Electronic Accelarator Pedal Repair - Astra H

[@joeseda8102]

Did same work on a car. I recommend using an INK ERASER to very lightly clean the surfaces where contact is made by the small contactors. You have to do it very lightly to just remove any small imperfections in the areas where the contactors make contact. I also used 90% alcohol to clean the parts before reassembly. Car ran perfectly after that!

[@kentmccroskey3712]

Contact cleaner, never rub your finger over the resistive track like that, the acid/oils in your fingers will now wear that part even faster than before. spray contact cleaner on both the pins and the strips, and wipe gently with a lint-free cloth. Also, mark where the screws are in the casing before removing the screws, otherwise, you will need to make sure you can retrain the pedal. most cars have a retrain mode activated via odbII, if you don't retrain and you don't screw it back in exactly the same position as before then the resting position will have a slightly higher or lower resistance than before.

[@waleriy116]

За 12 лет работы диагностом-автоэлектриком, я ни разу не встречал неисправность педали акселератора, но всё бывает в первый раз. Гораздо чаще, ошибка по педали имела причину в разъеме UEC, (центр подкапотной электрики). Окислы на контактах разъема, на глаз их не видно. Иногда достаточно просто снять и одеть разъем. Для профилактики побрызгать WD-40. In 12 years of working as an auto electrician diagnostician, I have never met an accelerator pedal malfunction, but everything happens for the first time. Much more often, the pedal error had a cause in the UEC connector, (the center of the under-hood electrics). Oxides on the connector contacts, they are not visible to the eye. Sometimes it is enough just to remove and put on the connector. For prevention, sprinkle WD-40.

[@miticamunteanu2945]

Multumesc frumos pentru informații și va doresc tot binele din lume mitică la toate videoclipuri

[@vpalos]

Great clip! You helped me do the same to my Opel Zafira A accelerator pedal. It was sometimes losing acceleration and was lagging behind (not responsive enough). Everything was fixed after I cleaned it. Thanks!

[@icku]

Glad it helped!

[@omnilife6660]

😢

[@SJSOmar]

This helped a lot as the sensor portion is almost the same as a Saab 9-3s

[@marco45rj]

These black tracks are graphite printed. They are applied in volume controls of various electronic devices. They are delicate. If they show defects in acceleration, change it soon, as the lanes are unrepairable. OK!

[@Hi-Tech-Ray]

I agree and I don't think it was wise of him to add tension to the wiping contacts either, This is also a common problem with the Technics SL1200 series turntable pitch controls!

[@djokovicboris1162]

Tak treba kúpiť nový? Auto ide ale keď sa šlapne na plinovy pedál tak reaguje ale veľmi málo.Alebo vôbec. Ide na voľnobeh. Je zlí pedál?

[@marco45rj]

@@djokovicboris1162 Pri každej práci musíte mať pozorovanie na overenie problému. Takto sa to ťažko hodnotí. Odneste to automobilovému elektrikárovi. OK

[@mp4338]

You forgot to sign before opening the cover because the screw holes are ovales. After close the cover you must to follow the sign.

[@gregdenman2342]

Fantastic camera work, very easy to understand

[@zarularif5466]

I will try it to proton persona if it works.. I will update later.. Tqtqvm sir for your video.. Looks more informative and helpful

[@sehpengpng7631]

Kalau cuci plate elektronik paddle sensor , dapat pakai elektronik cleaner ?

[@sourceallahelohim4521]

Thanks for the video I cleaned my sensor and now it works no codes 😮 thanks again peace and love1

[@paulkomn946]

i did exactly this procedure with my opel corsa c and the light with the spanner didn't open again.

[@balonpromosibalonesia9956]

where can i buy the parts? can you provide the shop link?

[@skydiver4959]

Thank's for this, I'm going to try it on my Malibu.

[@JesusReyes-k7t]

OK HE CLENED IT BUT WHAT WAS THE CAR PRBLEM DOING THIS DO I HAVE TO RESET IT AGAIN OR JUST PUT IT AND WILL IT WORK OR TAKE IT TO DEALER SO THEY CAN RESET IT AGAIN PLEASE REPLY THANKS

[@schiebelcustoms2367]

The light should go out after cleaning but you can disconnect your battery and it will clear the ECU of the codes. If the light comes back, you with have to troubleshoot the circuit again and isolate the issue.

[@mrrobertwolfiii1079]

Appreciate you helping me finish up

[@akashluthra9752]

My swift 2009 diesel accelrstor sensor is not working. Can it be repaired. I got it checked from maruti workshop. They don't have this part I'm their store

[@faisal3374]

If electronic accelerator pedal have play (loose gap) then it will effect the fuel average or not?

[@icku]

No, it won't.

[@ricsajpeti]

Hello, at how many km did the error occur? I'm curious because we manufactured this sensor in 2007 :).

[@icku]

Around 160 000km.

[@primozhrastar]

203 000 km

[@schwuzi]

340000 with my Zafira B

[@nicolasfremont]

Hello what was your ODB error message please ? I do not have any error message but my ODB show me a 16% value when the motor car is just switched ON. I think it is because of the "slow motion motor "...what is your opinion Sir ? Thanks you

[@joehoward6664]

Just what I was looking for, thank you, now I will try it and see if it works for me

[@icku]

Best of luck!

[@avongard1356]

Did it work? I have the same problem.

[@ivanthebig]

So, did it work?

[@lastservant]

Hi AllHandmade, does your acceelarator pedal still work after you did this? Please give me a reply and thanks for sharing, great job.

[@icku]

Yes it's still working. I didn't expect the repair to be such success.

[@johngibson4641]

​@@icku,, ok thanks for awesome video you put on KZbin. I have a gmh Holden Commodore sv8 5.7litre V8 here in Australia. It is going into safety mode yet its not throwning any codes when it goes into safety mode. I have been told by heaps of other people and other mechanics that it may be a pedal could be the issue as this was the first fly by wire that holden ever made and the pedal was a huge problem. I do luv the car as i bought i from my mums inheritance and luv driving it but due to it going into safety mode it is getting annoying to drive and this goes into limp mode anywhere it feels like it (but mainly at bus stops though , haha) and can be very embarrassing too. Do you know where i could seach for the part or could give me an idea on what part number to chase up so i can fix it. Thanks in Advance and Cheers from John , in Australia.

[@icku]

@@johngibson4641 If you can find your car here: 7zap.com/en/catalog/cars/

[@danielntuli3313]

Hi, I own a 2003 vw sharan 1.8t,accelerator is very hesitant and slow, do I have to clean it as shown on the video but with electrical parts cleaner?

[@SifisoMaphalala-vh3zs]

Toyota Quantum 2.7 petrol eccelarate sensor how to replace it

[@user-du5lt5ij7h]

Thank you for this,I love it.And I understand.

[@icku]

Glad it was helpful!

[@EhButU]

Very good - did you repair work - or did you replace part for a new one ?

[@icku]

It worked - problem reseolved.

[@KOSTSAV68]

WD-40 Specialist contact cleaner spray.

[@octavian5548]

1.7 101 cv zth?

[@carldock5223]

Cleaning helps but does not solve. Clean and use a pencil 6B or 8B afterwards. The grease pencil will restore the contacts. ONLY these way you can fix FOREVER the problem. Is it possible that no one understands how these potentiometers really work?

[@icku]

It seems your are one of these guys not understanding how they work. Applying graphite will change the resistance of the potentiometer paths. You can never apply same amount of graphite on the pads/paths - those are layed by machine. So if you do it by hand will end up with one path having more of less graphite then the other/more or less resistance. The ECU is monitoting the voltage drop on two paths if I remember correctly and due to different resistance you will get different voltage - resulting in ECU spewing error codes. A really bad idea ;)

[@carldock5223]

@@icku yeah yeah, do whatever you want, I use graphite

[@halfpack69]

Why did you not reclean the board after you put your thumbs on it? I NEVER chance touching any metal part of the board, unless I clean it after touching it. Better safe than sorry.

[@crusinscamp]

Very good video. This what I was looking for. Has the problem occurred again?

[@icku]

Nope, its working like charm for now.

[@Flowerchild778]

​@@icku A question: Did it need to be reset after this?

[@Savage-lx5yj]

Excellent sir, thanks for sharing

[@nasrahmed6236]

Great explanation thanks alot

[@fingerprint8479]

Hi, nice video, thanks. If I want to buy this sort of circuit board what should I search for? Thanks

[@icku]

No way to source it. At least I didn't manage to find any :(

[@juanpena9386]

That's a new pedal, I see no dust or wear anywhere

[@icku]

Damn, you got me 🤣🤣🤣😒

[@juanpena9386]

@@icku don't get me wrong, what you say might work sometimes. I'm about to disassemble mine so wish me luck

[@kalipso7577]

Короче всё в краце разбираешь чиштишь старательной резинкой контакты и вуаля всё хорошо работает!

[@POM4ALLSHORTS]

Great video very informative thx

[@icku]

Glad you enjoyed it

[@cornelivan6812]

Whatever, i will b esplaining

[@thekrustykrabrestaurant]

It's variable transistor

[@chriswing5187]

Mine is also doing the engine check light and goes into limp mode. So I will try this first

[@icku]

Before that connect the car to Opcom and read the erros codes just to be sure :)

[@tatchik77]

@chriswing5187 did it work?

[@julezbarham9907]

I'm a week away from calling my astra a reef 🏎️💨....... 🐬🐙

[@StratosAsa]

Great video thank you!!

[@icku]

Glad you liked it!

[@Tela-gv8rh]

Si,did it Work

[@icku]

Yep :)

[@suatkaleli5075]

good info

[@yoanfeliz4350]

Thanks boy I can solved my problem 🎉

[@waelawad6566]

V good work

[@FOOTBALL-clix]

Watch the cost of one of these

[@tatchik77]

Mine will cost $399! 🥺

[@marcusmpiana2967]

Honda Pilot 2007

[@cornelivan6812]

Nice effort fell asleep

[@icku]

Well not my fault your not taking your medication ;)

[@askhat4829]

А не легче на русском рассказывать?)

[@АлександрХалабузарь-н8ж]

Было бы не плохо с переводом на русский .

[@Tela-gv8rh]

Bjr