. channel b valve stuck no communication with module...

[@jhargrove1108]

What is the name of your business if I want to have one repaired or exchanged?

[@Ecutestinglimited]

Hi. We are ECU Testing, please visit our website www.ecutesting.com/ for more information. If you would like to send your unit into us then the best way of doing this is to fill in our online test form: myaccount.ecutesting.com/. Any further questions please don't hesitate to give us a call on [phone] or email us at [e-mail].

[@sadesimmons1474]

I got the code c2402 Hyundai sonata 14

[@nexus2008]

Hi. I have an BMW E87 with error 5E20 . Can help me ?

[@Ecutestinglimited]

Hi. In our experience, the code 5E20 typically indicates that the ABS unit is faulty. Please email our technical support team via [e-mail] with the following information if you would like to send your unit in for a potential test and re-build. The make and model of your vehicle, any symptoms of the fault (including fault codes), and the part number printed on your unit. They will be happy to advise you further.

[@53Talib]

Very nice video. I have a vw passat 2006 B6, 2006 1.9 TDI. I have replaced the electric park brake control unit. it big on diagnosis control unit electric park brake not coded. How to code control unit electric park brake?

[@EBIRCSBUS33]

more over engineered crap

[@fayjason]

I have a a 00 Buick that has 2 codes that came up. 1 is. C1245 the other is 2 C1298. Dos these codes have anything to do with the EBCM. Oddly there are no light up on my dash but when I plugged my computer up to the care these to came up.

[@garbaaliyu9213]

I have Peugeot 301 with abs problem light on when I diagnosed it permanent fualt front weel sensor no signal the four sensors has no signal so I change the abs module it did work and I took the module to another car it work fine and I change the four abs sensor it did work I change the week bearing it did work I checks on

[@vladandjokic1794]

my car is audi a4 b5 1996 quattro. On diagnostics, it doesn't show an ABS pump error, but all my wheels lock when I press the pedal and stay like that until I let the air out. This has been happening since I jacked the car up, started the car and ran the wheels to idle. They told me that I am not allowed to work with the quattro drive because the pump has built up pressure and now it is constantly working, and that the piston in it was leaking and does not return anymore. Is this correct and is there any other problem? 

[@brotherabid]

Its very rare this issue occurs on japanese cars such as honda & toyota, its common on german cars which they earn alot of profit from selling this part again to the consumers

[@sahsaker]

Thanks for you good explain Put I have problem on pump not module 1st one I change because pump pin on the motor head not release I changed the unit for this reason and 2nd one the pump get oil from all the pin inside and the oil makes short after that I listen the unit working if the car switch on or of then I changed too withe new one My question is can I repair any pump of this 2 defect of impossible If yes I thanks if you explain with vedio Thanks

[@Tomtom62]

PLEASE HELP ME, after replacing the lower control arm & the wheel hub, everything's perfect after an alignment, then 2 weeks later the ABS lite came on then a month later the front passenger side wheel started to grind even when i hit the brakes so today I removed the caliper with the mount and rotor and it still grinds consecutively ? I have a HUGE family get together this Saturday at my brothers (about 200 miles each way) but I'm scared shitless driving up there, PLEASE,PLEASE,PLEASE HELP ME...

[@chelseywashington6158]

u get it figured out!?

[@kellismith4329]

Sounds like a bad bearing

[@dragonslayerornstein1242]

My 2020 Nissan has code for the abs motor pump but the abs light nor the traction control light comes on. Weird

[@SwarupKomalVlogs]

I got a 00285 with the 00668 error

[@bpdenverco]

Hi, 2014 Ram 2500 soft pedal no brakes I can push to floor with a little brake. Did replace master cylinder. Same issue, I have no codes for the ABS system.. any thoughts

[@Ecutestinglimited]

Hi the fault sounds like it is a hydraulic issue. If you have checked the brake lines for damage or blockages and the whole braking system for air leaks then the fault could be with your ABS unit. Please send the part number of your ABS unit to [e-mail] and they will advise you of any testing/re-build solution we can provide. Thanks.

[@ismaelpinedacalleja1763]

Nice video I just bought 2018 dodge ram yesterday with22,534 miles on it,on my way home I got the same light issue about ABS break system I called the dealer today I have appointment tomorrow morning let see if they cover the repairs. 😞

[@jagathchristopher4103]

Grateful to provide this beneficial information to us. It's wonderful your Intellectual skills.

[@orvillesandy]

Which VAG-COM VCDS Works for the vw golf mk5 2008

[@olagrafix8906]

Why does my ABS PUMP off the car when unplugged?

[@djmike281]

Hello I'm in the US every 2018 Ford Transit connect the front driver wheel in the back passenger wheel both calipers are dragging I have already rebuilt the brakes to try to solve the issue and replaced one brake line did not solve the issue I think I have a bad ABS module keeping pressure supplied to those to calipers I don't know what to do please help me😢

[@Ecutestinglimited]

Hi. If you have already replaced the callipers and brake lines then it is likely your ABS is faulty. If you would like to send your unit into us for a test to confirm, then please email our technical support team on [e-mail] with all the information you have provided above, as well as the part number of your ABS unit. They will advise you further on any remanufacturing solution we can provide. Thanks.

[@muhammadzahidali6160]

What about 2014 Ford Expedition, Having ABS fault DTC B1342, once you insert key to run/start ? Then switch off remove key run/start this abs alarm will not come ?

[@Ecutestinglimited]

Hi. It is possible your ABS unit is faulty as we have seen this code appear before when that is the case. Please email our technical support team at [e-mail] with the following details; Your make and model of vehicle, the part number of your ABS unit, the symptoms of the fault including fault codes, and any further diagnostic information/fixes you have already tried. They will be happy to assist you further. Thanks.

[@janinejanine6075]

I have a 2007 Tahoe. Apparently my BPM is discontinued. My brakes are soft. Any suggestions?

[@Ecutestinglimited]

Hi. Have you got any fault codes present when scanning the vehicle? If you haven't then we would recommend checking all the basics, e.g. bleed the breaks to remove any air in the system, check the brake fluid level and quality, check for worn brake pads or rotors, and check for any damaged brake lines. If they all look good, or if you did have ABS related fault codes present when scanning the vehicle, the ABS unit may be faulty. Follow this link: www.ecutesting.com/product-catalogue/chevrolet/tahoe/abs-pump-ecumodule-combined/ and select the part number which matches the one printed on your ABS to get it tested and re-built!

[@loubrooks3344]

Hi I have a 2013 sprinter van it’s been into 3 places to try and find the fault. The abs light came on they replaced to sensors the light went out my brakes are so soft the brake only works on quarter of the peddle. They bleed the brakes then put a new kit in the master cylinder it’s still the same they were all lost with it and it’s still the same can you help thanks

[@Zeeos27]

Hello, I need help, I have a brake workshop, they brought us an iveco daily 35s15 2019 ambulance, when you step on the pedal it goes very low, it does not show an abs failure in the ecu, the pump has no problem, neither do the wheels, everything indicates that the fault is in the abs, it has already happened to us with several vehicles, it is as if the brake fluid left somewhere inside the abs module, has it happened to you?

[@Ecutestinglimited]

Hi. It sounds like it is a hydraulic issue as these generally don't log fault codes or illuminate warning lights. We would recommend testing the hydraulics of the brake system. Cheers.

[@topnad]

Hello, thanks for the video ! Could you, please, tell me where can I buy new ABS pump online for my Ford Fiesta 1.4 TDCI 2012

[@Ecutestinglimited]

Hi. We offer a remanufacturing solution for ABS units fitted to your vehicle, so if you would like your unit re-built then please fill in our online test form: myaccount.ecutesting.com/ We do also stock replacement units, but we will need the exact part number of the unit you require to confirm if we have it in stock. Please email our technical support team at [e-mail] with the part number and they will advise you further. Thanks.

[@longshot82383]

All i need is a diagnostic tool 😂

[@CrisSenior]

ford fiesta code c1145 c1155 c1095 checked sensors ok

[@Ecutestinglimited]

Hi. If the wiring to the wheel speed sensors and the sensors themselves have checked out ok, then it is likely the ABS unit itself that is faulty. Please email the part number of your unit to our technical support team at [e-mail] along with the following details. Your make and model of vehicle, any symptoms of the fault including the fault codes you have listed above, and any other relevant diagnostic information such as the tests you have already conducted. They will be happy to advise you further. Thanks.

[@Ranglin1975]

I have a 2019 ford transit all these lights are on abs,tcs, and uphill assist are disabled as i had to unplug the abs pump cuz it wont stop running killing my battery. Any thoughts what this could be? Please help

[@Ecutestinglimited]

Hi. The symptoms you are describing likely indicate a fault with the ABS unit itself, however we would recommend getting the vehicle scanned for any fault codes to confirm. If you are able to do this, please email our technical support team at [e-mail] with the results of the diagnostic scan, the symptoms you have described above, and the part number of the ABS unit itself, and they will be happy to advise you further. Thanks.

[@Victorluca1290]

Could It Block partially 2 wheels and not show any failure or error?

[@moneymakerforfree]

Hi, i have a ford fiesta 2009 model. I got p0500-00 and C0031-07 fault. It says front left sensor but i have already changed it and bearing as well but still got same problem. On diagnotic tool the speed shows 0km/h. Can this be the wiring or abs module?

[@Ecutestinglimited]

Hi. If you have already changed the sensor and the fault still remains then you are right, there could be a problem with the wiring to the sensor or the ABS module itself. We have another video which goes into a bit more detail surrounding wheel speed sensor faults and how to diagnose where the fault lies which you can view here: kzbin.info/www/bejne/imiXc5KXerGhi5I. We would recommend first checking the wiring to the sensor to make sure it is receiving the correct voltage and it has a good ground. Follow the steps in the video and if the wiring checks out ok, then continue to follow the other steps in the video to confirm it is the ABS unit that is faulty. If this is the case then please contact our technical support team via email at [e-mail] or visit our website www.ecutesting.com to get your unit re-built. Thanks.

[@eyobmamo7007]

I have question is that possible

[@NyteOwlDave]

The ODB2 reader reports no codes. The dash panel gives an ABS related message. The motor attached to the ECBM unit runs continuously. Any advice?

[@Ecutestinglimited]

Hi. The motor continuously running sounds like you may have a faulty ABS unit. Please email our technical support team at [e-mail] with the following details; Your vehicle make and model, your units part number, the symptoms of the fault as described above, and any further diagnostic information (e.g. results of scans or any fixes attempted already). They will be happy to assist you further. Thanks.

[@cliffharker2600]

I am getting ABS Sensor errors, front outside, rear nearside. Also power steering Malfunction, several other communication errors When i test voltage at the plug these are 9v, the other two working ones 11.9v I checked the wire continuity to the sensor. I pulled the plug of the ABS module, put 12v in on the correct pins and tested the sensor plug and got 12v. So the ABS module is outputting 9v for these sensors. Why 9v on two diagonal opposed sensors and 12v on the other two? This is a Ford Focus RS Mk2. Would each opposing pair have a different supply maybe? Is the Module in need of removing and refurbishing?

[@Ecutestinglimited]

Hi. It may be that your unit is faulty. Please contact our technical support team via email at [e-mail] with the details you provided above and they will be able to advise you further. Cheers.

[@haybruce9940]

I have a Mazda atenza wagon an my abs module keeps running after I turn the car off completely us there any reason why it would be doin this sorry I dnt know much about cars just wouldn't mind abit of info if some of e can help

[@Ecutestinglimited]

Hi. The fault symptoms you have described are consistent with those of a failing ABS unit. If you would like to get your unit re-built or find out any more information, please contact our technical support team via email at [e-mail] with the following information: Your make and model of vehicle, the ABS unit part number (if possible), the symptoms of your fault (as described above), and any further diagnostic information you can provide, and they will assist you further. Cheers

[@efelinosantana7035]

My problem is That the Abs pump still is on when the car is off and it dry out my battery … Do yall Whats the problem?? And I have a abs lamp on my Dashboard and a red handbrake lamp

[@Ecutestinglimited]

Hi, one of the symptoms that a failed ABS pump and module cause is that of the motor constantly running, even with the vehicle turned off. This is especially true for certain system types, pop an email over to [e-mail] with your part number and we can look into that for you

[@alliswell4374]

How to resolve code in Prius 1.5 hydraulic system RR

[@abdourahmanedia281]

Hello. My kia sportage sometime shows ABS sign and wheel deviation signs. it stops by itself and come back from time to time. no engine check signal. I am not sure if related to driving in water or not. Do you have an idea?

[@Ecutestinglimited]

Hi. If you are able, please use a diagnostic scan tool to obtain the logs when the ABS light appears and email them to our technical support team at [e-mail]. Please also include your make and model of vehicle, any fault codes present and any further relevant information, and they will be happy to assist you further.

[@pamelacowgill9436]

I had a used abs module put on my Volvo S40 T5 and now it doesn't recognize the modulator and I am not certain how to fix that? Can you help a girl out here and possibly tell me how to get it to recognize the new replaced part?

[@Ecutestinglimited]

Hi. If you have replaced the ABS unit with a second hand part, then some Volvo's require the unit to be coded to the vehicle, which will need to be done by a Volvo specialist or dealership.

[@barbergraham6812]

also on a plus side how have you only got 13k subs. you have great content, however we need to find you an audience

[@knighthawk86855]

My code reader says vehicle not equipped with abs, but it is, so I'm guessing no communication with abs controller?

[@Ecutestinglimited]

Hi. We would usually expect to see no communication fault codes present if the ABS has failed in that manner.

[@knighthawk86855]

@@Ecutestinglimited I agree tks.

[@chrisbassaragh2343]

I have an old abs unit from a suzuki that u would like to experiment with. Any knows what voltage goes to the solenoids?

[@theman1233570]

I have a Toyota estima hybrid 2013 with abs fault can this be tested or repaired ????

[@Ecutestinglimited]

Hi. Please contact our technical support team via email at [e-mail] or via phone on [phone] with the following details. Your make and model of vehicle, the unit's part number, and any details of the fault you are experiencing - including fault codes, symptoms and any attempted fixes you have tried. They will advise you of any rebuild we offer. Thanks.

[@ernestdamo677]

Please Chevrolet equinox 2012 with code C56D, electronic control unit hardware malfunction, please what does it mean

[@Ecutestinglimited]

Hi. If you email our technical support team at [e-mail] with your part number and details of the fault then we will be happy to help you out. Cheers

[@abdulhakimnoman7620]

The brake fluid does not reach to the right-back wheel of my sonata car. The abs light is off. Could you please state possible reasons for that? Thanks a lot.

[@Ecutestinglimited]

Hi. If there is no fluid reaching just one wheel then you could have a blocked or damaged brake line or a faulty ABS unit. Please watch our video explaining how to differentiate which could be causing the issue: kzbin.info/www/bejne/iKO2n2ODbNNsm6c (test for no fluid reaching one of the callipers starts at 2:51). If you do believe your ABS unit to be faulty, then please feel free to send it into us and we can comprehensively test it to identify any faults. Thanks.

[@brucetapscott5345]

If I was that good in testing I wouldn't be driving a bad car